-
Product
PXI 4 Slot BRIC 276x8 Dual Analog Bus (6 sub-cards)
40-560A-021-276X8-M
Matrix Switch Module
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high-performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
1pps-Locking-Modules
-
This is a module to control an OCXO or Rubidium oscillator with 1PPS from a GPS receiver. The Quartzlock A6-1PPS uses a 3 state Kalman filter algorithm to measure & correct the frequency offset of the oscillator with respect to the 1PPS input. Time-tagged input 1PPS to 200ps resolution & <1ns jitter. Analog interpolator is self calibrating. Interface to GPS decodes messages & extracts relevant info. i.e. time correction data for 1PPS output, this has AVAR of the Rb or OCXO i.e. 5 x 10-12/s & <100ps RMS jitter. The output is steered to time coincidence with GPS time/UTC to 1ns resolution. Holdover initiated by 1PPS fail or data from GPS RX that 1PPS is inaccurate. During holdover, measured frequency offset & drift steer the oscillator & 1PPS is still available.
-
Product
PCIe-5774, 12-Bit, 6.4 GS/s, DC-Coupled, 2-Channel PCI FlexRIO Digitizer Device
785650-02
FlexRio Digitizer
The PCIe-5774 is a PCI FlexRIO Digitizer Device that provides up to 3.2 GHz of DC-coupled analog bandwidth and 12 bits of resolution. You can operate the PCIe-5774 in a dual-channel mode at 3.2 GS/s or in a single-channel interleaved mode at 6.4 GS/s. The voltage ranges are software-selectable and include 200 mV peak-to-peak and 1 V peak-to-peak, with a selectable DC offset.
-
Product
cDAQ-9191, 1‑Slot, Ethernet and 802.11 Wi‑Fi CompactDAQ Chassis
781497-01
Chassis
1‑Slot, Ethernet and 802.11 Wi‑Fi CompactDAQ Chassis - The cDAQ‑9191 is a Wi‑Fi chassis designed for small, remote, or distributed sensor measurement systems. The chassis controls the timing, synchronization, and data transfer between C Series I/O modules and an external host. You can use this chassis with a combination of modules to create a mix of analog I/O, digital I/O, and counter/timer measurements. You can send data from the cDAQ‑9191 to a host PC over Ethernet or IEEE 802.11 Wi‑Fi. The chassis also has four 32‑bit general‑purpose counters/timers built in. You can access these counters through an installed, hardware‑timed digital C Series module for applications that involve quadrature encoders, PWM, event counting, pulse train generation, and period or frequency measurement.
-
Product
Sync Generator
LT4611
-
This product is a 1U full-rack size sync signal generator that outputs analog video sync signals and audio word-clock signals for broadcast stations. The external sync signal genlock function allows synchronized operation with input signals.The genlock function has a stay-in-sync function that maintains the phase when an error occurs in the input analog video sync signal. The dual power supply unit provides redundant operation. These features make it possible to configure a highly reliable system.Further, numerous options are available to allow GPS synchronization and PTP synchronization as well as arbitrary pattern output and digital audio output using 12G-SDI, 3G-SDI, HD-SDI, and SD-SDI. These options are designed to enable the management of the optimal synchronization system for your application.
-
Product
Analog Temperature Sensors
-
Analog Devices analog temperature sensors provide current or voltage output proportional to the absolute temperature with accuracies of up to ±1°C. Our diverse range of analog output temperatures sensors can be used in a broad range of applications with no need for external calibration, and with minimal signal conditioning/conversion circuitry. To better suit your varied design needs, our portfolio of temperature sensors are available in multiple package options.
-
Product
6GHz Single Channel Portable Signal Generator
LS6081P
Signal Generator
The LS6081P, 6GHz Single Channel RF Analog Signal Generator, offers industry leading performance, in a modern tablet like design that can be used as a benchtop or portable unit. The LS6081P features exceptionally fast switching speed, superior signal integrity and purity and all the necessary modulated signals for analog communication systems. The LS6081P was designed to offer excellent performance and meet today’s most demanding applications, whether in the lab or out in the field.
-
Product
PLC Input Modules
-
The DATEXEL DAT6000 series is a unique device designed to add analog inputs to a digital PLC with a few simple instructions. Downloaded into a standard PLC it is possible to acquire analog signals. The PLC will be able to read a 16 Bit digital input equal to the analog signal. The input, output and power supply are isolated from each other. The DAT6000 can linearize , filter and convert the input signal.The DATEXEL DAT6011 converts two voltages -50 mV to 50 mV, -100 mV to 100 mV, -500 mV to 500 mV or -1000mV to 1000mV or thermocouples K Type, J Type, S type, B type, R type, E type, T type and N type to a digital PLC.
-
Product
Read-Write Analyzers
-
Guzik Read/Write Analyzers (RWA) work in conjunction with Spinstands to write data to the disk media and read back the signal for detailed analysis. We have two RWA-4000 series available for For Two Dimensional Magnetic Recording (TDMR) and non-TDMR technologies. The RWA 4000 series offer upto 8Gbit/sec maximum write data rate and 3.5 GHz analog bandwidth for all parametric measurements. Each RWA features a pattern generator with 1psec resolution of bit pre-compensation and supports PRML chip integration. Servo writing and processing is provided for Guzik Spinstand models. Select the pre-amplifier (UP14) as well as a variety of enhancements including programmable filters and PRML chip adapters.
