Power Calibration
Verify power measuring instruments accuracy.
See Also: Calibration, Calibrators, Display Calibration, Calibration Standards, Calibration Software, Calibration Services, Calibration References
-
product
Power Line Transducers
Current Transducers measure AC Current and converts it to an industry standard output signal which is directly proportional to the measured input. These Transducers provide an output which is load independent and isolated from the input. The output can be connected to Controllers, Data-Loggers, PLC''''s, Analog / Digital Indicators, Recorders for display, analysis or control. They are ideal for SCADA, Energy Management, Telemetering for Remote, Local as well as Central Monitoring Systems.
-
product
Low Power Comparators
Analog Devices low power comparators provide a capable solution to demanding applications that must operate in the µA range. To cover a range of design needs, our low power comparators are available in commercial, industrial, and automotive temperature ranges, with feature such as noninverting inputs and inverting inputs. This portfolio supports applications such as Li-Ion monitoring, handheld instruments, LED/relay driving, control systems, and optoisolator driving.
-
product
Power Supplies
ZX - SERIES
Coolmax ZX series offer 80 PLUS levels of energy efficiency, massive 12V single rail output gave you the power you needs and super quiet 140mm ball bearing fan create a proper airflow inside the case. 6+2 PCI-E connector is suitable for most demanding SLI or CrossFire systems.
-
product
Pressure Test & Calibration Pumps
Pressure Test Pump is a hand operated pressure pump designed to generate pressure from 95% vacuum to 1,500psi (100bar). A high-quality screw press is designed for fine pressure adjustment, with an adjustment resolution up to 10 Pa (0.1 mbar). A specially designed shut-off valve makes the pressure as stable as possible during calibration. A built-in gas-liquid isolator protects the pump from moisture and dirt to reduce the need for maintenance. Two hand-tight quick connectors installed on the pump allow easy connecting and disconnecting to the test pump without the need for PTFE tape or wrenches. The 918 is an ideal comparison test pump for pressure instruments calibration.
-
product
Three Phase Power Analyzer
Model TFT780
Three Phase Power Analyzer PA700TFT is multi-range power Analyzer with basic 0.05% R+R accuracy. 8 range of voltage, 8 range of current and total 64 range of power and power factor gives more accurate result at low power factor. It has waveform mode to check the waveform of voltage and current. As well it has B/H curve mode where user can check live b/h curve of the transformer under test. The gap less four-quadrant power measurement technique gives better accuracy at distorted waveforms or AC drive (VFD) operated power supply.
-
product
USB & LAN Power Sensor
Setup is fast and easy with the plug-and-play USB connectivity. Simply connect the sensor to your PC and start performing power measurement immediately with the bundled software. With Keysight’s the USB power sensors, you get what you need— simple setup, beyond just a sensor.
-
product
Powered VXI Crates
VXI-C Size 6021
WIENER C-size VXI mainframes of the 6021 deliver highest performance and reliability. Incorporating high density & lowest noise power supply technology the 6021 VXI series is the best choice for any demanding test and measurement VXI application.
-
product
Uninterruptible Power System
S Series
The Clary S Series scientific-grade Uninterruptible Power System (UPS) is built to protect precision instruments, sensitive electronics and medical systems.
-
product
Power Divider/Combiner
Passive devices used mostly in the field of radio technology. They couple a defined amount of the electromagnetic power in a transmission line to a port enabling the signal to be used in another circuit.
-
product
Power Meters & Power Sensors
Keysight’s power meters and power sensors measure the power of RF and microwave signals accurately with sensors of various types (CW, average, and peak and average), covering numerous frequencies and power ranges. We offer a wide selection of power meters and power sensors for nearly all application needs — wireless communications, radar pulse measurements, component test, and more. Applications include testing the output power of communication base-station transmitters, radar system equipment, wireless devices, and much more.
-
product
Optical Power And Energy Meters
Thorlabs' expanding line of optical power and energy meters includes power meter consoles, a large selection of sensor heads, a wireless power meter with a built-in photodiode sensor, and a fiber optic power meter designed for use in the field. The consoles (PM100, PM400, and PM300 Series) when paired with our extensive line of power and energy sensors provide calibrated (NIST traceable) measurements across a broad range of powers, energies, and wavelengths. The console(s) and sensor(s) can be purchased individually or as bundles based on our most popular console and sensor pairings. The sensor calibration data is stored in the sensor head and is automatically read by the console, which allows the user to use multiple sensors with the same console. Compatible sensors are easily identified by the red c-series connector. All of our old A/B-Type sensors are available with the new connector; plus, we have continued to expand our power and energy sensor product lines.
-
product
AC Power Supply
AC Power Supply, Shuangyi AC power products are mainly linear AC power sources: TFC-1000 series
-
product
Handset Power Amplifiers
Broadcom Handset Power Amplifiers support different operating modes (CDMA, UMTS, LTE, and GSM/EDGE) and multiple frequency bands offering premium performance in a very small form factor.
