PCMCIA Interfaces
-
Product
PCIe-8431, PCI Express, 8-Port, RS485/RS422 Serial Interface Device
780592-01
-
The PCIe‑8431/8 is a high-performance interface for high-speed communication with RS485 and RS422 devices. It features high-performance DMA transfers, multithreading, and multiprocessor support. You can also select between … 4‑ and 2‑wire transceiver modes for full- and half-duplex communication. NI serial interfaces also appear as standard COM ports for compatibility with programs that use serial communications.
-
Product
Universal Plug-in Module With I/O And CAN FD Interface
PCAN MicroMod FD
-
The PCAN-MicroMod FD is a small breadboard with CAN and CAN FD connection on the one hand and various physical inputs and outputs on the other. Both sides are logically linked using the NXP LPC54618 microcontroller. Electronics developers can use the PCAN-MicroMod FD to easily integrate I/O functionality with a CAN connection into their project.
-
Product
DAS Trays/ Point-of-Interface (POI)
-
*CCI DAS Trays provide a common connection point to the DAS system for multiple BTS's*Modular design allows support for bands from 700MHz to 2700 MHz*Independent level control for each BTS for adjusting TX & RX power*Easy optimization features including separate Uplink and Downlink control*Can support both 0 dBm and +30 dBmDAS TX inputs (high and low power)*Supports NIMO and SIMO configurations
-
Product
CAN Sensor/ Interface
Current
-
Reach Technologies’ CAN Current Sensors sense and digitize conductor current for collection via CAN. The module is ideal for conveniently adding current data to a distributed CAN network. The CAN Current Sensor is configurable via J1939 or CANopen stacks, and are available in Hall Effect and shunt variants.
-
Product
cPCI Intelligent Interface Card
IIB-1553-CPC
-
The IIB-1553-CPCI is an intelligent interface card providing full MIL-STD-1553 test, simulation and bus analysis capability for the CompactPCI bus, with 1553A, 1553B, McAir and STANAG 3838 capability on a single card.
-
Product
Power Interface and Prototype PXI Card
GX7404
-
The GX7404 power interface board offers a low cost method for providing controlled power to UUT interface and test circuitry. The GX7404 provides +5 V, +3.3 V, +12 V, and -12 V voltage outputs which are present on the PXI motherboard to be switched through a DB25 connector for use by a UUT (unit under test) and / or interface circuitry.
-
Product
I2C Fast Mode Interface for USB 2.0, I2C Multimaster and Monitor
Connii MM 2.0
-
telos EDV Systementwicklung GmbH
Connii MM 2.0 is a small, compact, easy-to-use solution for a PC driven I2C transmitter and receiver. The I2C interface works as an I2C multimaster device. Thus, it is able to drive buses running multiple I2C bus masters. Additionally, Connii MM 2.0 is a limited I2C monitor for traffic up to 400kHz.
-
Product
Advanced ARINC-429 Testing Ethernet Appliance - Parametrics TX Variable Voltage, Digital Signal Generator and RX Signal Capture
ENET-A429P
-
eNet-A429P™ is an innovative product that provides “remoting” of ARINC operations on 10/100/1000 Ethernet IP/UDP local area networks (LAN). eNet-A429P is a small, low-power, device ideal for details ARINC signal testing with variable voltaqe control of the first 3 TX channels. Alta has combined the industry’s most advanced 32-bit ARINC FPGA protocol engine, AltaCore™, with a real-time IP/UDP thin server. The customer can implement their application with the same feature-rich application programming interface, AltaAPI™, as used with standard cards – often without even recompiling – the utlimate in code portability.
-
Product
Digital Backplane Interface Board
MSXB 033
-
The Microstar Laboratories Digital Backplane Interface Board, part number MSXB 033, interfaces the Digital Backplane with a Data Acquisition Processor. The Digital Backplane Interface Board must be installed in the Digital Backplane to connect the backplane to a Data Acquisition Processor.
