-
Product
78 Pin D-Type Connector Blocks and Breakouts for Pickering Products
-
The connector blocks and breakouts below are suitable to use with Pickering cards and modules that utilize a 78-pin D-type connector.
-
Product
SparkFun Triple Axis Accelerometer Breakout
KX134 (Qwiic)
-
This SparkFun Triple-Axis Accelerometer Breakout is a simple Qwiic breakout for the KX134 digital accelerometer from Kionix. The KX134 is a low-power, 16-bit resolution three-axis accelerometer capable of measuring ±8g/16g/32g/64g (user-selectable) and has up to a 10kHz output data rate making it ideal for high-g measurements as well as high-speed applications such as vibration sensing.
-
Product
Digital Luminosity/Lux/Light Sensor Breakout
TSL2561
-
The TSL2561 luminosity sensor is an advanced digital light sensor, ideal for use in a wide range of light situations. Compared to low cost CdS cells, this sensor is more precise, allowing for exact lux calculations and can be configured for different gain/timing ranges to detect light ranges from up to 0.1 - 40,000+ Lux on the fly.
-
Product
15 Pin Breakout Interface
VSI-Breakout-15
-
The VSI-Breakout-15 is a very useful tool in debugging signals or software in a system. It allows unlimited access to signals within the cabling that might otherwise be difficult to access. The board gives test points at each side of the connector and jumper with a easy to use tabbed shunt to allow for easy disconnection of any particular signal between the connectors. The jumpers also give an opportunity to inject a signal regardless of what signal was originally being driven.
-
Product
SparkFun USB Type A Female Breakout
-
This simple board breaks out a female USB type A connector's VCC, GND, D- and D+ pins to a 0.1" pitch header. If you want to add a USB to your project, but don't want to put up with soldering tiny connectors, this is the board for you.
-
Product
SparkFun Proximity Sensor Breakout
20cm, VCNL4040 (Qwiic)
-
The SparkFun Proximity Sensor Breakout is a simple IR presence and ambient light sensor utilizing the VCNL4040. This type of sensor is often seen in automatic towel and soap dispensers or automatic faucets. With the ability to detect objects qualitatively up to 20cm away, you will be able to detect if something is there and if it is closer or further away since the last reading. Utilizing our handy Qwiic system, no soldering is required to connect it to the rest of your system. However, we still have broken out 0.1"-spaced pins in case you prefer to use a breadboard.
-
Product
SparkFun FTDI Basic Breakout
Beefy 3
-
This is SparkFun Beefy 3 FTDI Basic Breakout for the FTDI FT231X USB to serial IC. The pinout of this board matches the FTDI cable to work with official Arduino and cloned 3.3V Arduino boards. It can also be used for general serial applications. Built upon the same foundation as our 3.3V SparkFun FTDI Basic Breakout, the Beefy 3 is equipped with an AP2112K voltage regulator making this FTDI basic breakout board capable of handling a current load of up to 600 mA! With the addition of a more "Beefy" voltage regulator your will now be able to power a 3.3V project directly from the FTDI. The pinout of this board matches the FTDI cable to work with official Arduino and cloned 3.3V Arduino boards.
-
Product
SparkFun USB UART Serial Breakout
CY7C65213
-
The CY7C65213 USB to UART serial breakout is designed to provide users with a means to access all available I/O pins on the IC, and to provide a 6-pin UART header that is compatible with other SparkFun breakout boards. This breakout has a microUSB connector and other support circuitry to get the IC quickly up and running.
-
Product
SparkFun Breakout
HMC6343
-
The HMC6343 is a fully integrated high end electronic compass module that can compute and give you a heading direction that’s accurate within a couple degrees. It is tilt compensated and is calibrated to handle magnetic distortions. This breakout board allows for easy use of the HMC6343. All that is required is power and I2C connections to a microcontroller so that the module can receive commands and send data back to the user.
-
Product
50-Pin D-Type Breakout Male DIN Mount
40-967-050-M
Breakout Board
50-Pin Male D-Type Breakout, DIN Rail Mount
-
Product
Telecom & Data Test
-
Electro Standards Laboratories
iagnostic tools such as Breakout Boxes/Interface Analyzers designed for use at the data interfaces of modems, multiplexers, terminals, and computers. Electro Standards Laboratories' Series of Breakout Boxes/Interface Analyzers are virtually indestructible and compatible with RS232, HSSI(SCSI-2), EIA/TIA RS530 interfaces.
