Geometry
-
Product
Passive Probe, 500 MHz, 2.5mm Tip
PP007-WR-1
-
The PP007 embodies leading technology in passive probe design. The small probe is optimized for maximum waveform fidelity, including high frequency signal components, in a rugged probe suitable for every day.The sharp probe tip* is spring loaded, allowing it to retract into the narrow probe head. The tip does not slip off the object being probed—important when probing small geometry surface-mounted components. Probing dense circuits is easier with the small 2.5 mm ground sleeve, which provides much better visibility than 5 mm and 3.5 mm probes.
-
Product
Probe Positioners (Probe Manipulators)
-
PacketMicro offers a broad ranges of probe positioners to allow designers to guide standard oscilloscope/TDR/RF/microwave probes onto the small geometries of fine-pitch interconnects, SMD packages, MCMs, hybrids and ICs.
-
Product
High Temperature Operating Life
7000 Series
-
With ever decreasing geometries, the way we perform HTOL requires careful consideration. In lower geometry device leakage currents are not only higher but vary greatly. Temperature control at DUT level – required to achieve correct junction temperature at every DUT. For higher geometries, HTOL can be performed in a more traditional way but with devices consuming more power, the ambient temperatures required varies greatly. Multiple temperature zones are required – multi zones system or multiple smaller HTOL systems.
-
Product
Contactless Wafer Geometry Gauge
MX 20x series
-
The E+H geometry gauges are based on two heavy plates mounted parallel to each other. Embedded in the plate are a set of capacitive distance sensors. The wafer will be moved manual or automatically between the plates and measured without any movement.
-
Product
Premium Spectral Light Meter
GL SPECTIS 1.0 TOUCH
-
The Spectis 1.0 Touch handheld light meter offers unmatched performance and flexibility. With an interchangeable detector, the system can be used for wide range of applications and measurement geometries. Use in the field, the lab or both!
-
Product
ReMesh
-
ReMesh is the CAD program, which provides powerful tools for geometry creating, checking and editing. Program has tools to remesh discretely or semi-analytically specified geometry in 3D and has convenient interface for editing geometry manually. Problems with remeshing of such geometries arise in EMC simulations.
-
Product
High Power LED Test System
Lumere-GM
-
Evolusys Technologies Sdn. Bhd.
Lumere GM is a LED test and measurement system for various parameters of LED light. It is a high-accuracy system with a temperature-controlled CCD, its geometry conforms with CIE-Publication 127, and the test program is easy to configure and adjust. The Lumere GM is used in laboratory applications and in the production of high-power LEDs.
-
Product
ICP-MS spectrometers (ICP MASS)
-
SPECTRO Analytical Instruments GmbH
SPECTRO MS is a double-focusing sector field ICP MS (ICP mass spectrometer) based on a Mattauch-Herzog geometry with a newly developed ion optic and pioneering detector technology. It is the only ICP MS instrument available on the market today that is capable of simultaneously measuring the complete mass range used for inorganic mass spectrometry from 6Li to 238U with a permanent ion beam going to the detector.
-
Product
Rotman Lens Designer
-
Rotman Lens Designer (RLD) is a software tool for the design, synthesis, and analysis of Rotman Lenses and their variants. It is based on Geometrical Optics combined with the classical Rotman Lens design equations. It is intended for rapid development and analysis of Rotman Lenses given several physical and electrical input parameters. RLD generates the proper lens contours, transmission line geometry, absorptive port (dummy port) geometry, provides an approximate analysis of performance, and generates geometry files for import into Remcom's XFdtd® for further analysis and fabrication.
-
Product
AM Control System
Clamir
-
*Continuous monitoring of melt pool dynamics and geometry.*Ensures quality and repeatability.*Compatible with most laser heads.*Compatible with a wide range of materials.*Easy mechanical integration.*Quick configuration.*Helps to reduce CO2 emissions.
