Video Distribution Amplifiers
See Also: Distribution Amplifiers
-
product
Composite 1×24 Video Distribution Amplifier
VDA124RM
Video Distribution Amplifiers (sometimes called a video splitter – not to be confused with a video split screen controller such as our PXD510E split screen controller) are typically used for connecting a camera or other video source to several monitors that do not have “looping” inputs. In this situation, each monitor has a permanent 75 ohm termination. With two non-looping monitors connected together, the line would be double loaded and result in a dim picture on each monitor. Using a Video Distribution Amplifier will solve this problem by driving each monitor individually at 100%.
-
product
RGB 1×3 Video Distribution Amplifier
VDA403
Video Distribution Amplifiers (sometimes called a video splitter – not to be confused with a video split screen controller such as our PXD510E split screen controller) are typically used for connecting a camera or other video source to several monitors that do not have “looping” inputs. In this situation, each monitor has a permanent 75 ohm termination. With two non-looping monitors connected together, the line would be double loaded and result in a dim picture on each monitor. Using a Video Distribution Amplifier will solve this problem by driving each monitor individually at 100%.The second application is when the video signal is run over distances greater than 50 feet. The coaxial cable has a fair amount of signal loss over long distances. When multiple monitors are connected after long runs of coax, the degradation can be severe, especially when dealing with modern, high bandwidth signals that have 500+ lines of resolution.The VDA403 is a Video Distribution Amplifier designed for professional applications. It will operate with NTSC & PAL video signals as well as many common Black & White signals. These units use the latest integrated amplifier technology for superior performance and reliability. Custom units or modifications can be manufactured at a reasonable cost.
-
product
Composite 1×24 Video Distribution Amplifier Board
BL-VDA124-01
Video Distribution Amplifiers (sometimes called a video splitter – not to be confused with a video split screen controller such as our PXD510E split screen controller) are typically used for connecting a camera or other video source to several monitors that do not have “looping” inputs. In this situation, each monitor has a permanent 75 ohm termination. With two non-looping monitors connected together, the line would be double loaded and result in a dim picture on each monitor. Using a Video Distribution Amplifier will solve this problem by driving each monitor individually at 100%.
-
product
Composite 1×24 Video Distribution Amplifier
VDA124RM-12
Video Distribution Amplifiers (sometimes called a video splitter – not to be confused with a video split screen controller such as our PXD510E split screen controller) are typically used for connecting a camera or other video source to several monitors that do not have “looping” inputs. In this situation, each monitor has a permanent 75 ohm termination. With two non-looping monitors connected together, the line would be double loaded and result in a dim picture on each monitor. Using a Video Distribution Amplifier will solve this problem by driving each monitor individually at 100%.
-
product
Composite 2×12 Video Distribution Amplifier
VDA212RM
Video Distribution Amplifiers (sometimes called a video splitter – not to be confused with a video split screen controller such as our PXD510E split screen controller) are typically used for connecting a camera or other video source to several monitors that do not have “looping” inputs. In this situation, each monitor has a permanent 75 ohm termination. With two non-looping monitors connected together, the line would be double loaded and result in a dim picture on each monitor. Using a Video Distribution Amplifier will solve this problem by driving each monitor individually at 100%.
-
product
Composite 2×12 Video Distribution Amplifier 12VDC
VDA212RM-12
Video Distribution Amplifiers (sometimes called a video splitter – not to be confused with a video split screen controller such as our PXD510E split screen controller) are typically used for connecting a camera or other video source to several monitors that do not have “looping” inputs. In this situation, each monitor has a permanent 75 ohm termination. With two non-looping monitors connected together, the line would be double loaded and result in a dim picture on each monitor. Using a Video Distribution Amplifier will solve this problem by driving each monitor individually at 100%.
-
product
Composite 1×6 Video Distribution Amplifier
VDA106
Video Distribution Amplifiers (sometimes called a video splitter – not to be confused with a video split screen controller such as our PXD510E split screen controller) are typically used for connecting a camera or other video source to several monitors that do not have “looping” inputs. In this situation, each monitor has a permanent 75 ohm termination. With two non-looping monitors connected together, the line would be double loaded and result in a dim picture on each monitor. Using a Video Distribution Amplifier will solve this problem by driving each monitor individually at 100%.
