Hall Sensors
-
product
Turbidity Sensors
Turbidity sensors measure the amount of light that is scattered by the suspended solids in water. As the amount of total suspended solids (TSS) in water increases, the water's turbidity level (and cloudiness or haziness) increases. Turbidity sensors are used in river and stream gaging, wastewater and effluent measurements, control instrumentation for settling ponds, sediment transport research, and laboratory measurements.
-
product
Hyundai Oxygen Sensor
KS60113 - Hyundai
Konstar Electric Industrial Co., Ltd
An oxygen sensor, also known as a lambda sensor, continually detects the oxygen content in the exhaust gases of an engine. The oxygen sensor output signal informs the vehicle's ECU (Electronic Control Unit) whether the AFR (Air-Fuel Ratio) is lean or rich. Based on this, the ECU adjusts the amount of fuel injected into the engine to achieve an optimal AFR.
-
product
Sensor Tester
QST-5
The QST-5 device is intended for testing many popular sensors used in the automotive industry. The tester powers the tested sensors by itself, so it can be used both in a vehicle and outside of it.
-
product
LVDT Displacement Sensors "Economy Series"
INELTA Sensorsysteme GmbH & Co. KG
With a higher Rel. linearity error and a smaller Operation temperature range as well as a simplified type of construction, these LVDTs can be poduced and sold cheaper.
-
product
Paddle Wheel Flow Sensor
FSP
FSP - Paddle Wheel Flow Sensor, Using SUS and corrosion-resistant materials and design oxidation resistance, good stability and high resolution built-magnet rotor, NPN pulse square wave can be connected directly to the PLC / IPC IPC, the product is easy to maintain, easy to operate.
-
product
Metal Magmeter Flow Sensor
2552
The Signet 2552 Metal Magmeter features all-stainless steel construction. The PVDF nosepiece and FPM O-rings are the only other wetted materials. The 2552 installs quickly into standard ISO 7-R 1 or ISO 7-R 1 (1 in. to 1 in. NPT) pipe outlets, and is adjustable to fit pipes from DN50 to DN2550 (2 to 102 in.). Two sensor lengths allow maximum flexibility to accommodate a variety of hardware configurations, including ball valves for hot-tap installations.
-
product
Nutrient | Oxygen | PH Sensors: PH Sensors
pH (potential Hydrogen) is a measurement of the level of acids and bases in water. Our pH sensors have been used extensively to research ocean acidification, coral reefs, coastal marine biology, and to conduct environmental monitoring.
-
product
Reference Temperature Sensors
AMETEK Sensors, Test & Calibration
Our reference sensors can be used as your daily working-reference sensors in laboratory or field calibration applications. A large selection of types are available, including; straight, 90 degree angle, 4 mm or 1/4”. The superior design and specifications combined with a long history of reliability and low drift have made the STS probes the working-standard in many EN/IEC 17025 accredited laboratories worldwide. The DLC sensors are a part of our patented Dynamic Load Compensation system.
-
product
Color Sensor
The color sensor product family includes both RGB (Red, Green, Blue) and high-accuracy XYZ light sensors for precise color measurement, determination, and discrimination. XYZ sensors are capable of providing xy chromaticity co-ordinates in accordance with the CIE 1931 color map. The ams color sensors include filters to block unwanted IR light in the visible spectral range, enabling highly accurate color measurement. Their high sensitivity coupled with their wide dynamic range make them well suited to continuous color temperature measurement of ambient light in display management systems, and automatic-white-balance assistance in camera applications. Some products have additional IR channels to assist with IR light source identification.
-
product
Through Hole Type AC Current Sensor
CTF-200B
MULTI MEASURING INSTRUMENTS Co., Ltd.
*For AC current and power measurements.*Suitable for current measurements of main cable.*Measuring range:AC 1A～200A.
-
product
Acoustic Emission Sensors
Acoustic wave (acoustic emission) sensors are the ceramic piezoelectric transducers converting the mechanical elastic acoustic waves generated in the material (e.g. elastic waves occur when a material cracks, wears, deforms, or corrodes) to electrical signals. The electrical signals are then amplified and filtered by a preamplifier and then transmitted to a special acoustic emission acquisition instrument for further data processing and analysis.
-
product
Air Temperature Sensor
HD9008.03
Direct Pt100 1/3 DIN temperature sensor for measuring the air temperature.
-
product
Fluxgate 150A Current Sensor
LF03
Our LF03 current sensor works with the dynamic Fluxgate measurement technology. It is characterized by its simple, practical design and prevents high temperature drifts. Fluxgate technology uses the phenomenon of magnetic saturation to modulate the measured magnetic field and convert it into an electric field.
-
product
Differential Pressure Sensor for Gases
The differential pressure sensors from Sensirion measure reliably, fast and long-term stable. The fully calibrated and temperature compensated sensors offer highest accuracy and resolution, especially at very low differential pressures. The small and cost-effective design makes them an ideal match for price-sensitive solutions, e.g. in medical and HVAC applications.
