Brinell Hardness Testers
test the indentation hardness of materials.
See Also: Hardness Testers, Leeb Hardness Testers, Rockwell Hardness Testers, Vickers Hardness Testers
-
Product
Insulation Tester
AD-2025
-
Measuring voltage control during measurement, Insulation measurement up to 400 G W. Elimination of trough resistance insulation ? 3 connectors measurement method, Autoranging, Auto-Discharge facility safely discharges the connected circuit after a test, 5 minutes, 1 minute at will shorter measurement,
-
Product
Measuring Devices for Magnetically Hard Materials
SF2
-
Electromagnet SF2 is a measuring circuits, which makes possible the generation of adequate values of static magnetic fields in air gap between the electromagnet poles, where the measured samples is placed. The range of magnetic field strength H amount from -1 650 to +1 650 [kA/m]
-
Product
Salinity Testers
-
Labodam pocket salinity testers are equipped with platinum sensors, providing fast and reliable results measuring the salinity of water and other low and high salt concentrated solutions. Equipped with replaceable electrodes, helping to reduce maintenance cost.
-
Product
Power Tester
PS-200
-
It is important to keep your graphic cards powered, but you want to make sure that your graphic cards aren’t overpowered. Not all power supply units have power surge protection, so your graphic cards may be vulnerable to damages from over voltage or over current. Protect your graphic cards now with the new PS-200.
-
Product
DIP Tester
Model DS-10
-
Putting it a conveyor to flow through a solder bath to obtain information needed to manage it. The created temperature profile makes it possible to monitor the 50ms sampling temperature of the preheat and solder temperature sensors in addition to the conventional management items.
-
Product
Power Tester
PS-228
-
The product designs with LCD to show ATX power voltage. Easy to plug with ATX power 20/24 pin and plug in (P4/P6/P8) to show the voltage on the LCD panel.
-
Product
Function Tester
-
Test device for functional testing of defibrillators, external pacemakers and ECG simulation.
-
Product
Leak Tester
LT-01
-
Jinan Leading Instruments Co., Ltd.
LT-01 Leak Tester is applicable in leak testing of pouches, bottles, pipes, cans and boxes of foodstuff, pharmaceutical, medical, daily chemistry, automotive, electronic components, stationary and other industries. It's also applicable in the leak testing of the specimens after falling tests and pressure resistance tests.
-
-
Product
CMP Tester
CP-6
-
The state of the art Rtec CMP tester CP-6 allows to study and characterize CMP process like never before. In addition to polishing wafers & substrates the tester comes with inline surface profilometer. This combinations sheds information on why and how the surface, friction, wear etc. changed. Tester also measures several inline parameters such as friction, surface roughness, wear volume etc. to understand the process in detail.
-
Product
Hard Disc Drive Connectors
-
Teledyne Impulse provides a broad array of disc drive connectors. Our connectors are RoHS compliant and are being used on most major platforms around the world. Teledyne offers its cone point technology to insure maximum connectivity performance, and high temperature plastic materials are common. Teledyne's products are designed to meet the global requirements of the computing industry. Custom design configurations are available upon request.
-
Product
Hipot Testers
Hypot® Series
-
The Hypot Series sets the standard for safety and efficiency in production line Hipot Testing. Whether your application requires AC Withstand tests, DC Withstand tests, or Insulation Resistance tests, The Hypot Series provides innovations that will allow you to begin achieving best practices for safety and efficiency without the need for an expensive automated test system or connection to a PC. You can even connect the Hypot Series with the HYAMP Series to form a seamless safety compliance system for Hipot and Ground Bond Testing.
-
Product
Hard Metric Eurocard Plugbord
8020
-
VECTOR Electronics and Technology, Inc.
3U x 160mm Eurocard size for 2mm Hard Metric connector. Pad-Per-Hole and peripheral bus both sides. Pad and bus surfaces not solder coated. Accepts cPCI 2mm J1 (25 row) & J2 (22 row) connectors on edge.
-
Product
PON Tester
-
Shanghai Grandway Telecom Tech. Co., Ltd
In order to effectively manage the user resources of FTTH, we have developed new generation products FOH-8PRO and FOH-100 to help operators complete the user resource management.
-
Product
Hipot Testers
95X Series
-
Vitrek built the 95X Series from the ground up with DSP technology – to bring you the safest, fastest, most capable, feature rich hipot testers available. The 95X Series combines high output power, with a wide range of AC & DC voltage outputs and extremely low leakage current measurement. Then we added a 4-wire milli-ohmmeter with dynamic range up to 100K ohms and an overlapping Tera-ohm class Insulation Resistance function. Top that off with an available 40 Amp Ground Bond capability and you’re just beginning to get a feel for what the Vitrek 95X Series Hipot Testers can do for you.
