Simulation Testing
See Also: Simulation, Simulators, Simulation Software
-
Product
Tailor-Made to Simulate Low-Temperature Plasma Sources and Systems
Plasma Module
-
The Plasma Module is tailor-made to model and simulate low-temperature plasma sources and systems. Engineers and scientists use it to gain insight into the physics of discharges and gauge the performance of existing or potential designs. The module can perform analysis in all space dimensions 1D, 2D, and 3D. Plasma systems are, by their very nature, complicated systems with a high degree of nonlinearity. Small changes to the electrical input or plasma chemistry can result in significant changes in the discharge characteristics.
-
Product
Flex Socket Test Module
JT 2127/Flex Socket Test Module
Test Module
The JT 2127/Flex STM memory socket tester is a family of hardware adapters specifically designed for the testing of of PCB-mounted DIMM & SODIMM sockets using a JTAG/boundary-scan controller and supporting software. The testing of memory sockets has always been troublesome for test and production engineers using JTAG/boundary-scan systems. Even when it is possible to create memory writes/reads from a boundary-scan compliant access device on the UUT (Unit Under Test), the initialization process may fail leaving you with little diagnostics information. What’s more it can still be uncertain whether fault lays with the DIMM module itself or the socket. Using the new JT 2127-Flex system from JTAG Technologies you get pin-point diagnostics from a known-good test interface so you can be certain that your socket is soldered correctly.
-
Product
Test Benches
-
Atec has made test equipment throughout all of its 65-year history. Test benches for aerospace and energy uses represent a significant segment of our experience. Atec has produced test benches involving hydraulics, mechanicals, electromechanicals, electronics, pneumatics, motors, and digital automation. Atec test benches have performed for challenging measurements, factory production, problem analysis and component overhaul scenarios. Today, complex test benches have capable data acquisition, control and communication systems integral in their electronics. Atec’s ADAQ™ system, based on COTS components and software, is proven and popular in test bench applications. DCUs, ECUs, FADECs and earlier analog or mechanical control units are easily interfaced.
-
Product
16 Port Phone Line Simulator (FXS) Adv
SIM-16FXS-A
-
This unit has 16 analog phone lines (FXS) making it a perfect tool for testing VoIP gateways, IVR, modems, access servers, audio conference equipment or anything that requires phone lines. Telephone line simulator acts like a "telephone company in a box" providing dial tone, ring voltage and all advanced phone line features such Caller ID, Call Waiting, Call Hold, Three Way Calling and many others.
-
Product
Test Engineering
-
TestEdge engineers have an average of 17 years of engineering experience in test, packaging, and fixturing. This experience is across a wide spectrum of products, customers, and ATE platforms. We have experience in all of the following:Digital, analog, mixed-signal, RF Test programming servicesRemote test capability Semi-automatic test generation Automatic data collection and reduction High performance test fixturing Format independant vector translation High power testing with liquid cooling
-
Product
On-Site Testing
-
Radiometrics Midwest Corporation
At Radiometrics we understand that some products are just to big to bring to us. Radiometrics will travel to you and perform in-situ testing at your facility or your clients location.
-
Product
Test Labs
ART-MAN
-
ART-MAN uses 285 100% vector sensors per SAM phantom and 390 sensors in the flat body phantom to take accurate measurements based on state-of-the-art near-field theory.
-
Product
testing facilities
-
Ingenieurbüro Dr. Hillger Ultrasonic-Techniques
Mechanical scanning of the component is required for the automatic imaging ultrasonic testing technology. Depending on the test requirements, the size and shape of the component and the required cycle times, we offer different solutions.
-
Product
Hardness Testing
-
DeFelsko offers handheld digital hardness tests in compliance with two different recognized hardness scales: Shore and Barcol. Our PosiTector SHD Shore Hardness Durometer is available in both Shore A and Shore D scale to measure the indentation hardness of non-metallic materials. The new PosiTector BHI Barcol Hardness Impressor is ideal for measuring the indentation hardness of soft metals, harder plastics and fiber-reinforced plastics.
