Switching
Controls consisting of a mechanical or electrical or electronic device for making or breaking or changing the connections in a circuit. (www.cogsci.princeton.edu)
See Also: Switching Matrix, High Voltage Switching, Switching Matrices, Multiplexers, General Purpose Switch
-
Product
PXI 8 Slot BRIC 161x16 1-Pole (7 sub-cards)
40-560A-121-161X16
Matrix Switch Module
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high-performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
PXI 64x4 Matrix Module, 2-Pole, 2A, 60W
40-583-001
Matrix Switch Module
The 40-583 is a 256 crosspoint PXI matrix with dual pole switching. The module consists of a 64x4 matrix of 2-pole electro-mechanical relays with 2A current handling. The module is designed for switching medium voltage and power signals, typical applications include signal routing in ATE and data acquisition systems. The user signal connection is via a robust 160 pin DIN 41612 connector that is fully supported by the wide range of Pickering Interfaces cable and connector accessories.
-
Product
Dual 12x6 1-Pole High-Density PXI Matrix Module
40-520-304
Matrix Switch Module
The 40-520 family of high-density PXI matrices is available in 22 different configurations with up to 256 crosspoints. The choice of six bus widths (x16, x12, x8, x6, x4 and x2) enables competitively priced solutions using Pickering Electronics instrumentation quality reed relays. These relays offer very long life with good low-level switching performance and excellent contact resistance stability. Typical applications include signal routing in ATE and data acquisition systems.
-
Product
Wires and Pipe Locator
LKZ-720
-
*Detection of wires and cables (live or not)**detection of cables in ceilings, walls and floors,**detection of breaks in cables,**tracing cables in building installation,**locating power points and switches in buildings,**locating short circuits between leads,**tracing shielded cables,**tracing cables in metal ducts.*Identification of fuses on the distribution board.*Tracing underground cables.*Tracing conductive water and heating pipelines.*Non-contact detection of live cables.
-
Product
PXI Ultra High Density 64x4 2-Pole Matrix
40-533B-022
Matrix Switch Module
The 40-533B ultra high density matrix module is configured as 64x4 or 64x2 and is available in a choice of 1-pole and 2-pole reed relay formats. Typical applications include signal routing in Functional ATE and data acquisition systems. These PXI matrix modules are constructed using high reliability sputtered Ruthenium reed relays, offering >109operations to give maximum switching confidence with long life and stable contact resistance. Larger matrices may be constructed by daisy chaining the common signals from multiple PXI modules.
-
Product
Cable Assembly, 50-Pin D-Type, Male to Female, 1m HV, Exit Towards Pin 1
A050DM5-050DF5-HA100
Cable Assembly
50-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24 AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assemblies can be secured to the mating part by a screwlock. The 50-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
-
Product
High Frequency Synthesizer
HFS Series 1.25” x 1” x 0.25”
-
*Surface Mount Package *Broadband Designs Available *Optional Internal Reference *Optional Reference Detect Switch *Internal Reference Output Available *Off-the-Shelf Products Available
-
Product
PXI/PXIe High Density 2A Multiplexer, 4-Bank, 8-Channel, 4-Pole
42-614D-008
Multiplexer Module
The 40-614D-008 (PXI) and 42-614D-008 (PXIe) 4-bank, 8-channel, 4-pole multiplexers are part of the High Density 2A multiplexer module range available in 23 configurations (see 'Also in this Range' link above). All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
Product
2-CH Pulse-Train Motion Control EtherCAT Module
EPS-7002
-
ADLINK" s EPS slave system features modular design for flexible high channel density, rugged construction, easy maintenance, and intelligent performance, compatible with 3rd party EtherCAT products. Precise time-deterministic control enables I/O synchronization for critical applications, and FPGA and ARM technology allow users to fully monitor status of EPS modules and systems, including operating temperature and usage cycle of relay switching, as well as motion control status for general purpose motor drive control. In addition, the ADLINK EtherCAT configurator enables auto-scan and configuration across EtherCAT systems. The EPS" unique structural and electronic design supports hot-swappable function, reducing repair time, and the rugged construction and operating temperature range of -20°C to 60°C allow operation in the harshest environments.
-
Product
Relays & Coax Switches
-
Teledyne Relays offers high-performance relays designed to survive the rugged conditions required for oil & gas exploration, industrial control, and military & space applications. Teledyne Coax provides RF & Microwave switching solutions for SATCOM, military & space applications, test & measurement equipment, and ATE systems.
