Control Systems
-
Product
Automatic Power Control system
-
The Automatic Power Control system cuts the incoming power supply to a traction unit for short periods. This is required where power supplied from one part of a power distribution system in separated from another by a neutral section. Its fitment prevents damage to the power distribution system or the vehicle.
-
Product
OPC UA Gateways
-
OPC UA protocol gateway features upgradeability and compatibility and is widely used in control systems - MES and ERP.
-
Product
PXI Resistor Module 4-Channel 1R to 510R
40-293-014
Programmable Resistor Module
The 40-293 is a Programmable Resistor module with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Flight Control System Test Platform
Test Platform
The Flight Control System Test Platform provides a hardware in-the-loop (HIL) closed-loop test environment for dynamic and maintenance testing of Flight Control Systems (FCS) of both commercial and military aircraft. The system simulates control surface activities from multiple combinations of rudder, flaps, elevator, aileron, and engine controls to the FCS. The system delivers repeatable, cost-effective testing in a fraction of the time needed with typical in-house simulation test systems.
-
Product
PXI Programmable Resistor Card 2-Channel 2.5 Ohm to 4.09k Ohm
40-294-023
Programmable Resistor Module
These PXI Programmable Resistor modules are available with either two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
21 Slot, 3U PXIe Chassis
GX7200 Series
Chassis
The GX7200 Series mainframes are 21-slot PXI chassis that can accommodate up to 20 instruments as well as a PXI Express controller (an embedded CPU or a PXI bus expander interface such as the MXI). The backplane architecture supports Gen 2 PCI Express bus signaling and the use of both x1 or x4 system controllers. By offering a combination of PXI-1, Hybrid, and Express slots, the GX7200 offers users the ultimate in flexibility for general purpose as well as high bandwidth test needs.
-
Product
General Purpose Surface Temperature Assembly
S2-2
-
The Series S2-2 General Purpose Surface Temperature Assembly is ideal for monitoring the temperature of indoor distribution lines when it is not possible to penetrate the pipe. The plastic housing is in the shape of a standard junction box with multiple knockouts for easy conduit access. The strap-on connection quickly wraps around a pipe and can be securely tightened using a flat head screw driver. The Series S2-2 can be ordered with a choice of 11 output options that allow it to communicate to any standard building control system
-
Product
Structural Health Monitoring System
SHM
-
Automated stationary structural health monitoring system (SHM) is a subsystem of buildings and structures control system which has been developed in accordance with the applicable requirements of the corresponding standards. It is used to detect a transition of the building state from operational into the state of failure, that may eventually lead to fatal accidents.
-
Product
Automated Visual Control System for Canned Food in Glass Containers
-
The system is designed for visual quality control of food packaging products. The level of filling the jar with the product, as well as its closure, is monitored. During the development of the system, smart cameras from Sick were used, but a special illumination of our design was used to improve the image quality.
-
Product
PCI Strain Gauge Simulator Card, 4-Channel, 2k
50-265-304
Strain Gauge Simulator
These cards simulates the operation of a range of strain gauges making them ideal for testing strain gauge meters and a wide variety of industrial control systems. They provide a simple way of replacing in house developed sensors with a low cost simulator having excellent performance that is easy to calibrate and use.
-
Product
PXI-2512, 7-Channel, 10 A PXI Signal Insertion Switch Module
778572-12
Signal Module
7-Channel, 10 A PXI Signal Insertion Switch Module—The PXI‑2512 fault insertion unit (FIU) is designed for hardware‑in‑the‑loop (HIL) applications and electronic reliability tests. Each module has a set of feedthrough channels that you can open or short to one or more fault buses. You can use this architecture to simulate open or interrupted connections as well as shorts between pins, shorts to battery voltages, and shorts to ground on a per-channel basis. When controlled with the LabVIEW Real-Time Module, the PXI‑2512 is ideal for validating the integrity of control systems including engine control units (ECUs) and full authority digital engine controls
-
Product
Superior Electromechanical Universal Testing Machine
WDW-S Series
-
Jinan Testing Equipment IE Corporation
WDW series computer control electromechanical universal testing system for tension,compression, flexure testing is designed according to ASTM, ISO, DIN, EN standards etc.. The electromechanical universal testing system for tension,compression, flexure testing is computer-controlled and precision. Our electromechanical universal testing system for tension,compression, flexure testing is widely suitable for metallic and nonmetallic materials for tension, compression, bending, shearing and low cycle test. The electromechanical universal testing machine features high precision, high stability and high reliability. Graph, test result display, data processing and printing can be done easily by its PC system and printer. Completed with modulus for metal, spring, textile, rubber, plastic and other material test, the electromechanical universal testing system for tension,compression, flexure testing is widely used in many fields such as industry factories, research and development, test institutes and training centers etc. WDW-S series superior materials testing systems adopt robust load frames, precise load weighting system, advanced measuring and control system, and intuitive modular application software. Configured with wide range of accessories for applications, the materials testing systems can provide the best testing solutions for your individual application needs. With 20 years’ experience of materials testing industry and based on abundant application knowledge, we are completely capable of configuring the best solutions and more accurate testing systems for the manufacturers involved in load frame, core measuring and control elements, software package, grip/fixture that based on their specified test application and other requirements.