-
Product
Portable Testing
-
Whether you need handheld testers, digital hydrometers, ground fault detectors or discharge testing equipment, we offer the cutting-edge technology you need to stay ahead in managing and maintaining your power systems.
-
Product
Damped Oscillatory Wave Simulators
-
Suzhou 3ctest Electronic Co.,Ltd.
Damped oscillatory wave test system for new energy can produce repeatable transient on HV or medium voltage power cord, control line and signal line. It can meet the requirements of CE and CCC certificate. With internal three-phase five-wire high power CDN DOPN 69100T, it can conduct new energy test and high power load test with good reliability, stable performance and easy operation.
-
Product
Fiber Optic Network Simulators
SIM-2FON-25
-
Vconsole fiber optic network simulator is custom built portable unit intended to simulate installed fiber optic facilities. Vconsole will design and build custom unit exactly to customers specification. The enclosure is capable of housing an individual spool with up to 100km of fiber. We will build each unit to client unique needs with custom fiber types, lengths, and connectors. A full range of connectors are available including SC, ST, FC, and LC types. This product is ideal for latency testing, product development and training and educational needs.
-
Product
Bluetooth Tests
-
Devices that are equipped with Bluetooth® technology must, on the one hand, meet the respective country-specific regulatory test requirements, such as B. in accordance with FCC, ISED or CE, as well as test requirements of organizations such as the Bluetooth® SIG or the CTIA have to pass and meet in order to obtain market approval.
-
Product
Simulation Table
KRD61 6-DOF
-
KRD61 series 6-DOF simulation table is a closed-loop servo simulation platform consisting of six servo actuators and six sets of dedicated hinges connected at the top and bottom platforms respectively. By virtue of the telescopic movement of the six actuators, the upper platform moves in six degrees of freedom (X, Y, Z, α, β, γ), so various space motion attitudes can be simulated.
-
Product
6 Channel Function Generator / Flow Simulator
DP-cPCI-2601
-
DP-cPCI-2601 is a 6 Channel 2MS/s Waveform Generator with high frequency performance, versatility and compact size in an economical cPCI bus format. Signal output in the range of 10 mHz to 5 KHz with 14 bit vertical resolution makes this single slot, 6U-sized cPCI card a powerful solution to meet most demanding test stimulus.DP-cPCI-2601 uses Direct Digital Synthesis (DDS) technique to generate stable and accurate output waveforms down to 0.01 Hz resolution. DP-cPCI-2601 offers Sine, Square, Ramp, Triangle, Pulse as built-in wave shapes and user defined arbitrary waveform.DP-cPCI-2601 can frequency sweep any of its function outputs. User can sweep upwards using linear sweeps.
-
Product
Mouth Simulator
BO1032
-
As consumers demand smaller devices that produce better sound and need better microphones, you need to test your microphones using more than a simple 1kHz tone. Sweep tests require a good mouth simulator that can produce a sweep with a known steady SPL.
-
Product
Vibration Testing
-
AMERICAN TESTING LABORATORY tests electronic components and end use products for the defense, automotive, military, aerospace, commercial and government agencies.
-
Product
Testing Consumables
-
Solar Light offers a plethora of consumables for SPF and other testing requirements, including high quality Molded and Sandblasted PMMA Plates, Pre-Analyzed and Certified SPF and UVA Sunscreen Standards, Disposable Medical-Grade Pads, and long-life spare Xe Lamps for use with our state of the art Solar Simulators.
-
Product
Shock Test
-
Shock testing determines the ability of equipment to withstand the infrequent non-repetitive shocks encountered in handling, transportation, and service and to continue to function, where required. Also, shock tests verify that equipment will not detach from its mounting during these tests.
-
Product
Metallurgical/Metallographic Testing
-
A partial view of our Metallurgical examination areas, showing metallurgical microscopes with digital filar micrometers. These instruments, along with our cross-sectioning and polishing equipment, make the Optical Metallography facilities at Pacific Testing among the most extensive in the industry. In addition, these facilites are under the supervision of our Chief Metallurgist, with a Ph.D. in Metallurgy.