-
Product
ARINC 429 Test & Simulation Interface for PCI
PCI-C429
-
Avionics Interface Technologies
4, 8, 16, or 32 Software Programmable Tx/Rx Channels - Programmable High/Low Speed Operation - Concurrent operation of all Tx/Rx Channels at high data rates - Full error injection and detection - Data capture filtering, 100% bus recording, and physical bus replay - Rate-oriented Label Transmission - Label Selective Trigger for Capture/FilteringIRIG-B time code encoder/decoder with free-wheeling modeApplication Interface supporting C/C++, C# and VB.NET Development - Device driver support: Windows, Linux (others on request) - Compatible with AIT’s Flight Simulyzer GUI Bus Analyzer Software
-
Product
Multiprotocol P104Plus Interface Board for Embedded Applications or Avionics Test & Simulation Applications
EXC-4000P104plus
-
The EXC-4000P104plus is a multiprotocol P104plus interface board for embedded applications or avionics test and simulation applications. Each board holds up to five independent modules. Two on-board modules use the MIL-STD-1553 communications protocol (M4K1553Px); another on-board module uses the ARINC-429 communications protocol; two additional detachable modules can be any one of the following types:M4K1553PxS (Single Function - RT validated) This module operates as a Bus Controller, Remote Terminal or a Bus Monitor. This module qualifies for airborne applications.M4K1553Px (Multi Function) This module operates as a Bus Controller, up to 32 Remote Terminals and as a Bus Monitor. Supports an Internal Concurrent Monitor in RT and BC/RT modes.M4K1553Px(S)-1760 Same as M4K1553Px(S) plus MIL-STD-1760 options.M4KMMSI Mini Munitions Store Interface module. Supports RT, BC/Concurrent-RT/Concurrent Monitor and Bus Monitor modes. Up to 8 hub ports EBR-1553 [10 Mbps 1553 protocol using RS-485 transceivers] and 1 monitor output.M4KH009 Based on our H009 family. This module operates as a Central Computer Complex (CCC) and/or up to 16 Peripheral Units (PUs) simultaneously, or as a Bus Monitor. In addition, a Concurrent Bus Monitor enables concurrent monitoring of the bus during CCC and PU simulation.M4K429RTx Based on our ARINC 429RxTx board. This module supports either five or ten ARINC 429 channels each of which can be configured in real time as a receive or transmit channel.M4K708 This module supports two channels of ARINC 708/453, each one selectable as either transmit or receive.M4KSerial This module supports up to 4 independent channels of serial communications, each of which can be selected as RS485, RS422 or RS232.M4KDiscrete This module supports 20 selectable input/open collector output discretes. The module supports TTL (0 to 5 volts) or avionics (0 to 32 volts) voltage levels.M4KCAN This module supports up to 6 independent channels of CAN 2.0B protocol with standard and extended message frames and message identifiers.
-
Product
PXIe-6593, FlexRIO High-speed Serial Module (16 Gbps), KU060
785977-01
-
PXIe, 16 Gbps, 8-Channel PXI High-Speed Serial Instrument - The PXIe‑6593 is designed for engineers who need to validate, interface through, and test serial protocols. It includes a Xilinx Kintex Ultrascale FPGA to implement various high-speed serial protocols, and it is … programmable in LabVIEW FPGA for maximum application-specific customization and reuse. The PXIe‑6593 takes advantage of FPGA multigigabit transceivers for up to eight TX and RX lanes.
-
Product
Isolated Four-Port Serial Interface Cards
PCI-ICM422-4 and PCI-ICM485-4
-
These cards can be installed in any 5-volt PCI-bus computer that can accommodate "long" cards and are designed to provide effective communication on long communication lines in noisy environments. The data lines are opto-isolated from the computer and from each other to assure communication even when large common mode noise and voltages are superimposed. Type 16550 UARTs are used. These include a 16-byte transmit/receive FIFO buffer to insure against lost data in multitasking operating systems. All ports are independently addressable and an on-board crystal-controlled oscillator permits precise selection of baud rates up to 115,200 baud or, by changing a jumper, up to 460,800 baud.
-
Product
VME Intelligent Interface Card
IIB-3910-VME
-
The IIB-3910-VME is a single slot (6U) intelligent interface card providing complete STANAG 3838 and STANAG 3910 test, simulation and bus analysis capability for the VME Bus.