-
product
PXI Voltage Amplifier SMB Type Connector
41-650-002
A 5 channel voltage amplifier ideal for increasing the output voltage from other PXI modules, enabling users to easily generate the signal voltages commonly required in applications such as automotive test.
-
product
Signal Amplifier
9200A
Model 9200A was designed as a general purpose, wide band and high voltage amplifier however, with specific applications in mind. It is built in a small case size to save space and cost but without compromising bandwidth and signal integrity.
-
product
AI-Enabled Video Analytics Platform
Railway efficiency is not bounded by gauge or speed. Rather, AI deployed on railway computing infrastructure, especially at the network edge, has tremendous potential to improve operations and bottom lines. ADLINK's line of EN 50155 compliant AI-enabled platforms offer rail solution providers a high level of flexibility to select the configuration best suited to their use cases, and help them accelerate their railway digital transformation with edge AI.
-
product
PXIe Dual Channel 20GHz 30dBm RF Amplifier
3202
Model TE3202 is a dual channel RF amplifier in a single slot PXIe form factor that can operate from 100kHz to 20GHz, designed for high frequency, and high power signal amplification.
-
product
Signal Amplifier
9100
Model 9100 is a Single/Dual Channel, 2U, half-rack size, bench-top power amplifier designed for signal amplification. With unprecedented signal purity, Model 9100 amplifies signals from DC to over 500kHz. The unit has a fixed gain of x15 however the same amplifier is available with custom gain and no signal purity or performance degradation whatsoever.
-
product
Distribution Board, For 8 N181x SPDT Switches
Y1150A / 34945EXT
Connects the 34945EXT to 8 N181x SPDT to route the power and control signals from the driver module to the switches
-
product
Synchro Power Amplifiers
SSP
Computer Conversions Corporation
The SSP Series are Compact, Reference Powered and Isolated Synchro Power Amplifiers, and AC Sine/Cosine ( Resolver ) to synchro converters; designed for moderate wattage, and re-transmission requirements; providing ultra high efficiency, and ultra high reliability in service, and ease of use. They are ideally suited for demanding Naval/Maritime, Aircraft, and Radar/Antenna related, applications. They are commonly used on synchro based data transmission, retransmission, simulation, and active control systems. They are suitable to drive both CT and CDX type passive loads, and virtually any synchro input instrumentation, or control.
-
product
Broadband Amplifier
BBA130
The R&SBBA130 broadband amplifiers offer a variety of setting options so you can optimally tune the output signal to your specific application. During operation, you can adjust the operating class for transistors between Class A and Class AB as well as choose between maximum output power or higher mismatch tolerance at the output.
-
product
Signal Amplifier
9200
Model 9200 is a Single/Dual Channel, 2U, half-rack size, bench-top power amplifier designed for signal amplification. With unprecedented signal purity, Model 9200 amplifies signals from DC to over 500kHz. The unit has a fixed gain of x15 however the same amplifier is available with custom gain and no signal purity or performance degradation whatsoever.
-
product
USB Preamplifier, 10 MHz to 4 GHz
U7227A
The U7227A, 10 MHz to 4 GHz USB preamplifier is designed to bring reliable gain and low noise figure to measurement systems improving the overall system performance and reduce systematic errors; a total solution to the X-Series signal analyzers to perform noise figure measurements.
-
product
InfiniiMax II Series Probe Amplifier, 10 GHz
1168B
Provides a large common mode range and a large offset range for measuring differential and single-ended signals.
-
product
Synchro & Resolver Buffer Amplifiers
RPMA - SPMA
Computer Conversions Corporation
The SPMA/RPMA Series are low cost solid state synchro and resolver buffer amplifiers, isolators and format converters packaged in industry standard 2.6 x 3.1" modules for printed circuit card mount.