-
Product
128 Channel Digital I/O Modular PXI Card
GX5733 Series
Digital I/O
The GX5733 is a 3U modular digital I/O card that offers up to 128 I/O channels. Designed for ATE, data acquisition, or process control systems where a large number of discrete I/O channels are required, the GX5733 offers the highest channel density and flexibility in the industry for a single-slot, 3U PXI plug-in board. 96 channels support TTL levels and an additional 32 I/O channels can be customized by installing one of Marvin Test Solutions' GX57xx series I/O modules. Alternatively, the remaining port can be configured to support 32 TTL channels.
-
Product
System Modeling
-
Mentor Graphics SystemVision is a mixed-signal modeling and simulation environment using the power of VHDL-AMS and SPICE to verify your control and mechatronic systems. SystemVision includes graphical design entry, VHDL-AMS modeling and library tools, leading-edge simulation technology and powerful waveform viewing and analysis tools
-
Product
High-Resolution VMEbus Laser Axis Board
10897D
Laser Board
The 10897D High-resolution VMEbus laser axis board provides excellent resolution of up to 0.3 nm with a high resolution interferometer. The data age uncertainty is dramatically reduced allowing extremely accurate measurement and control of moving systems. The very high data rates accommodate high-bandwidth and high-performance closed-loop applications. Configured with appropriate lasers and optics components, the 10897D supplies unsurpassed positioning accuracy for dynamic measurement.
-
Product
EZ-Glider Position Control Torque Arms
-
Equipped with position encoders, the position control torque arm is an error-proofing system that detects and eliminates costly screw-fastening errors during the assembly process. The poka-yoke system reduces the risks of improperly fastening screws, ensuring that every screw is correctly tightened in the correct sequence. In critical applications, tightening fasteners in the correct sequence ensures the reliability of the joint. The position control system is like putting the eyes and ears of a quality control manager where they are needed most – right at each work station.
-
Product
Temperature, Humidity And Others Relevant Environment Tester
-
King Design Industrial Co., Ltd.
Allows your product quality and reliability tests more realistic toward actual environment; simulate the actual environment in the temperature, humidity and vibration by separated of combined tests. The tester is equipped with control panel, Chinese-English display and micro-computer temperature control system; applicable to aerospace, military, vehicles, electronics and other high-tech products.
-
Product
Optical CMM Systems
-
Our OmniLux metrology system is highly versatile and provides unparalleled levels of 3D CMM capture for component measurement in seconds. This high precision non contact, metrology system is extremely versatile because it measures components of any geometry and of any material. Geometries possible include: spheres, asphere, cylinder, internal bore, cone/taper, step height or freeform in any material such as polished or rough metals or ceramics and polymers. The Omnilux is fast and accurate because, unlike direct contact sensors, the use of optical sensors means that the whole surface can be analysed while the object is suspended in space, ensuring that no damage comes to delicate surfaces. Our easy-to-use software interface, developed from years of experience enables the operator to effortlessly control the system. Rich data analysis, automation and export of results for the immediate generation of reports as well as a compact footprint means OmniLux is the leading solution for production or R&D environments where reducing cycle times is critical to sustainable success.
-
Product
Transmission Control
-
Schweitzer Engineering Laboratories, Inc.
Transmission control systems provide flexible local control and SCADA integration for substation and line protection assets, improving your system’s reliability and efficiency.
-
Product
AM Control System
Clamir
-
*Continuous monitoring of melt pool dynamics and geometry.*Ensures quality and repeatability.*Compatible with most laser heads.*Compatible with a wide range of materials.*Easy mechanical integration.*Quick configuration.*Helps to reduce CO2 emissions.