-
Product
X-ray Diffraction and Elemental Analysis
D8 ADVANCE
-
The intelligent beam path components of the D8 ADVANCE with DAVINCI design provide true plug'n play functionality requiring minimum or even no user intervention. Featuring automatic and tool-free switching of the diffraction geometry without the need for complex adjustments, the D8 ADVANCE with DAVINCI design broadens the analytical capabilities for a wide community of X-ray diffraction users.
-
Product
Laser
-
Discover our laser alignment and laser geometry solutions , advanced tools for controlling machine and quality defects. Reliability , precision , and efficiency are at the heart of our solutions to ensure high-quality preventative maintenance.
-
Product
Companion Tool to VS for Test Time & Pin reduction
UltraScan
-
UltraScan is SynTest's solution to combat increase in test time. In 130 nm or smaller ? nanometer geometries, many defects become delay defects and it becomes necessary to use delay tests to detect the transition faults and path delay faults. Often bridging tests are also required.
-
Product
HyMPulse Pulsed Field Magnetometer
-
Metis Instruments & Equipment NV
Geometry independent M-measurement (patent pending): One probe fits all, no pole shoes per magnet geometry. Measure the actual magnet instead of a prepared standard size sample. Measurement of industrial shapes like segments, cylinders, bricks,... with one probe
-
Product
Entry-level Price Interferometer for Geometry Measurement of Single Fibers
3D SCOPE-V2
-
Specifically designed for use in a production environment, 3D Scope-V2 is a robust, compact and easy to use interferometer that brings speed and precision to operators. 3D Scope-V2 supports our Blink software platform. Non-compressed, real time and high quality images are transfered from the hardware to the software via a USB 2.0 link in addition to the automation and control commands.
-
Product
Refractive Index Profiler
S14
-
The S14 Refractive Index Profiler complements optical fiber preform analysis measurements by providing highly accurate and precise characterization of the refractive index profile of drawn single-mode, multimode, and specialty fibers using the RNF (Refracted Near Field) technique. The S14 index profile data produces fiber geometry information directly. Manufacturers can also use S14 data for the prediction of fiber transmission parameters such as mode field diameter, cut-off wavelength, and chromatic dispersion.
-
Product
Geometrical Measurement Software
-
PRÜFTECHNIK Condition Monitoring GmbH
Activate your machinery more quickly, and help it run longer. PRÜFTECHNIK geometric laser alignment tools and software enable you to easily check and adjust your machine geometries for: straightness, flatness, level, inclination, plumbness, parallelism, and right angle check. Our tools are powerful, precise, and easy to use on a vast range of machinery—they can measure for the most demanding alignment jobs, including a bore of almost any diameter, and/or any surface type or inclination. Find the right geometric measurement tool for your machines.
-
Product
Vibration Analysis
-
The vibration analysis software WaveImage includes a full set of methods providing an accurate and detailed overview of your vibration measurement data. This gives you a clear understanding of the cause-and-effect relationships between specific excitations and their vibrational response. Create a simple geometry model of your structure and link your multi-channel measurement data to the points in the geometry where the data was recorded. Then visualize the dynamic deformation of the structure under specific operating conditions with a detailed animation.
-
Product
Benchtop Non-Contact Directional Geometry Spectrophotometers
-
Hunter Associates Laboratory, Inc.
Unique measurement methods that don’t require instrument contact with your samples. These benchtop spectrophotometers are perfect for samples that are not smooth, uniform or are messy. These solutions reduce sample preparation time and cleanup time while ensuring absolute measurement accuracy and consistency.
-
Product
Hybrid Photon Counting Detectors
MYTHEN2 Series
-
MYTHEN2 detectors guarantee noise-free performance, maximum resolution, and outstanding signal-to-noise ratios for an extended energy range from 4 to 40 keV. These systems include two module sizes: 1K with 1280 strips, and 1D with 640 strips. Their compact size, symmetrical sensor position, and DCS4 control unit make the MYTHEN2 series suitable for any diffractometer geometry — from portable instruments to large systems.
