Geometry
-
Product
Probe Pins
Cobra-Series
-
Cobra-series probe pins offer long lifetime and low particle contamination for high-density probing applications. We can produce them using different materials and fine pitch geometries.
-
Product
Turbine Flowmeters
-
Titan’s small turbine flowmeter range use a radial flow principle based on the Pelton wheel technique. This well proven method is the ideal way of measuring low rates of flow of low viscosity liquids. For these mini flowmeters, a jet of fluid is directed at a turbine that is mounted on robust low friction sapphire bearings. The geometry of the turbine and the fluid chamber ensures that the rotational speed of the rotor is proportional to the flow rate through the device. The use of this radial arrangement allows more energy to be imparted into the turbine, so the bearing drag is far less important. Furthermore, because more energy is available the bearings themselves can be a lot stronger so increasing the life of the flowmeter. For larger flows, some of the liquid can bypass the turbine chamber, which then behaves as a “shunt” to the metered fluid. Accuracy is still maintained and the output remains linear.
-
Product
High Impedance Active Probes
7
-
Designed as a companion probe to Models 12C and 18C for driving integrated circuit lines so the Model 12C and 18C can be used to measure the response of adjacent nodes. The Model 7 consists of a flexible 6 foot, 50 ohm coaxial cable accurately terminated to 50 ohms in order to avoid undesirable reflections. A special miniature connector receives replacement coaxial probe tips that provide a shielded environment to within 3 mm of the fine tungsten probe point, thus minimizing capacitive coupling to other parts of the circuit. The replaceable coaxial probe tips are offered in various point sizes and can also be bent to any shape in order to accommodate a variety of probing geometries.
-
Product
RANGER-ULTRA
-
The RANGER-ULTRA is an airborne laser scanner with an impressive combination of weight, range, accuracy and pulse rate. It is equipped with a unique forward and rear looking FOV designed to minimize laser shadowing and provide geometry on complex vertical structures on a single pass. With its wide field of view of 100 degrees and an extremely fast pulse repetition rate of up to 1.8 MHz, the RANGER-ULTRA is perfectly suited for high point density corridor mapping applications such as power line, railway track and pipeline inspection.
-
Product
Portable Connector End Face Geometry Interferometer
-
Thorlabs’ Vytran® Connect-Chek® Interferometer automatically and precisely measures radius of curvature, apex offset of polish, and fiber undercut or protrusion on any PC or APC, single-fiber connector. The CC6000 interferometer uses a non-contact tilted-phase-analysis technique for fast, reliable measurements of connector end faces. This compact interferometer has a carrying handle and must be attached to a desktop or laptop computer (not included) with a standard USB 2.0 port for operation. The included CC6000 software, which is used to control the interferometer, can be installed on a computer with the minimum requirements in the table below. Designed for use in both the factory and the field, this interferometer provides crucial quality information needed to assure long-term performance of fiber optic connectors. One CC250P Mount for Ø2.50 mm PC Connectors and one RT250P Reference Tool for calibrating the CC250P mount are included with the CC6000 interferometer; mounts and reference tools that enable measurement of other PC or APC, single-fiber connectors are available separately below. When used with an appropriate mount for APC connectors, the CC6000 interferometer is also capable of measuring the APC angle and key error.
-
Product
Low Temperature Operating Life (LTOL) Test
LTOL
-
LTOL is being more used more and more frequently by manufacturers of low geometry devices as part of the qualification process, and in order to gain more failure data, a greater understanding of different failure modes of the device at low temperature, and to enable more complete reliability estimations. As device geometries decrease and frequencies become higher, Hot Carrier Injection (HCI) increases and the resulting degradation causes the deterioration of device characteristics and ultimately leads to failure.
-
Product
Coordinate Measuring Machines
-
Coordinate Measuring Machines (CMMs) measure the geometry of physical objects by sensing points on the surface of the object with a touch probe. They are commonly used in manufacturing processes to inspect a physical part or assembly against the design specification.
-
Product
Optical CMM Systems
-
Our OmniLux metrology system is highly versatile and provides unparalleled levels of 3D CMM capture for component measurement in seconds. This high precision non contact, metrology system is extremely versatile because it measures components of any geometry and of any material. Geometries possible include: spheres, asphere, cylinder, internal bore, cone/taper, step height or freeform in any material such as polished or rough metals or ceramics and polymers. The Omnilux is fast and accurate because, unlike direct contact sensors, the use of optical sensors means that the whole surface can be analysed while the object is suspended in space, ensuring that no damage comes to delicate surfaces. Our easy-to-use software interface, developed from years of experience enables the operator to effortlessly control the system. Rich data analysis, automation and export of results for the immediate generation of reports as well as a compact footprint means OmniLux is the leading solution for production or R&D environments where reducing cycle times is critical to sustainable success.