-
Product
EDFA
SOA1550-32(64)
-
Hangzhou Softel Optic Co., Ltd.
*Single/dual input for choice, built in optical switch for dual input, the switching power can be set by the button in the front panel or by web SNMP.*Output adjustable by buttons in the front panel or web SNMP, the range is down 4dBm*Maintenance function of one-time downward attenuation of 6dBm by buttons in the front panel or web SNMP, to facilitate the optical fiber hot-plug operation without turn off the device*Multi- ports output, can built in 1310/1490/1550WDM.*Standard RJ 45 port for remote control, we can provide output contract and web manager for choice, and also plug-in SNMP hardware can be reserved for update.*With laser key to turn on/off the laser.*With RF test function.*Adopts JDSU or Oclaro Pump laser*Led displays the working condition of the machine*Dual power hot plug power supply for choice, 90V～250V AC or -48V DC
-
Product
PXI/PXIe High Voltage Multiplexer, Single 48-Channel, 1-Pole
42-321-109-HI
Multiplexer Module
The 40-321-109-HI (PXI) and 42-321-109-HI (PXIe) are single 48-channel 1-pole high voltage multiplexers capable of hot or cold switching up to 1000 V peak. They are also available in a range of bank sizes with 1 or 2 poles and channel counts between 4 and 48. High quality reed relays are used throughout.
-
Product
PXI/PXIe High Density Electro-mechanical Relay Module, 50xDPST
42-146A-202
Relay
The 40-146A-202 (PXI) and 42-146A-202 (PXIe) 50xDPST relay module is part of a range of high density switching modules available in Normally Open (SPST & DPST), Changeover (SPDT) and Normally Closed (SPST) configurations. Connections are made via a front panel 200-pin female connector.
-
Product
PXI 2 A Relay Module, 80xSPST
40-139A-101
Relay
The 40-139A-101 (PXI) and 42-139A-101 (PXIe) are 80xSPST relay modules suitable for high density switching applications with medium power and feature 2 A current capacity with voltage rating to 300 VDC/250 VAC
-
Product
3U VPX Dual-Plane Gen3/4 PCIe & 40 Gigabit Ethernet Switch
ComEth4420e
-
The ComEth4420e is a cutting-edge hybrid managed switch combining PCIe Gen3/4 and 10/40 Gbs Ethernet technologies. It has been developed in alignment with the SOSA (Sensor Open Systems Architecture) Technical Standard.
-
Product
Connection Units
-
Leuze electronic GmbH + Co. KG
All peripheral devices – such as sensors, safety switches and cameras – require a connection to the fieldbus or a control unit. Depending on device type and area of application, our modular connection units offer variable interfaces that enable simple connection of the devices directly to the fieldbus and thus ensure simple integration of new devices in the system.
-
Product
PXI Solid State MUX, 2 bank, 80 channel
40-680-005
Multiplexer Module
Based on FET switches, the multiplexers have no wear out mechanism and include fault protection that ensures the multiplexer automatically disconnects when PXI power is not applied. Available configurations for the 40-680 range vary from a single 160 to 1 MUX to a 20-bank, 8 to 1 MUX in a single PXI module.
-
Product
PXI 8 Slot BRIC 50x32 1-Pole (10 sub-cards)
40-562A-121-50X32
Matrix Switch Module
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8-slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
PXI/PXIe Power Relay Module, 16xSPDT, 5 Amp, 50-Pin D-type Connector
40-158-103
Relay
The 40/42-158-103 is a PXI/PXIe high density power relay module with 16xSPDT switches rated at 5A. User connection is via a 50-pin D-type male connector. The 40/42-158 range is available in 8, 16, 24 or 32 SPST configurations with or without hardware interlock. Electro-mechanical power relays are used which are suitable for switching loads up to 5A at 250VAC.
-
Product
LXI 8:1 Optical MUX SC/PC Single Mode
60-850-211
Multiplexer Module
Fiber optic multiplexers that use MEMS switching technology to ensure fast and reliable switching
-
Product
SS Body Vacuum Switch (longbody, NEMA 4)
P117LV
-
The P117LV NEMA 4 Stainless Steel Vacuum Switches are the weather-proof, liquid-resistant version of the P117V. The NEMA 4 rating makes these rugged switches suitable for outside applications or in areas of condensing humidity. Unlike the P117V, the P117LV set point is factory set to customer specification and is non-adjustable.