-
Product
Wafer Sorter and Inspection
SolarWIS Platform
-
Eliminating the opportunity for problematic wafers to enter cell manufacturing lines greatly improves output and yield. ASM AE’s wafer sorter features 3D area inspection capability to inspect wafer thickness, total thickness variation (TTV), saw marks, as well as wafer bow and warpage. SolarWIS also includes modules that can inspect for stain, geometry, micro-cracks, edge chips, resistivity, P or N conductivity and lifetime.
-
Product
Standard Pattern Generator Board
BL-PG315-01
-
The MicroImage PG315 pattern generator is designed for simple size and geometry reference applications. The PG315 will overlay one of five standard patterns including a centered cross line, a centered cross hair, a centered target style symbol, a dot grid (cross dot) array, a hatch grid (crosshatch) array.
-
Product
Correlation Analysis
-
EDM Modal Correlation Analysis allows the user to correlate two modal models; EMA and/or FEA models. Comparing the experimental data with that acquired through finite element analysis helps in validating the test results. Users can import the geometry model and mode shape data from FEA or EMA software.
-
Product
Day Camera Testing
-
CI Systems' CCD test stations are used to carry out all the necessary tests to verify and compare the quality of a CCD based camera. These stations are based on CI Systems' reflective collimators, Visible Radiation Sources, special targets and integrated software, to project standard patterns with known geometry and intensity to the Unit Under Test. As a result, these stations are turnkey solutions for the CCD camera testing needs.
-
Product
Non-Destructive Testing
-
The essential feature of active thermography is the targeted supply of energy to the test object. A temporal and spatial characteristic heat flow results depending on the geometry and thermal properties of the test subjects. Its progression on the surface of the test object is captured by a thermographic camera.
-
Product
UltraScan PRO Spectrophotometer.
Spectrometer
Hunter Associates Laboratory, Inc.
The D65 illumination source is calibrated in the ultraviolet region for the accurate measurement of whitening agents. UltraScan PRO has an extended wavelength range into the near infrared and near ultraviolet that permits the measurement of camouflage materials and UV blockers. The system uses diffuse/8° geometry with automated specular component inclusion/exclusion. It also features three sizes of sample measurement areas with automated lens change. The UltraScan PRO includes EasyMatch QC software and an electronic record keeping version that is 21 CFR 11 compliant is available.
-
Product
Disposable Spiral Mixers
-
Using simple, time-proven geometry, Nordson EFD’s patented disposable Spiral Mixers™ deliver complete and thorough mixing for a wide variety of two-part materials.
-
Product
Non-Destructive Testing (NDT)
-
Marposs complements its geometric measurement solutions with solutions for non-destructive testing using eddy current technology.The testing options can be divided in three large groups:Material integrity test, to check for the presence of defects (cracks, porosity, blow holes, inclusions) on the surface and in the layer just below the surface.Material properties test, to check if the thermal cycles (hardening, hardening and tempering, annealing, stress relieving, etc.) have been performed correctly. Material identification checks are done to sort parts with the same geometry but made with different materials.Thread inspection to check if the treading has been carried out and its quality.In addition to the non-destructive checks performed with the eddy currents, we have developed a durometer for the conventional measurement of surface hardness, according to the Rockwell scale (HRC or HRA); which uses a diamond penetrator to measure the hardness of the sample being tested.
-
Product
Straightness Measurement Kit
55283A
-
The Keysight 55283A Straightness Measurement Kit, used with the Keysight 5530 Laser Calibration System, makes straightness, squareness and parallelism measurements to identify geometry errors that seriously degrade machine tool performance. These measurements allow documentation, analysis and diagnosis of machine tool travel and parallel axes of motion.
-
Product
RANGER-ULTRA
-
The RANGER-ULTRA is an airborne laser scanner with an impressive combination of weight, range, accuracy and pulse rate. It is equipped with a unique forward and rear looking FOV designed to minimize laser shadowing and provide geometry on complex vertical structures on a single pass. With its wide field of view of 100 degrees and an extremely fast pulse repetition rate of up to 1.8 MHz, the RANGER-ULTRA is perfectly suited for high point density corridor mapping applications such as power line, railway track and pipeline inspection.