-
Product
Universal Breakout Test Fixture
CA-323
-
The CA-323 Universal Breakout test fixture was designed to provide, as the name suggests, a universal test solution for aircraft trouble-shooting. The unit gives the technician the ability to monitor (100) different conductors or open an individual conductor for simulation or measurement. Any avionics component can be extended and in many cases with only a voltmeter and oscilloscope the operation in question of the Unit Under Test can be determined.
-
Product
SparkFun Capacitive Touch Breakout
AT42QT1010
-
If you need to add user input without using a button, then a capacitive touch interface might be the answer. The AT42QT1010 SparkFun Capacitive Touch Breakout offers a single, momentary capacitive touch button with easy-to-use digital I/O pins.
-
Product
50-Pin IDC Connector for Ribbon Cable - Female
40-961-550-F
IDC Female Connector
Ideal for user created termination schemes where the termination is to be remotely connected by a ribbon cable. A mating 50-Pin PCB connector 40-963-550-SM and IDC Breakout with DIN Rail mount 40-967-550-M are also available.
-
Product
SparkFun Transceiver Breakout
RS-485
-
This is a breakout board for the SP3485 RS-485 transceiver IC, which will convert a UART serial stream to RS-485. The SP3485 is a half-duplex transceiver, so it can only communicate one way at a time, but it can reach transmission speeds of up to 10Mbps. This board requires a very low amount of power and can operate from a single +3.3VDC supply.
-
Product
MBoS Support Frame For 40-923A-001 Or 60-103D-001 Chassis
95-901-101
-
Frame assembly for mounting a Pickering 40-923A-001 PXI or 60-103D-001 LXI chassis in the Modular Breakout System.
-
Product
PXI BRIC4 FIBO Matrix Dual 80x4 3pin brkout
40-592A-004
Matrix Switch Module
The 40-592A FIBO (Fault Insertion Break-Out) Matrix Module is a large-scale high density switching matrix based on the Pickering BRIC format. The fault insertion BRICs are designed for applications requiring the simulation of a variety of faults in complex, high pin count, applications involving sensors and control units. Typical faults that can be simulated are open-circuits, short circuits to ground or battery, or short-circuits between input/output lines.
-
Product
Breakout Box and Data Logger
1U643-001
-
The 1U634 Breakout Box and Data Logger was developed for the Cessna Excel to serve as the main diagnostics tool for the aircraft?? electronic modules. It allows access to the module pins, and its internal microcomputer digitizes the signals and transmits them to a PC-compatible computer. Advanced software in the computer displays pin voltages either in numerical or graphical form. Data files can be recorded on disk, and played back at a later time for detailed analysis.
-
Product
SparkFun Spectral Sensor Breakout
AS7263 NIR (Qwiic)
-
The SparkFun AS7263 Near Infrared (NIR) Spectral Sensor Breakout brings spectroscopy to the palm of your hand, making it easier than ever to measure and characterize how different materials absorb and reflect different wavelengths of light. The AS7263 Breakout is unique in its ability to communicate by both an I2C interface and serial interface using AT commands. Hookup is easy, thanks to the Qwiic connectors attached to the board --- simply plug one end of the Qwiic cable into the breakout and the other into one of the Qwiic shields, then stack the board on a development board. You’ll be ready to upload a sketch to start taking spectroscopy measurements in no time.
-
Product
SparkFun LED Driver Breakout
LP55231
-
The SparkFun LP55231 LED Driver Breakout is a self-contained solution for developing and deploying the nine-channel I2C LED controller. Remarkably simple, the breakout is equipped primarily with just the LP55231 LED controller IC, plus three RGB LEDs. It also features pads and jumpers for replacing the onboard LEDs with external ones, and configuring the I2C bus, which allows you to daisy-chain up to four LP55231s. This breakout drives the LEDs using Pulse Width Modulation (PWM), so it is well-suited for variable intensity and color-mixing applications!