-
-
product
Decade Box, Calibrated, Capacitance, 5, 100pF to 11111µF, 5 %
72-7265 CAL
The 72-7265 CAL from Tenma is a capacitance decade box. It is ideal for service, prototype and experimental use. This useful tool may be set at any non polarized capacitor value from 100pF to 11,111µF in 100pF increments. The decade accuracy is ±5% capacitors used throughout at <1μF, 1KHz test frequency, ≥1μF, 100Hz test frequency. It has weight of 304g/0.69lb and dimension is 14.7cm × 11.7cm × 5.5cm (5.79" × 4.61" × 2.16"). It is typically used in general applications, troubleshooting, maintenance, education and vocational training, production line testing, radio and TV services, working standards, research design & develop, physics laboratory work.
-
product
Resistor Calibration Boxes
RCB-3
Standard Electric Works Co., Ltd
● The RCB-3 is used to verify and proof any High Voltage Insulation Testers. It can be utilized to calibrate all High Voltage Insulation Testers very accurately Analogs or Digitals.● Some institutions and large industries requested their own calibrator too, therefore, SEW started manufacturing the RCB for special customers.
-
-
product
Micro Power, Contact, ITA, Double Male
610143104
(Available preloaded x2 in 510181102 Micro Power, ITA, Insert)
-
product
Three-Phase AC Power Sources
AC6900 Series
Keysight’s AC6900 Series AC power sources provide a complete AC and DC power solution by combining the capabilities of a multimeter, harmonic analyzer, and power analyzer in one instrument. You can easily produce DC power, either alone or as a DC offset to an AC waveform, in a compact form factor.
-
product
Power Assembly Tools
In order to keep up with modern production demands, you need tools that are faster, smarter, more accurate, and more powerful than ever before. Mountz answers that demand from the heart of Silicon Valley with a full line of innovative electric and pneumatic power tools and automation systems. With intuitive Mountz tool controllers, complex multi-pass assemblies become simple and your production speed will skyrocket. Quality control and regulatory compliance can be streamlined with real-time error proofing and time stamped documentation. From the simplest repairs to the most technical manufacturing projects and everything in between, Mountz power tools stand out from the crowd.
-
product
Power device test system
This system is suitable for DC testing of IGBT, IGBT module (1in1～7in1). Built-in hi-current switching relay circuit inside test head, it is capable ofDC testing from device itself to module. Highly accurate repeatability testing is available by high speed rise time which is suppressed its heat in hi-current
-
product
Calibration and Test Equipment Management
Is every value precise? The comparability of measurement results has never been more important than in the present era of globalization. The ability to reduce variables to basic units is the fundamental prerequisite to objectively guarantee, increase, and optimize quality. Our calibration service guarantees full correlation to national standards for test equipment of all physical variables – either at our laboratory or on your premises (for measuring tools).
-
product
DC Power Supplies
DLM 3-4 kW
AMETEK Programmable Power, Inc.
The Sorensen DLM 3kW and 4kW Series programmable DC power supplies are designed to provide highly stable, continuously variable output voltage and current for a broad range of applications in a compact 2U ( 3½” high) chassis.
-
product
Universal Power Line Carrier
UPLC-ll
As with our previous UPLC power-line carrier design, UPLC-II requires no hardware modifications for most required configurations. UPLC-II is frequency programmable across the entire power-line carrier spectrum (30 to 500 kHz) without changing any hardware components. UPLC-II can be software configured either as an ON/OFF or frequency-shift keyed (FSK) power-line carrier unit without changing any hardware components. This flexibility makes each UPLC-II universally suited for any directional comparison blocking, permissive, phase comparison or transfer trip protective relay application.
-
product
1,500-Watt AC/DC Power Supply, Air Plenum
56WS1-01
NAI’s 56WS1-01 is an air plenum-cooled, 1,500 Watt AC/DC Power Supply that converts either 3-phase, AC input or +270 VDC input into a single +28 VDC output at 1,500 Watts continuous or 3,000 Watts peak. This standalone device converts aircraft power so it can be used by system components.
-
product
Power Management IP
We provide a comprehensive set of silicon-proven, compatible IP clusters with the most advanced low-power design techniques.
-
product
Racking & Power
Maximize system reliability, speed up installs and lengthen product life cycles. Universal or dedicated tvONE solutions: we have got it covered with a wide range of elegant and robust racking, power and cooling solutions including the revolutionary ONErack platforms. Our unique solutions are designed from the drawing board to be at the very heart of all your installations as well as adding elegant finishing touches.
-
product
Calibration Test Benches
Nagman Instruments & Electronics Pvt. Ltd
Nagman’s wide range of Calibration Systems – Test Benches, Workstations, Bench-tops & Mobile Units – are designed & executed to serve as Powerful tools for Total Quality Management & ISO Conformance with Accuracies Traceable to International Standards and Total Solution to all Calibration requirements.
-
product
Wind Power Solution
NXA SIEMENS
The NXA SIEMENS is custom-made with firmware and fixtures designed specifically for Siemens 2.3, 2.4, 2.6, 3.6, and 4.0. These precisely designed fixtures make generator-to-gearbox alignment easy inside any nacelle – safeguarding reliability and optimizing the energy efficiency of the wind turbine.
-
product
Electrical Power Transducers
Manufactured for utilities since 1969, TransData Power Transducers are used for measuring AC and DC power variables in Substation, Generation, Load Control and Industrial applications where ±1ma or 4-20mA analog signal are required by the SCADA/Energy Management System. Models are available for measuring Current, AC Voltage, DC Battery Voltage, Watts, VARs, Frequency and more.