-
product
Amplifier for the Frequency Range from 2 Hz to 50,000 Hz.s
Trig-Tek™ 203M
Versatile amplifier covers the frequency range from 2 Hz to 50,000 Hz.s and provides has three simultaneous outputs
-
product
Charge Amplifier for Outputs from Piezoelectric- or mV-type Accelerometers, Force Gauges, Microphones & Pressure Pickups
Trig-Tek™ 201AP
Amplify the outputs from piezoelectric- or mV-type accelerometers, force gauges, microphones, and pressure pickups
-
product
Microwave System Amplifier, 2 GHz To 8 GHz
87415A
The Keysight 87415A microwave component amplifier brings compact, reliable gain block performance to systems integrators and microwave designers. With 25 dB minimum gain and over 23 dBm output power from 2 to 8 GHz, this amplifier offers output power where it is needed: at the test port.
-
product
PXI Voltage Amplifier, +/-33V
41-650-001-S1
A 5 channel voltage amplifier ideal for increasing the output voltage from other PXI modules, enabling users to easily generate the signal voltages commonly required in applications such as automotive test.
-
product
InfiniiMax III+ Series Probe Amplifier, 4 GHz
N2830A
The N2830A Series InfiniiMax III+ probing system is the next generation of InfiniiMax probing, greatly expanding the measurement capability and usability of a probe capable of measuring all components of a differential signal. The built-in InfiniiMode technology allows customers to switch differential, single-ended, and common mode without adjusting probe tip connections.
-
product
34945EXT Distribution Board, For One 87204x/206x Or 87606B Switch And Two N181x Switches
Y1152A
The Y1150A-Y1155A distribution boards enable simple connections to the external switches. The distribution boards plug onto the 34945EXT and are used to route the power and control signals from the driver module to the switches using standard cables.
-
product
Preamplifier, 10 MHz to 4 GHz
87405B
Preamplifiers and System Noise Figure Application Note This note discusses noise figure basics including applications and characteristics of Keysight simplifier technology. Highlighted are Keysight's 87405C portable preamplifiers that provide an exceptional gain of 25 dB up to 18 GHz and a probe-power bias connection which eliminates the need for an additional DC power supply. Read the Preamplifiers and System Noise Figure Application Note now!
-
product
PXI Voltage Amplifier D Type Connector
41-650-001
A 5 channel voltage amplifier ideal for increasing the output voltage from other PXI modules, enabling users to easily generate the signal voltages commonly required in applications such as automotive test.
-
product
19" Rackmount Rugged, Fanless AIoT Platform for Real-time Video/Graphics Analytics
AVA-5600
- Intel® Core™ i7-7820EQ Processor and Mobile Intel® CM236 Chipset- NVIDIA Quadro® GPU MXM 3.1 Type A/B module on PCIe x164x M12 GbE with PoE, 4x USB 3.0- Rich Storage Options: 2.5" SATA 6.0 Gb/s drive bay, 1x M.2 2280 slot, 1x CFast socket- GNSS/3G/4G/WLAN support via 2x Mini PCIe slots and 2x USIM slots- MVB/CAN bus support by Mini PCIe add-on module (BOM option)- Nominal Voltage: 110VDC (EN50155 compliant)
-
product
2-26.5 GHz Traveling Wave Amplifier
1GG7-8045
The 1GG7-8045 is a broadband GaAs MMIC Traveling Wave Amplifier designed for high output power and moderate gain over the full 2 to 26.5 GHz frequency range. Seven MESFET cascode stages provide a flat gain response, making the 1GG7-8045 an ideal wideband power block. Ebeam lithography is used to produce gate lengths of ~0.3 mm. The 1GG7-8045 incorporates advanced MBE technology, TiPtAu gate metallization, silicon nitride passivation, and polyimide for scratch protection.
-
product
1×6 Video Distribution Amplifier
VDA206 S-Video
Video Distribution Amplifiers (sometimes called a video splitter – not to be confused with a video split screen controller such as our PXD510E split screen controller) are typically used for connecting a camera or other video source to several monitors that do not have “looping” inputs. In this situation, each monitor has a permanent 75 ohm termination. With two non-looping monitors connected together, the line would be double loaded and result in a dim picture on each monitor. Using a Video Distribution Amplifier will solve this problem by driving each monitor individually at 100%.