-
Product
Modular Breakout System 8-Pin Power D-type Plugin Module for 40-193
95-193-001
Modular Breakout System
The 95-193-001 Plugin Breakout Module is designed to be fitted to a PXI 40-193 Fault Insertion Switch as part of the Pickering MBoS. The Modular Breakout System is designed to Simplify HILS (Hardware In the Loop Simulation) Applications.
-
Product
PCI Express 5.0 Transmitter Electrical Performance Validation and Compliance Software
D9050PCIC
-
Use the PCIe 5.0 Tx compliance software to test, debug and characterize your PCIe Gen5 designs quickly and easily. It automatically configures the oscilloscope for each test and generates an informative HTML report upon test completion. The application compares the results with the specification test limit and includes margin analysis which indicates how closely the device passes or fails each test. With the option InfiniiSim Waveform Transformation Toolset, the software supports integrated de-embedding of the breakout channel of the test fixture.
-
Product
Modular Breakout System for Hardware-In-Loop Simulation
-
Designed in partnership with OPAL-RT Technologies, this Modular Breakout System combines a BoB feature set with the added flexibility of an FIU. By mating the FIU chassis directly to the BoB using our plug-in modules, cabling is minimized, creating a more compact reliable design and improving signal integrity.
-
Product
Sensirion SHT31-DIS-B Humidity and Temperature Sensor Breakout Board
SEN-37002-F
-
Breakout board for the Sensirion SHT31-DIS-F with a built-in permeable membrane filter. This sensor is an extremely accurate digital (I2C interface) temperature and humidity sensing device, with +/-0.2C temperature and +/-2% humidity accuracy typical. These specs far exceed the accuracy of ICs that came before it, including the HTU2x and SHT1x series, and improves upon the success of the SHT2x that came before it. In addition, the SHT31-DIS-B has a wide input voltage range of 2.4V-5.5V and includes temperature isolation and airflow cutouts as recommended for the optimal operation. Finally, in the case of environmental changes that could cause light condensation, the SHT31-DIS-B has a built-in heater to burn off any condensate.
-
Product
PXI BRIC4 FIBO Matrix Dual 93x4 2pin brkout
40-592A-013
Matrix Switch Module
The 40-592A FIBO (Fault Insertion Break-Out) Matrix Module is a large-scale high density switching matrix based on the Pickering BRIC format. The fault insertion BRICs are designed for applications requiring the simulation of a variety of faults in complex, high pin count, applications involving sensors and control units. Typical faults that can be simulated are open-circuits, short circuits to ground or battery, or short-circuits between input/output lines.
-
Product
Modular Breakout System 78-Pin D-type Plugin Module for 40-201
95-201-001
Modular Breakout System
The 95-201-001 Plugin Breakout Module is designed to be fitted to a PXI 40-201 Fault Insertion Switch as part of the Pickering MBoS. The Modular Breakout System is designed to Simplify HILS (Hardware In the Loop Simulation) Applications.
-
Product
LSM6DSL Click
64207
-
Parallax speeds the process of Propeller 2 development through our partnership with MikroE, who has created a family of 850+ Clicks for most I/O functions you may envision. For each of the Click boards stocked by Parallax, you will find a documented Spin 2 code example on our Propeller GitHub Object Exchange. Connect your Click boards to the Propeller 2 Evaluation Board or P2-EC Edge Breakout Breadboard using the #64008 P2 to MikroBus Click Adapter.
-
Product
Prototyping Adapters/Interposers
-
Prototyping adapters breakout from any package type to 2.54mm pitch pins or a larger pitch SMT footprint to solder to your development board. Our extensive design library means that many are available for fast delivery or next day from RS Components.
-
Product
SparkFun RGB LED Breakout
WS2812B
-
This is a breakout board for the WS2812B RGB LED. The WS2812B (or "NeoPixel") is actually an RGB LED with a WS2811 built right into the LED! All the necessary pins are broken out to 0.1" spaced headers for easy bread-boarding. Several of these breakouts can even be chained together to form a display or an addressable string.
-
Product
IntellaView
EdgeSwitch
-
The IntellaView EdgeSwitch is a high-density 1RU system with 32 ports of 40G / 100G Ethernet capability, while the breakout mode can support up to 128 ports of 10G / 25G. The EdgeSwitch enables efficient traffic aggregation, filtering, load balancing, tunnel management, and port tagging standalone or as part of a larger visibility solution.