-
Product
PXI Fault Insertion Switch, 7-Channel, Two Fault Buses, 20 A
40-194A-002
Fault Insertion Unit
The 40-194A-002 is a 7-Channel Fault Insertion switch with two fault buses, designed for the simulation of fault conditions in automotive systems. As well as high current handling of 20A, very low currents can also be switched.
-
Product
Chassis Mounting Kit
63-924-001
Mounting Kit
This chassis mounting kit is designed for use with the our 8-slot PXI chassis (40-924) and our 7-slot LXI modular switching chassis (60-102D), allowing installation into a standard 19" rack.
-
Product
PXI 12x4 Matrix, 2 Pole Switching
40-510-022
Matrix Switch Module
The 40-510 series of matrix modules feature a wide range of selectable switchingconfigurations (12x4,dual 12x4,12x8 and 24x4). Typical applications include signalrouting in ATE and data acquisition systems.Available reed relay formats are 1-pole, 2-pole and 1-Pole screened. The screenedversion is suitable for switching signals up to 50MHz. Larger matrices may be constructedby Daisy Chaining the common signals from multiple PXI modules.
-
Product
Ethernet/LXI digitizerNETBOX 16 Bit Multi-purpose Digitizer - 20 MS/s on 40 Channels
DN6.592-40
Digitizer
The digitizerNETBOX DN6.59x series allows recording of up to 48 synchronous channels with sampling rates of 20 MS/s up to 125 MS/s. These products offer outstanding A/D features both in resolution and speed as a remote instrument. The powerful A/D amplifier section offers 6 different input ranges, programmable offset and a software switching from single-ended (full number of input channels) to true differential (half number of input channels).
-
Product
PXI 10A Power MUX, 2-Bank, 16-Channel
40-661-003
Multiplexer Module
The 40-661 is a single pole power multiplexer module, suitable for switching inductive/capacitive loads up to 10A with 125VDC/250VAC hot switching and 400VDC/250VAC cold switching. The multiplexer is available in 8-bank 4-channel, 5-bank 6-channel, 4-bank 8-channel, 2-bank 16-channel and 1-bank 32-channel formats. Also, 4-bank 4-channel, 2-bank 8-channel and 1-bank 16-channel half density configurations are available. Signal connections are made via front panel mounted 20-way GMCT plugs.
-
Product
PXI Octal SPDT RF Switch, 8GHz 50Ω SMA, Terminated
40-880A-004
RF Switch
The 40-880A-004 is an octal SPDT 50Ω RF switch with 8GHz bandwidth. The 40-880A range of SPDT switches have automatic termination of unused signals and are available as a dual switch in a 1-slot PXI module, a quad switch in a 2-slot PXI module or hex and octal switches in 3-slot PXI modules.
-
Product
Chassis - up to Sixteen 8x1 Modules, Thirty Two 4x1 Modules or Any Combination or Configuration of 8x1's, 4x1's, 2x1's and 2x2 Modules
CXAR/128-MF
Chassis
These Chassis controls up to sixteen 8x1 modules, thirty two 4x1 modules or any combination or configuration of 8x1's, 4x1's, 2x1's and 2x2 modules. LEDs on the front panel show switch and power status. Add Switch Modules, CP8 Driver Modules and a Control Module to complete the system. Keypad Manual manual control with LCD display is optional.
-
Product
Programmable Encoders
-
Free programming of pulse number, output level, SSI absolute value settings or switching speed. For end users, wholesalers and system integrators. Wide and versatile application possibilities. Reduced inventory variation, downtime, maintenance and storage costs
-
Product
Power Switching Devices
-
Watlow Electric Manufacturing Company
Watlow solid state power switching devices complement the rapid switching required by PID temperature controllers and help deliver optimum system performance and service life. They are available in 1-phase and 3-phase/2-leg and 3-leg configurations, feature touch-safe terminations, input indicators, zero-cross, random or phase-angle fire options, ratings from 18 to 1,000 amperes and agency approvals including CE and UL® 508. Various configurations offer short circuit current ratings (SCCR) of 200,000 amperes, extensive system and heater diagnostic capabilities, heater bake out, integrated heat sinks, on-board fuses, RoHS compliance and serial communications.