-
Product
25 GHz differential probe with ProAxial interface
DH25-PX
-
25 GHz differential probe with ProAxial interface.
-
Product
Serial Parallel Interface
Model 2303
-
* 2303 Board provides 40 high-power TTL I/O lines that can sink 23 mA or source 24 mA. * Easily interfaces to TTL or CMOS signals and contact closures. * User can configure the data bytes as inputs or outputs.* Transfer data as bits, bytes as data strings or transparently.* Dual Serial headers support conections with baud rate switch inputs or to a Serial Flat Ribon Cable Assembly. * Optional Relay Driver board drives 24-40 relays. * 114732 Board has the DIN connector on circuit side for use with the X3DVR Relay Driver Board or for piggyback mounting.* All other specifications are the same as listed above for the 2303.
-
Product
Multi-Channel (Up to Four) MIL-STF-1760 Interface Board for Conduction Cooled PCI Mezzanine Card Compatible Computers
EXC-1553ccPMC/Px(S)-1760
-
The EXC-1553ccPMC/Px(S)-1760 is a multi-channel (up to four) MIL-STD-1760 interface board for conduction cooled PCI Mezzanine Card compatible computers. In addition, Checksum, SRQ bit and Header Words are supported on each channel. Multi Function:Each channel operates simultaneously as a Bus controller and/or multiple (up to 32) Remote Terminals, or as a Triggerable Bus Monitor. In addition, error injection (BC and RT modes), error detection (all modes) and cableless internal loopback are supported on each channel. Single Function:Each channel operates either as a Bus Controller, Remote Terminal, or Bus Monitor.Each dual redundant 1760 channel can operate simultaneously as a Bus Controller and up to 32 Remote Terminals and as a Triggerable Monitor. In addition, error injection (BC and RT modes), error detection (all modes) and cableless internal loopback are supported on each channel. The EXC-1553ccPMC/Px(S)-1760 is supplied with C drivers, including source code, and Merlin+ Windows software.
-
Product
PXI RS232 Interface Galvanic Isolation
PXI‑8432/4 - OTP2-Modul-Nr196
-
The PXI‑8432/4 module is a high-performance, dielectric-proof interface for high-speed communication with RS-232 devices. The module offers data transfers via the high-speed DMA interface, multithreading and multiprocessor support. NI serial ports appear as standard COM ports for compatibility with programs that use serial communications.
-
Product
H+W (Pylon) 1280 Point Test Interface
-
H+W (Pylon) 1280 Point Test SystemUp to eight positions for 160 Point Wiring Blocks.
-
Product
Ethernet Parallel Interface
Model 8013
-
* Provides 128 high-power TTL I/O lines.* Fully VXI-11 Compliant plus Raw Socket for easy programming with Visual Basic or C, Agilent VEE and LabVIEW.* Standard board has a horizontal Ethernet connector and 150-pin Digital IO connector on the component side. * Mates to Relay Driver Boards with 64 or 128 Relay Drivers.* Mates to 115650 Connector Board with 4 flat ribbon headers.
-
Product
Ethernet Digital Interfaces
-
All of ICS's Ethernet Digital Interfaces are user configurable and let you transfer data as bits, bytes, as strings of bytes or transparently. All data lines are high power TTL outputs or floating inputs with pullup resistors for sensing CMOS signals or switch contacts. All interfaces conform to the IEEE-488.2 Standard, are VXI-11 compatible and/or support TCPIP Raw Socket protocol.
-
Product
2-CH PCI ExpressR IEEE 1394b Frame Grabber
PCIe-FIW62
-
The PCIe-FIW62 is an IEEE 1394b (FireWire 800) interface card which provides two high-speed FireWire 800 ports with data transfer rates up to 800 Mb/s on a PCI ExpressR x1 lane. The PCIe-FIW62 provides two direct-connect IEEE 1394b bilingual connectors with a screw-lock mechanism. These screw-lock connectors provide a reliable connection between the PCIe-FIW62 and up to two IEEE 1394b cameras. A 4-pin ATX power connector on the PCIe-FIW62 supports IEEE 1394b cameras that draw power directly from the frame grabber. Each port has a green LED on the front panel that will illuminate when the PCIe-FIW62 is connected to a IEEE 1394b camera for convenient identification of channel connection status.