-
Product
Four Quadrant Power Amplifier For Simulation Applicaton
PAV30000
-
PAV Series Four-quadrant Simulation Power Amplifier based on linear power amplifier technology and integrated advanced technical performance and rich functions.
-
Product
E-Motor Testing
TITAN eDrive
-
The progressive electrification of the powertrains in the mobility sector makes it necessary to test the individual drive motor and its inverter on the test bench in addition to complete powertrain investigations. In addition, electrified drives are now being used in a wide variety of vehicles on land, water or in the air.
-
Product
Engine Simulator
MS 1118
-
Test Set-A calibration unit is a test jig is used to simulate parameters of Adour 804E and 811 engines of Jaguar aircrafts. It simulates current, voltage, speed, and turbine gas temperature. It performs NL Check, NH Check, TGT1 (Non T2 Compensated), TGT2 (T2 Compensated), Amp (Non T2 Compensated), Amp (T2 Compensated), Solenoid Volt, TGT Inject, NL Inject, and NL/TGT Redatum.
-
Product
Mobility Simulator Creates V2X Environments For Testing
MxDrive™
-
MxDrive is a multi-vehicle and infrastructure mobility simulator that provides an environment to generate and run real-world conditions to test connected vehicle applications. Testing V2X applications on actual roads has limitations. Only a limited number of test conditions can be achieved, while safety and damage risks further limit test coverage. MxDrive combined with the MxSuite ecosystem significantly simplifies the testing of Advanced Driver Assistance Systems (ADAS), Sensor Fusion, Radar, and V2X. MxSuite is ISO 26262 qualified to test safety applications for OEMs and suppliers.
-
Product
Material Testing & Physical Testing
-
Meeting the specifications put out by testing equipment manufacturers is critical when conducting quality control testing. We carry a wide variety of materials testing and physical testing products that are ideal for quality control testing along with research applications, letting you evaluate and test materials such as plastics, coatings, and chemicals. Physical properties testing products range from force and torque instruments, to hardness and thickness gauges, to viscometers and spectrometers.
-
Product
SMD Array Type LCR Test Fixture
16034H
Test Fixture
The 16034H is designed for impedance evaluations of array-type SMD.The minimum SMD size that this fixture is adapted to evaluate is 1.6(L)x0.8(W)[mm]. Since the tip of the measurement electrodes are very thin and the device holder is extremely flat, the device can be shifted and the measurement electrodes can contact each of the elements of the array-type component.
-
Product
Hi-Pot Testing
-
The CableEye HVX System combines our M3U tester with a high voltage module to provide Hi-Pot testing of insulation resistance and dielectric breakdown up to 1500Vdc and 1000Vac.
-
Product
Functional Testing
-
Interface Testingevaluation of correct system module interaction Smoke Testinginitial testing process to check whether software is ready for further testingSystem Testingconducted on a complete, integrated system to evaluate the system's compliance with its specified requirements Integration Testingperformed to test units of code to verify interaction between various software components and detect interface defectsRegression Testingtesting to ensure changes made are not impacting previously working functionality Acceptance Testingperformed to make sure the software handles required tasks in real-world scenarios, according to specifications
-
Product
Single Stream STANAG3910/EFEX Test & Simulation Module For 3U PXI Express/Compact PCI Express
ACE3910-3U-1
Simulator
STANAG3910/EFEX Test and Simulation module for CPCIe/PXIe (3U) with 1 Dual Redundant HS/LS channel. Onboard Fibre Optic Front End (FOFE). Easily select between EFAbus and EFEX modes for Tranche II Eurofighter.
-
Product
Multi-Parameter ECG Patient Simulator
SL-8 SimSlim®
-
The smallest, comprehensive multi-parameter patient simulator on the market. Includes ECG, Respiration, Arrhythmia, 4-IBP, YSI 400/700 Temperature, and Cardiac Output. Its patented power circuitry provides amazing battery life up to 10 years without charging or changing batteries! One button operation reduces the time for setup and completing testing. View the product manual on our User Manuals page.
