Simulation Testing
See Also: Simulation, Simulators, Simulation Software
-
Product
Laser Diode Reliability Burn-In / Life-Test System
58602
Test System
Chroma 58602 is a high density, precision multi source measurement Unit (SMU) module with temperature control and exchangeable interface developed for burn-in, reliability and life test of optoelectronic components including laser diodes, VCSELs, VCSEL Arrays, silicon Photonics, photo-diodes and other similar components.
-
Product
Functional Test for Engineering Lab
Spectrum BT
Functional Test
Designed to meet the needs of product engineering labs, production lines, test development centers, and repair depots, the Spectrum BT is a configurable and scalable functional test system. This focused system solves typical functional test coverage challenges throughout the defense/aerospace product life cycle—and it’s upgradable as test requirements evolve.
-
Product
Flexible Cable, 2.4 Mm To 3.5 Mm
85134H
Test Port Cable
The Keysight 85134H is a 62.9 cm (24.75 in) long1 flexible cable with a 2.4 mm female2 to 3.5 mm male connector. Cable frequency range is dc to 26.5 GHz with a return loss greater than or equal to 16 dB. Insertion loss is 0.31 * sqrt (f) + 0.2 (where f is frequency is GHz) for the test port connector and 1.8 dB at maximum frequency for the device connector. Phase stability of semi-rigid/flexible cables is characterized with a 90 degree bend using a 2.5 inch radius. Stability1 of the Keysight 85134H is less than 0.12 dB and phase is less than 0.13o * f + 0.5o, (where f is frequency in GHz).
-
Product
PXI/PXIe Battery Simulator Module, 6-Channel, Simplified Current Sink, 750 V Isolation
43-752A-901
Battery Simulator
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 6-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
-
Product
Manual Test System for ICT & ISP with Integrated ABex and up to 426 Test Points
LEON Fixture
Test System
The LEONFixture is the ideal ICT and ISP solution for small and cost sensitive applications. This manually operated test system combines optimal ergonomics with high performance, durability and precision, ensuring your investment over the long term. The LEONFixture features a test system integrated in a manual base fixture. The system is designed to be used with an Ingun ATS MA13 insert which could be customized by a lot of fixture houses all over the world.As part of the LEON Family, LEONFixture is based on the ABex platform which directly incorporates Konrad analog bus technology and PXI/PXIe in one chassis.
-
Product
PXI/PXIe Battery Simulator Module, 2-Channel, V/I Readback, Simplified Current Sink, 750 V Isolation
43-752A-913
Battery Simulator
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 2-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
-
Product
HTOL Test Systems
Test System
Our IOL & Power-Cycling systems increase measurement quality & throughput while simultaneously reducing the Total Cost of Test (TCoT) of an open platform. We focus on complete monitoring and precise temperature control for each device under test.
-
Product
Communications Test System for Frontline Diagnostics
CTS-2750
Test System
The CTS-2750 is designed using Astronics Test Systems’ proven Synthetic Instrumentation architecture. Featuring 23instruments, and both Automated and Standalone modes to test, record, and diagnose faults, the unit provides complete RF, Analog and Digital capabilities. The field-upgradeable, software-defined architecture features easy-to-use graphical user interfaces and enables testing with minimal operator intervention. Test Program Sets can be created easily using the included TestEZ® software suite.
-
Product
Functional Test
xUTS
Functional Test
Extend test to encompass copious test points and DUT varieties along with real-time, hardware-in-the-loop and other state-of-the-art instrumentation. extendedUTS (xUTS) is a custom product for high complexity functional test. Configured for the unique needs of a class of devices under test (DUTs), the xUTS employs our universal test system approach that combines the best open platform instrumentation and software along with mass interconnect technology.
-
Product
Parallel Electrode SMD Test Fixture, DC To 3 GHz
16196C
Test Fixture
The 16196C surface mount devices (SMD) test fixture offers excellent repeatability and usability, with accurate correlation up to 3 GHz. 16196 series fixtures are custom designed to fit specific SMD sizes (see table below), and provide repeatable DUT positioning with reliable contacts to enable stable measurement results - reducing the possibility of operator-induced error. Traditionally, SMD inductor evaluation up to 3 GHz has been difficult to implement - now with the 16196 series, it’s easy to perform accurate and repeatable measurements.