-
Product
Hipot Tester
STM/L
-
SafeTest Manufacturing/Luminaire (STM/L) can be used as a simple manual electrical safety tester or with varying degrees of automatic test sequencing.
-
Product
Leeb Hardness Testers
-
It is a type of non-destructive testing used to inspect large sized workpieces weighing above 1 kg.
-
Product
Rad Hard GaN Drivers
-
The space market has been driving towards more efficient power management solutions. Part of the drive includes the use of Gallium Nitride Field Effect Transistors (GaN FETs) for power conversion. GaN FETs have higher power conversion efficiency and have more natural immunity to radiation, due to them being wide-bandgap semiconductors. Equally important is the use of the correct driver that will allow reliable operation and maximize the benefits of the GaN FETs. Some of the key driver requirements are: a well-regulated gate drive voltage; high source/sink current capability and a split driver output stage.
-
Product
Continuity Tester
26200
-
Just clip lead to one end of wire in question. Probe other end of wire. If bulb lights up, there is continuity. If bulb fails to light the circuit is open. Not to be used on live circuits or computer sensor feed circuits.
-
Product
Relay Tester
-
Beijing GFUVE Electronics Co.,Ltd.
Assists in the inspection, installation, and repair of assigned electro-mechanical controls and equipment systems.
-
Product
Surge Tester
-
They are designed to detect quality defects in the insulation between winding turns, ensuring the reliability and performance of electrical components.
-
Product
Other Testers
-
Weshine Electric Manufacturing Co., Ltd
It is one of the important planned performance indexes for oil grade and quality identification. In practical application, theselection of suitable viscosity lubricating oil can ensure the normal and reliable operation of mechanical equipment. Thisinstrument is based on the national standard gb265_ The special testing instrument is designed and manufactured for measuring the kinematic viscosity of liquid petroleum products.
-
Product
Portable Hardness Tester with Printer
PHT-3500
-
State of the art, digital tester is designed to test the hardness of large hard metal parts. Loaded with useful functions and a built in mini-printer the PHT-3500 is clearly the industry leader for fast accurate hardness testing with advanced USB output and thermal printing capabilities.
-
Product
Cable Testers
-
Ningbo Betterbell Telecommunication Equipment Co, Ltd.
Suitable for testing the connection and seriation of 10-base-T(VTP/8TP)-AT 8C T258A.TIA568A/B. Token Rine and Vsoc4/6/8. This tester can be used conveniently, and can find connection fault easily and quickly.
-
Product
Insulation tester
-
The insulation resistance tester have these features with large LCD,backlight,holding data,Insulation resistance test with auto range,it has the construction of shakeproof ,dustproof ,damproof,and can be suitable for outdoor working environment,it apply to IEC 61010
-
Product
Leak Tester
DRK134
-
Shandong Drick Instruments Co., Ltd.
DRK134 Leak Tester is an advanced and intelligent tester designed according to related standard. It is applicable to test the seal property of flexible pack in food industry, pharmacy industry and daily chemical industry.
-
Product
Insulation Testers
-
Shenzhen Everbest Machinery Industry Co.,Ltd.
The insulation resistance (IR) test (also commonly known as a Megger) is a spot insulation test which uses an applied DC voltage (typically either 250Vdc, 500Vdc or 1,000Vdc for low voltage equipment <600V and 2,500Vdc and 5,000Vdc for high voltage equipment) to measure insulation resistance.
-
Product
Microhardness Tester
MT91 Series
-
Newage Testing Instruments, Inc.
The Newage MT91 System is an automatic microhardness testing system that uses the Rockwell method for the hardness result. Hardness is measured based on the depth of penetration rather than using an optical system to determine hardness based on the impression diameter.
-
Product
Peeling Tester
BN-3
-
Shanghai Dean Electrical Co., Ltd
Executive standard: GB/T4074.3-2008/IEC60851-3;Inspection standard: JB/T4279.6-2008Used to measure the film adhesion property of enameled round wires with nominal conductor diameter of 1.0mm and below;High-end SCM control is used;Set arbitrarily the number of twist;LED would automatically display the number of twists;Twist counter performs accurate and reliable counting;High-strength steel scraper would complete sample scarping at once, easy to operate and use.
-
Product
Polarity Tester
PT-1
-
International Electro-Magnetics, Inc.
The PT-1 provides a simple and easy way to determine the relative polarity of coil windings. It allows for an in-process test that takes a minimum of time to perform. By placing a coil on the platform and making connection to the start and end of a winding, a test signal is induced in the winding. The induced signal is low level and completely safe for the operator. By comparing the test signal phase of the coil under the test output, the relative polarity is indicated by the Red/Green LED. The tester operates by inducing a signal voltage in the coil under test by means of a magnetic flux field. The field is generated by a coil located in the probe base. The coil configuration is designed to provide optimum field distribution. We have also applied this basic circuit to a 5-channel scanning unit.