-
Product
Hardness Testing Devices
-
Institut Dr. Foerster GmbH & Co. KG
NewSonic’s hardness testing devices test hardness in a nondestructive way using the UCI method (ultrasonic contact impedance). The testing procedure enables quick and mobile measurements (1-second type) to supplement traditional hardness testing. The devices feature compact measurement probes which can also be used in difficult testing positions and component geometries. The areas of application include incoming goods inspection, mix-up checks, production controls, quality assurance, weld seam inspection, cut edge checks, maintenance of built-in components, as well as the replacement of dynamic hardness testing devices in the case of thin materials (below 50mm, e.g. boilers, pipes)
-
Product
AM Control System
Clamir
-
*Continuous monitoring of melt pool dynamics and geometry.*Ensures quality and repeatability.*Compatible with most laser heads.*Compatible with a wide range of materials.*Easy mechanical integration.*Quick configuration.*Helps to reduce CO2 emissions.
-
Product
Probe Card Analyzers
PB6800
-
The ITC line of Probilt, probe card analyzers provide fast, accurate and repeatable test data for all types of probe card technologies. Simple user definable vision parameters allow even the newest and most complex probe tip geometries to be captured and accurately measured. Probilt’s PB6800 large measurement chuck allows probe arrays as big as 300 mm in diameter to be touched down without overhanging the chuck surface.
-
Product
Polaris Tools And Accessories
-
The Polaris® optical measurement solution is designed with accuracy, reliability, and versatility in mind. Versatility is delivered in part by NDI software packages and developer tools that are available to enhance OEM application development and system customization. The Polaris solution consists of an optical tracker and navigation markers, the latter of which must be attached to a rigid body; i.e. a tool that is rigid in form to prevent unwanted marker movement. The Polaris solution requires three or more markers to be attached to the rigid body tool, the geometry (configuration) of which is unique to each tool.
-
Product
Correlation Analysis
-
EDM Modal Correlation Analysis allows the user to correlate two modal models; EMA and/or FEA models. Comparing the experimental data with that acquired through finite element analysis helps in validating the test results. Users can import the geometry model and mode shape data from FEA or EMA software.
-
Product
Circular Helmholtz Coils
-
Helmholtz-Coils are especially designed to generate precisely defined magnetic fields from DC to the upper end of the audio frequency range and beyond. The generated fields are in a strongly linear relation to the coil current. The field- strength can be calculated exactly by analytical (or numerical) methods, based on the coils' geometry, the number of turns and the coil current.
-
Product
Interferometer
VFI-200
-
The FGC range is the complete solution for measuring the dimensions of standard and specialty fiber in both production and R&D environments. FGC-GS – fiber glass geometry for fibers up to 1000 µm diameter.
-
Product
High Precision Angular Position, Calibration and Geometry Inspection
GeoOrdinate
-
Rotary Precision Instruments UK Ltd
Ultra precise rotary tables intended for fine inspection, metrology and test applications.The GeoOrdinate has been designed specifically for the inspection of large and heavy components and is fully compatible with any shop floor environment whilst maintaining world class accuracies more commonly seen in the standards laboratory.
-
Product
3D/2.5D Time-Domain Electromagnetic Field Solver Software
EM-CORE ®
-
3D/2.5D Time-Domain Electromagnetic Field Solver Software for Planar-Circuit and Antenna Simulation. 3D & 2D Radiation Patterns Modeling, Spiral Inductors Modeling, 3D EM Modeling of Filters, Intuitive Geometry Build, and more!
-
Product
Photoelectric Sensors
-
Angle sensors from Balluff are a logical development of Balluff's fork sensors for more demanding applications. Their custom housing design and beam geometry enable approach and recognition of objects from almost every direction. Installation is very simple, even with space constraints: the transmitter and receiver are firmly aligned with each other.
-
Product
HyMPulse Pulsed Field Magnetometer
-
Metis Instruments & Equipment NV
Geometry independent M-measurement (patent pending): One probe fits all, no pole shoes per magnet geometry. Measure the actual magnet instead of a prepared standard size sample. Measurement of industrial shapes like segments, cylinders, bricks,... with one probe
-
Product
Digital Automated Fiber & Ferrule Interferometer For Single Fiber Connectors
DAFFI SF
-
The latest interferometer from Data-Pixel is a cost effective solution for high volumes production, without compromising on accuracy or performance. Based on our extensive interferometer manufacturing experience we designed the DAFFI SF to be robust, fast and accurate in order to meet all manufacturing or laboratory environments. With the Blink software platform, DAFFI is able to measure the end face geometry on single fiber connectors in a very short time. The Daffi interferometer accessories (flange and adapters) are fully compatible with the Daisi range, allowing the user to limit the costs of the 3D geometry measurement units.