-
Product
Fixture Kit 600x455mm RCV 8-slot for 6TL34
AG588
Test Fixture
Stopper kit includedYAVCANCON2 for fixture identification not included
-
Product
VLSI Test System
3380D
Test System
The 3380D/3380P/3380 test system have 4 wires HD VI source and any-pins-to-any-site high parallel test (multi-sites test) functions (256 I/O pins to test 256 ICs in parallel) that can meet the upcoming higher IC testing demands.
-
Product
Benchtop Automated Functional Test
midUTS
Functional Test
Combining bench-top portability with powerful automated test functionality, the midUTS is an extremely versatile yet cost-effective solution for your electronics functional test needs. Comprised of high-performance commercial-off-the-shelf (COTS) instruments, along with Bloomy’s medium-density signal-routing PCBAs, a built-in or USB-connected PC, and a pair of high-integrity, production-grade cables connected to an adjacent benchtop fixture, the midUTS can be used in engineering for PCBA bring up, as well as scaled to manufacturing to perform high-volume PCBA and sub-assembly functional testing. It is also ideal for depot diagnostic test, debug, and repair of field returns. The two mass-interconnected cables connect the midUTS to as many as 320 test points on the unit under test (UUT), supporting an extreme wide variety of products using bed-of-nails as well as cable-connected UUT test fixtures. Most importantly, the midUTS helps you automate sequences of functional tests using NI TestStand and the Bloomy EFT Module for TestStand. This ideal balance between powerful features and affordable cost allow you to automate earlier in the product development lifecycle, substantially increasing product quality and minimizing time-to-market!
-
Product
PXI RTD Simulator Module, 8 Channel, PT100
40-263-401
Simulator
The 40-263-401 is an 8-channel PT100 RTD Simulator. The 40-263 range is a cost effective method of simulating PT100, PT500 or PT1000 RTDs. It supports 4, 8, 12, 16, 20 or 24 channels in one or two PXI slots. Also, channels are able to be set as short or open circuit to simulate faulty wiring to a sensor.
-
Product
PXI Functional Test System
U8989A
Functional Test
The TS-8989 PXI functional test system is an integrated, all in one switch, load and measurement system in a box for high voltage or current mechatronics functional test applications of up to 104 nodes and 40A current loads.
-
Product
80 DIOs, 8AIs, 8AOs JTAG Boundary Scan Resources Unit Expansion
YAV9JTAH
Test Fixture
80 DIOs8 Ais8 AOsCompatible with all JTAG vendors
-
Product
HV Test System for Patient Monitors
Test System
HV test enclosure for testing medical products (patient monitors). Insulated test booth with large space for DUT.3 different test nests for adapting different devices.Displays from patient monitors are checked. For this, insulation tests and leakage current measurements must be carried out. Ensuring the standard-compliant test. For the safety of the operating personnel, the test cell is electrically locked while the high voltage measurement is active.
-
Product
Noise Figure Analysis Using NI PXI RF Test Instruments
NI-RFmx Noise Figure
Test Instrument
Measure noise figure, gain, Y-factor, effective temperatures, hot and cold power, and moreOptimized calibration and measurement routines for multi-DUT test using Y-factor and cold sourceSupports the PXIe-5668R 26.5 GHz VSA, the PXIe-5698 26.5 GHz preamplifier, and VSTsDesigned for use with industry-standard noise sources such as the Noisecom NC346 Series
-
Product
PXI RTD Simulator Module, 12 Channel, PT1000
40-263-303
Simulator
The 40-263-303 is a 12-channel PT1000 RTD Simulator. The 40-263 range is a cost effective method of simulating PT100, PT500 or PT1000 RTDs. It supports 4, 8, 12, 16, 20 or 24 channels in one or two PXI slots. Also, channels are able to be set as short or open circuit to simulate faulty wiring to a sensor.
-
Product
Test Handler
M4841
Test Handler
High-Throughput Device Handler for Volume Production Testing of MCUs and DSPs.