-
Product
Universal Test System
LEON System
Test System
A universal ICT, FCT, ISP and Boundary Scan platform.Based on the ABex platform, which directly integrates Konrad analog bus technology and PXI/PXIe in one chassis, the LEON platform can be configured to solve various test challenges. Due to this architecture only one system provides the complete test flow combining ICT, ISP, Boundary Scan and FCT.Various form factors and configurations allow a perfect combination between cost, speed and test coverage. The modular architecture provides the possibility to reconfigure or upgrade the systems based on your test needs.The LEON System software provides a powerful development and test execution environment which directly supports NI TestStand. All systems and components could be integrated into third party software using supplied APIs.
-
Product
PXIe-7962, Virtex-5 SX50T FPGA, 512 MB DRAM PXI FPGA Module for FlexRIO
781206-01
FPGA Module
Virtex-5 SX50T FPGA, 512 MB DRAM PXI FPGA Module for FlexRIO—The PXIe‑7962 provides flexible, customizable I/O for LabVIEW FPGA. It includes 132 single-ended I/O lines configurable as 66 differential pairs. You can pair the PXIe‑7962 with FlexRIO adapter modules that offer high-performance analog and digital I/O. Together, the two modules create a reconfigurable instrument that you can program with LabVIEW FPGA software. The PXIe‑7962 supports peer‑to‑peer streaming, which directly transfers data among multiple FPGA modules or select PXI Express modules without sending data to the host processor. With this feature, you can add FPGA capabilities to high-performance NI digitizers with NIST‑traceable calibration or expand your FPGA algorithms across multiple FPGAs for computationally demanding applications.
-
Product
Analog RF Slot Downconverter: 2000-2400 MHz Input
Model 8111-005
-
The Bandit® Model 8111 provides a series of high-performance, stand-alone analog RF slot downconverter modules. Packaged in a small, shielded enclosure with connectors for easy integration into RF systems, the modules offer programmable gain, high dynamic range and a low noise figure.
-
Product
Analog Clamp Meter
-
Operation0C~ 40C(32~104)/<80% R.H.(no condensation) Storage-10C~ 50C(14~122)/<70%R.H.(no condensation) Dimension & Weight 243(L)x91(W)x45(H)mm Approx.360g (Including battery) Accessories Battery UM-3 (AA) 1.5V x1 Instruction Manual x1 Test Lead (red + black) x 1 Carrying case x1 Optional Accessories Temp. Probe (NR-81) AC Line Splitter(DE-10ALS) *Applicable to electrical appliances small current
-
Product
ActiveX Controls for ADLINK DAQ/DAQe/PXI-2000 Series Cards (Vista Ready)
D2K-OCX
-
D2K-OCX ActiveX controls communicate with ADLINK data acquisition cards to perform digital, analog, and timer/counter operations. These ActiveX controls well-designed to hide all details of hardware manipulation so the data acquisition operations can be achieved by only few lines of codes. Furthermore, any hardware configuration can be done with the easy-to-use property pages, and the acquired data is returned in a event-driven manner.
-
Product
Power Meters
Rk-5700
-
The Rk-5700 Series Power Meters accept a wide variety of probes – pyroelectric, silicon, and thermopile – enabling them to perform absolute radiometry, total laser power (cw and average), and irradiance measurements from the UV to far-IR, pW to kW. Integrated lock-in amplifier circuitry allows for synchronous detection of chopped optical signals, improving both S/N ratio and background rejection. The dual channel Rk-5720 simultaneously measures Channel A, Channel B, and the ratio B/A. An IEEE-488 GPIB computer interface, Analog Outputs, Background Cancel, and Autorange are all standard features.
-
Product
20GHz Single Channel Portable MW Signal Generator
LSX2091P
-
The LSX2091P is a 20GHz Single Channel Microwave Signal Generator that offers industry leading performance, in a modern tablet like design that can be used as a benchtop or portable unit. It features exceptionally fast switching speed, superior signal integrity and purity and all the necessary modulated signals for analog communication systems. The portable design with a 10” touch screen offers excellent performance and meet today’s most demanding applications, whether in the lab or out in the field.
-
Product
USB-6363, 32 AI (16-Bit, 2 MS/s), 4 AO (2.86 MS/s), 48 DIO USB Multifunction I/O Device
782259-01
Multifunction I/O
32 AI (16-Bit, 2 MS/s), 4 AO (2.86 MS/s), 48 DIO USB Multifunction I/O Device - The USB‑6363 offers analog I/O, digital I/O, and four 32‑bit counters/timers for PWM, encoder, frequency, event counting, and more. Onboard NI‑STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The USB‑6363 is well suited for a broad range of applications, from basic data logging to control and test automation. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
Product
PXI 8 Slot BRIC 184x8 1-Pole Dual Analog Bus (4 sub-cards)
40-560A-121-184X8-M
Matrix Switch Module
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high-performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
Power Supply, 60 V, 85 A, 5,100 W
N8757A
Power Supply
The Keysight N8757A is a 60 V, 85 A, 5,100 W, single-output power supply in a small 2U package. It offers flexible AC input options, analog / resistance control of output voltage and current, and parallel and series connection of multiple supplies to achieve more output current or voltage.