-
Product
Hardware and Software Complex for Measuring Geometric Parameters
Vishera
-
Non-contact measurement of the geometry of objects using telecentric lenses Opto Engineering, illuminators of various modifications, 3D scanner Sick Ranger. The telecentric pair, in conjunction with modern digital cameras from Basler, ensures high accuracy in measuring the geometric parameters of objects, the principle of laser triangulation ensures high accuracy and scanning speed.
-
Product
Rock Mechanics
ROCK3D
-
ROCK3D is a program for stability analysis of removable blocks on planar rock slopes. It identifies and analyses all the blocks that have formed under each kinematic mode. Once the geometry of the rock blocks has been identified, the bolt forces necessary to reach a required safety factor are calculated.
-
Product
Benchtop Directional (45°/0° And 0°/45°) Geometry Spectrophotometers
-
Hunter Associates Laboratory, Inc.
Directional (45°/0° and 0°/45°) geometry benchtop spectrophotometers replicate the human visual response to color and include applications where gloss and texture affect the color measurement.
-
Product
Entry-level Price Interferometer for Geometry Measurement of Single Fibers
3D SCOPE-V2
-
Specifically designed for use in a production environment, 3D Scope-V2 is a robust, compact and easy to use interferometer that brings speed and precision to operators. 3D Scope-V2 supports our Blink software platform. Non-compressed, real time and high quality images are transfered from the hardware to the software via a USB 2.0 link in addition to the automation and control commands.
-
Product
Standard Pattern Generator Board
BL-PG315-01
-
The MicroImage PG315 pattern generator is designed for simple size and geometry reference applications. The PG315 will overlay one of five standard patterns including a centered cross line, a centered cross hair, a centered target style symbol, a dot grid (cross dot) array, a hatch grid (crosshatch) array.
-
Product
Spectrometer
AirSPEC
-
Baltic Scientific Instruments, Ltd
Scintillation gamma-ray spectrometer AirSPEC is intended for measuring scintillation spectra and alsofor determination of activities and specific activities of radionuclides in samples and in conditions of natural occurrence in geometries 2 and 4.Spectrometercan be usedfor various tasksradiation monitoring, including the definition ofspecific effective activity of naturally occurring radionuclides (NORM) in building materials (granite,crushed stone, gravel, etc.), raw materials, products, waste industrial productionand rockswithoutsampling; measurements surface activity of the radionuclide 137Cs (and other); mass fraction of NORM in rocks andoresin the conditions oftheirnatural occurrence on a surface, inboreholes and in warehouses andtransportcontainers, and also in study ofsurface contaminationof soil,as well asprospecting and exploration ofmineral deposits resources.The spectrometercan be used forworkin the laboratoryand in the field conditions.
-
Product
PAL Standard Pattern Generator
PG315P
-
The MicroImage PG315 pattern generator is designed for simple size and geometry reference applications. The PG315 will overlay one of five standard patterns including a centered cross line, a centered cross hair, a centered target style symbol, a dot grid (cross dot) array, a hatch grid (crosshatch) array.
-
Product
SANA 2 Interferometer
CA3004
-
SANA 2 fiber endface interferometer is a type of cost-efficient non-contact test instrument with excellent performance. It is able to measure the fiber endface geometry parameters such as radius of curvature, apex offset, fbre height and polishing angle of APC connector.
-
Product
3D Roughness Measurement System
IF-Profiler
-
The If-Profiler is a handheld 3D roughness measurement system for high resolution measurement of surface finish. You measure roughness of flat and curved components with only one system. Measurements are performed both profile based (ISO 4287) and areal based (ISO 25178). The measurement system achieves flexible measurements and applications at high measurement speed. Various positions and measurement fields are traceably and intuitively measured. The IF-Profiler is also used to measure geometries with steep flanks and various coatings.
-
Product
3D-IC Solution
-
Consumer demand for increased bandwidth and low power in smaller form factor has forced design teams to pursue design and manufacturing alternatives to single system-on-chip (SoC) approaches. Moving to advanced geometries like 20nm/14nm is a natural progression; however, it has its own cost, yield, manufacturing, and IP reuse challenges.