-
Product
PCI Resistor Card 2-Channel 2 Ohm To 65.5k Ohm With SPDT
50-293-133
Programmable Resistor Module
The 50-293 is a Programmable Resistor card with either two channels of 16-bit or four channels of 8-bit resistor chains in a single PCI card. The card is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
PMAC Controller CPU's
-
PMAC Controllers are a family of high-performance motion control systems used in a wide range of applications, including machine tooling, semiconductor manufacturing, robotics, and scientific research.
-
Product
PCI Resistor Card 4-Channel 1 Ohm To 127 Ohm
50-293-012
Programmable Resistor Module
The 50-293 is a Programmable Resistor card with either two channels of 16-bit or four channels of 8-bit resistor chains in a single PCI card. The card is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Wide Range High Voltage Programmable DC Power Supply
N3600 Series
-
Next Generation Instrumental (Shanghai) T&C Tech. Co., Ltd.
N3600 series is developed based on NGI's years of experience in testing for battery fluctuation simulation test, battery charger, high voltage diode, electrolytic capacitor, electromechanical control, ATE test system, etc. It is a high-voltage wide-range programmable DC power supply. According to different test environments in the fields of lab test, system integration test, and mass production line, NGI has made a number of optimization designs based on the international advanced technology. N3600 series is a market leader in similar products in terms of reliability, maintainability and safety.
-
Product
Rotational Speed Sensors
-
Rotation speed sensors are used to monitor, regulate and control mechanical drive systems and play a major role when it comes to protecting elements of a rotational system (e.g., in the engine, drive) from mechanical overload. Micro-Epsilon offers two sensor systems for rotation speed measurement. The capaNCDT CST6110 is a universal rotation speed sensor for counting tasks and rotation speed applications of any type. Moreover, the turboSPEED DZ140 measuring system is specifically designed for the detection of turbocharger rotation speeds.
-
Product
PXI Resistor Module 4-Channel 1R to 127R
40-293-012
Programmable Resistor Module
The 40-293 is a Programmable Resistor module with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
GPIB-ENET/1000 , Ethernet GPIB Instrument Control Device - United States 120VAC
781630-01
GPIB Controller
The GPIB‑ENET/1000 is an IEEE 488 controller device for computers with an Ethernet port. You can use this device to share a single GPIB system among many networked users or to control several test systems from a single networked host. The GPIB‑ENET/1000 features a password-protected web interface for easy configuration. It can also control IEEE 488 devices from anywhere on an Ethernet‑based (LAN) TCP/IP network (Gigabit, 100BASE‑TX, 10BASE‑T). Each device interfaces to and shares up to 14 GPIB devices from several network hosts, and you can control up to 100 GPIB‑ENET/1000 interfaces with a single computer. The device includes a license for the NI‑488.2 driver software, providing maximum reliability for connecting to third-party instruments with GPIB.
-
Product
Millimeter Wave Control Devices
-
Ducommun millimeter wave products include various control devices for system integration. The CAE, CPS, CPD and CPM series control devices are discrete or MMIC based PIN diode attenuators and switches. The CAF, CAL, CAR and CPL series control devices are waveguide based mechanical tunable attenuators and phase shifters. These devices are offered to cover the frequency range from 18 GHz to 110 GHz.
-
Product
PCI High Density Potentiometer Card 9-Channel, 8-Bit, 0 To 255 Ohm
50-296A-121-9/8
Programmable Potentiometer
The 50-296A series are Programmable Potentiometer versions of the 50-295A Programmable Resistor cards with up to 9-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Flexible Current Sensor Probe
CTA
-
The CTA current sensors convert ac current to an isolated 0-5A current with available ranges from 100A to 10,000A. Because the current sensors are flexible split core, installation is possible without shutting down the LV electrical supply, avoiding expensive down-time costs. Typical applications are retrospective energy monitoring in factories, offices buildings, process control data logging systems, where power, energy and current monitoring is important. Typical applications are factories, offices buildings, ac/dc VFD drives, welding, power conversion and power distribution. For all CTA current sensor models, a NIST/NPL (UKAS) traceable calibration certificate and certificate of conformance is supplied. All CTA sensors use UL94V0 or CSA approved materials. The CTA flexible current sensors are suited to permanent or semi permanent installation. The coil sensor is durable, lightweight, flexible and will easily clip-around a power cable. The 5A output from the CTA current sensor connects direct to installed metering, rotary metering or current transducers.