-
Product
Magnetostrictive Level Transmitter
DM231
-
The Drexelbrook DM231 is an explosion proof liquid level transmitter offering high accuracy measurements based on the magnetostrictive sensing technology.The DM231 comes with a Modbus RTU digital output (optional analog output converter available) for total level, interface level and temperature sensor outputs. Sensors are available in 316SS rigid designs with a choice of single or dual NPT mountings. Temperature sensors are evenly distributed over the active length of the rigid 316SS tube.Due to a wide selection of floats and mounting accessories this level transmitter fits virtually any application.The DM231 level transmitter is FM approved for Class 1 Div. 1, Zone 1 Explosion Proof hazardous area installations. It is easy to install and requires no calibration.
-
Product
Pressure Meters
-
General's line of pressure meters and manometers. The top-of-the-line pressure meter is the data logging PM930SD Pressure Meter, which can measure up to 400 bar (5800 psi) when mated with an optional sensor. By comparison, the measurement range of the DM82XX family of manometers tops out at 100 psi. Also in this sub-category are the GPKXXX family of analog gas pressure test kits and the analog HG15 Hydrogage Manometer.
-
Product
HDTV PATTERN GENERATOR
HG139
-
The HG139 is an easy-to-use handheld video pattern generator that generates a wide variety of test patterns for comprehensive testing, calibration, and repair of HDTV, analog television monitors, and other video equipments. The HG139 delivers the quality and functionality you would expect from the expensive high end HDTV pattern generator at a very affordable price.
-
Product
PCI-5124, 150 MHz Bandwidth, 200 MS/s, 12-Bit PCI Oscilloscope Device
779171-01
Oscilloscope
150 MHz Bandwidth, 200 MS/s, 12-Bit PCI Oscilloscope Device—The PCI-5124 high-resolution oscilloscope device has two channels that sample up to 200 MS/s with flexible settings for coupling, impedance, voltage range, and filtering. Oscilloscope devices also feature a number of triggering modes, deep onboard memory, and an instrument driver that includes data streaming and analysis functions. This device is ideal for both time-domain and frequency-domain applications that require high-resolution measurements with up to 150 MHz of analog bandwidth.
-
Product
Ka-Band Silicon 5G Quad Core IC
AWMF-0108
-
The AWMF-0108 is a highly integrated silicon quad core IC intended for 5G phased array applications. The device supports four Tx/Rx radiating elements, includes 5 bit phase and 5 bit gain control for analog RF beam steering, and operates in half duplex fashion to enable a single antenna to support both Tx and Rx operation. The device provides 26 dB gain and +9 dBm output power during transmit mode and 28 dB coherent gain, 5.0 dB NF, and -28 dBm IIP3 during receive mode. Additional features include gain compensation over temperature, temperature reporting, Tx power telemetry, and fast beam switching using eight on-chip beam weight storage registers. The device features ESD protection on all pins, operates from a +1.8 V supply, and is packaged in a 48 lead 6x6 mm QFN for easy installation in planar phased array antennas.
-
Product
Probes & Meters To Monitor & Control PH/ORP
-
Digital and analog, combination probes, differential probes, mounting hardware and accessories.
-
Product
In-Circuit Tester
Sigma MTS300
-
The system is designed for high throughput; with up to 1,000 analog measurements per second it is one of the fastest test systems available on the market. Sigma test systems provide analog and digital In-Circuit Test capabilities, Vectorless Testing, Functional Test, Boundary Scan and On-Board Programming.
-
Product
Data Acquisition I/O Boards
-
General Standards Corporation is a leading supplier in data acquisition I/O boards, provides a complete family of data acquisition cards for sonar, industrial, and embedded applications on several form factors/busses, and for many operating systems. Functions available include analog I/O, serial I/O, and high speed parallel I/O.
-
Product
128-Pin Hybrid Driver/Sensor Module
HYB04
-
The HYB04 enables comprehensive analog as well as digital driver- and sensor-functions. It has 128 non-multiplexed hybrid pins per module.
-
Product
Analog Backplane Interface Board
MSXB 029
-
The Microstar Laboratories Analog Backplane Interface Board, part number MSXB 029, interfaces the Analog Backplane with a Data Acquisition Processor. The Analog Backplane Interface Board must be installed in the Analog Backplane to connect the backplane to a Data Acquisition Processor.
-
Product
Phase Meter
6000A
-
Clarke-Hess Communications Research
The Model 6000A Phase Meter replaces the very popular Model 6000. Using the latest digital techniques and optimally designed analog front end, the Model 6000A out-performs any other phase meter on the market today. It also does this at a remarkably low cost. The unit automatically selects the proper range for both amplitude and phase and is waveshape independent.