-
Product
2m BNC Test Cable
16048D
Test Port Cable
The 16048D test leads extend the measurement port with a 4-terminal pair configuration. It provides a BNC female connector board to allow attachment of user-fabricated test fixtures.
-
Product
PCI Strain Gauge Simulator Card, 6-Channel, 350 Ohm
50-265-016
Strain Gauge Simulator
These cards simulates the operation of a range of strain gauges making them ideal for testing strain gauge meters and a wide variety of industrial control systems. They provide a simple way of replacing in house developed sensors with a low cost simulator having excellent performance that is easy to calibrate and use.
-
Product
PXI Test System Dev, Debug & Monitor Software
InstrumentStudio
Test System
InstrumentStudio is free application software that provides an integrated approach to interactive PXI measurements. InstrumentStudio helps you to unify your display, export instrument configurations to code, and monitor and debug your automated test system. You can view data on unified displays with large, high-resolution monitors, and then capture multi-instrument screenshots and measurement results.
-
Product
Digital Functional Test
CTS100i
Functional Test
Capable of performance testing to defined traceable standards, CTS100i is designed to test Military, Aerospace and Safety-Critical equipment. CTS100i is a cost-effective digital functional test system, available in single, dual and three bay versions.
-
Product
Regenerative Battery Pack Test System
17020E
Test System
Charge/discharge modes (CC, CV, CP)Power Range: 10kW / 20kW per channelVoltage Range: 60V/ 100VCurrent Range: 100A/200A/300A/400A/ 500A/600A/700A/800A per channelRegenerative battery energy discharge, efficiency 85%Channels paralleled for higher currentsDriving cycle simulationFast current conversion without current interruptHigh precision measurementSmooth current without over shootTest data analysis functionData recovery protection (after power failure)Independent protection of multi-channel
-
Product
Lower-Cost Small Footprint In-Circuit Test System
TestStation LHS
In-Circuit Test System
The TestStation LHS in-circuit test system is a lower-cost, small footprint, feature scalable version of Teradyne’s popular, award winning TestStation product family. Compatible with existing TestStation LH fixtures.TestStation LH features the voltage accuracy and backdrive current measurement embedded in Teradyne’s SafeTest protection technology for accurate, reliable and safe powered-up testing of new low-voltage software.
-
Product
Test System Optimized for High Throughput, Low Cost of Test for Single Site, Multi-site and Index Parallel Applications
ETS-88RF
Test System
Targeting the needs of power amplifier (PA) and front-end-module (FEM) semiconductor manufacturers, the ETS-88RF test system is aligned with the test challenges associated with these direct RF radio wave interface components. The precision with which the ETS-88RF can measure high-gain, wideband frequency performance, adjacent channel leakage and power supply efficiency makes this test system the most cost-effective alternative to bench set-ups. Teradyne routinely provides timely updates to a substantial library of RF Standards (such as 802.11xx and 3GPP) targeted for PA and FEM test.
-
Product
EBIRST 50-pin D-type To 2x8-pin Power D-type Adapter
93-005-236
Test Adapter
eBIRST is a range of USB controlled test tools capable of performing automated path resistance tests on Pickering Interfaces PXI, LXI or PCI controlled switching solutions. Each tool simply interfaces with the switching system's connector so a test can be run using the supplied Windows-based software.
-
Product
VLSI Test System
3380P
Test System
The 3380D/3380P/3380 test system have 4 wires HD VI source and any-pins-to-any-site high parallel test (multi-sites test) functions (512 I/O pins to test 512 ICs in parallel) that can meet the upcoming higher IC testing demands.
-
Product
PXI RTD Simulator Module 18 Channel PT100
40-262-001
Simulator
The 40-262 is a 3U PXI module range that supports 6 (in one slot), 12 or 18 (in two slots) channels of RTD simulation. Based on the design principles of our 40-260 PXI Precision Resistor, this RTD simulator module can provide a setting resolution of <8mΩ (PT100) or <90mΩ (PT1000) and a resistance accuracy of better than 0.1% on all channels.