-
Product
Stand-Alone Programmer and Hardware Debug Interface
Cyclone MAX
-
Cyclone MAX is an extremely flexible tool designed for in-circuit flash programming, debugging, and testing of Freescale ColdFire V2/V3/V4, Power Architecture 5xx/8xx, Power Architecture 55xx/56xx (Nexus), and ARM (MAC7xxx) microcontrollers.
-
Product
PXIe-1486, 8 Input, 8 Output, or 4 Input/4 Output PXI FlexRIO FPD-Link™ Interface Module
787453-01
-
The PXIe-1486 combines the Texas Instruments Flat Panel Display Link™ (FPD-Link™) interface with the Xilinx FPGA for high-throughput vision and imaging applications. This module provides a … high-speed digital interface for using and testing modern advanced driver assistance systems (ADAS) and autonomous drive (AD) camera sensors and electronic control units (ECUs). Additionally, the PXIe-1486 makes use of a combination of FPD-Link™ serializers and deserializers with a Xilinx FPGA to provide a high-throughput and customizable FPD-Link™ interface on PXI. The included FlexRIO driver, with LabVIEW FPGA examples, provides access and control for power-over-coax, I²C back-channel communication, and general-purpose input/output (GPIO) communication on the FPD-Link™ channels. The PXIe-1486 is ideal for applications such as in-vehicle data logging, lab-based playback, or hardware-in-the-loop (HIL). FPD-Link is a trademark of Texas Instruments.
-
Product
sbRIO-9871, Non-Enclosed, 4-Port, RS485/RS422 C Series Serial Instrument Control Module
780879-01
-
The sbRIO‑9871 adds RS485/RS422 serial ports to CompactRIO systems. The serial ports are accessed directly from the FPGA to offer you flexibility in communicating with serial devices. The module has individual buffers on every port that save FPGA space and simplify programming. The sbRIO‑9870 supports standard start bit, stop bit, and handshaking settings. It uses an external power to provide maximum compatibility and reliability under all serial port conditions. Non-enclosed modules are designed for OEM applications.
-
Product
48-Channel DIO (Digital Input/Output) PCMCIA Card
D480C/i(DIOi480)
-
The D480C/i offers up to 48 separately controllable Digital I/O lines for general purpose control and monitoring applications.
-
Product
Interface Technology Style VXI Module Shield Kits
-
*Encloses Interface Technology style, slotted-edge, C-size PC boards All kits include side shields, a pre-machined blank front panel, ejector handles, all necessary hardware and assembly instructions. * All kits are available with customized front panels and side shields.
-
Product
Conduction Cooled XMC Interface Board with PCI Express Host Interface, Supporting up to 4 PX Modules, 2 RTx 5 Channel Modules, 1 Discrete & 1 Serial Module
EXC-8000ccXMC
-
The EXC-8000ccXMC is part of Excalibur’s 8000 family of multiprotocol boards. This conduction cooled XMC interface board has a PCI Express host interface and supports up to 4 Px modules, 2 RTx 5 channel modules, 1 Discrete and 1 Serial module. Due to the constraints of the XMC specification the modules are integrated onto the board itself rather than as physically separate modules.The EXC-8000ccXMC supports Direct Memory Access (DMA), which enables the board to access system memory for reading and writing independently of the computer’s CPU. This results in faster data transfer to and from modules that support DMA, with much less CPU overhead than when not using DMA.
-
Product
4 or 8 ARINC Channels in In-Line USB SuperSpeed Cable
NLINE-UA429
-
NLINE-UA429™ is an innovative product of ARINC operations for USB connections, ideal for in-field applications or point-point lab usage.
-
Product
3U Conduction Cooled Power Interface Board, VITA 62
106PIBV301-0000R
-
3U Conduction Cooled VPX Power Interface Board, VITA 62 compliant. Power Interface Boards (PIBs) facilitate the use of pluggable power supplies and headers with the power section of the backplane.