-
product
SparkFun Soil Moisture Sensor (with Screw Terminals)
The SparkFun Soil Moisture Sensor is a simple breakout for measuring the moisture in soil and similar materials. The soil moisture sensor is pretty straightforward to use. The two large, exposed pads function as probes for the sensor, together acting as a variable resistor. The more water that is in the soil means the better the conductivity between the pads will be, resulting in a lower resistance and a higher SIG out. This version of the Soil Moisture Sensor includes a 3-pin screw pin terminal pre-soldered to the board for easy wiring and setup.
-
product
Optical Sensors
Optical (Infra-Red) Proximity Switches with advanced and reliable technology for every application offer a flexible solution for automation, where other Proximity Switches can not perform. Optical Proximity Switches have distinct advantage of higher sensing distance over Inductive and Capacitive types.
-
product
Hall Effect Measurement system
HMS-3000
Hall Effect Measurement System is very useful for measuring Carrier Concentration, Mobility, Resistivity and Hall Coefficient that should be pre-checked in order to grasp the electrical specifications of semiconductor device. Therefore, it is essentially required system to understand the electrical characteristics of semiconductor device.Ecopia’s HMS series consist of constant current source , terminal conversion system by Van der Pauw technique, low temperature(77K) test system and magnetic flux density input system. So, it is well-established system that has all the things needed to Hall Effect Measurement System.
-
product
Variable Reluctance Pressure Sensor with All-Welded Construction
DP10
The DP10 Pressure Sensor, is designed for low and medium pressure measurements, to laboratory accuracy, of corrosive liquids and gases. In typical AC excited bridge circuits, this transducer delivers a full scale output of 30 mV per volt at 3kHz. The unit operates with carrier system including the Validyne CD15 since wave carrier demodulator and CD16 miniature DC input DC output carrier demodulator.
-
product
Oxygen Measurement Analyzers, Transmitters & Sensors
Precise oxygen measurement is critical for processes in many industries, ranging from the purity of industrial gases and protecting against leaks in glove boxes to monitoring flue gas for optimum combustion efficiency.
-
product
T-Type Thermocouple, 32°F to 500°F Temperature Sensor
745685-T02
T-Type Thermocouple, 32°F to 500°F Temperature Sensor - The T-Type Thermocouple works with NI measurement devices and software to help you acquire temperature data within a measurement system. You can use LabVIEW or FlexLogger software and NI-DAQmx driver software to configure … measurements and predefined scaling coefficients for the T-Type Thermocouple and acquire synchronized temperature data in units of degrees. The T-Type Thermocouple is available in various lengths and configurations including field-cuttable, ready-made sensors, and thermocouple wire extensions with a -20°F to 221°F temperature range.
-
product
Conductivity-Resistivity Sensor Electronics and Integral System with PVDF Sensor
2850
The Signet 2850 Conductivity/Resistivity Sensor Electronics are available in various configurations for maximum installation flexibility. The universal mount version is for pipe, wall, or tank mounting and enables single or dual (digital versions only) inputs using any standard Signet Conductivity/Resistivity sensor. The threaded j-box version can be used with these same Signet sensors for submersible sensor mounting. It is also available as a combined integral system configuration for in-line mounting and includes a conductivity electrode in a choice of 0.01, 0.1, 1.0, 10.0 or 20.0 cm-1 cell constants. The 2850 is ideal for applications with a conductivity range of 0.055 to 400,000 S or a resistivity range of 18.2 M to 10 k.
-
product
RFID-Coded and Magnetically Coded Safety Sensors
- Actuation possible from different directions- Meets the interface description CB24I from ZVEI- Can be connected in series- Conceal behind stainless steel for enhanced tamper prevention- Meets highest safety levels to ISO 13849-1 and SILCL 3 to IEC 62061
-
product
High-power, Retro-reflective Laser Sensor
LV-H67
High-power, Retro-reflective. Ultra-high power laser with a maximum detecting distance of 50m(164?). The bright beam spot allows easy optical axis alignment, even at a long distance.
-
product
AC/DC Split Core Current Sensor CT1000S
This AC/DC split core current sensor is designed for measuring large DC and AC currents in applications such as electric vehicles, renewable energy systems, inverters, and motors. It facilitates high-current measurements by clamping around existing current connections. With its voltage output, this sensor is compatible with power analyzers (WT series and PX8000) and waveform measurement instruments (ScopeCorders and DLM series), making it a versatile tool for various high-current measurements.
-
product
TMR Switch Sensor Demo Board
MultiDimension Technology Co.,Ltd.
Demonstration kit for MDT omnipolar and bipolar TMR switch sensors
-
product
SparkFun RGB Light Sensor
ISL29125
If you’ve had ideas for a project that depends on the ability to sense different spectrums of visible light and react based on those measurements, the ISL29125 breakout board may be just what you need. The ISL29125 breakout board makes it very easy to sense and record the light intensity of the general red, green, and blue spectrums of visible light while rejecting IR from light sources. You can then use these color sensor readings for the purposes of logging and finding patterns, or creatively calculate and make control decisions in your electronic projects.
-
product
Position Sensors for Hazardous Environments
Intrinsically Safe systems provide a safe operating environment for personnel and equipment. Intrinsic Safety (IS) is based on the principle of restricting the electrical energy transmitted into a hazardous area, thereby ensuring that anysparks or heated surfaces that may occur as a result of electrical failures areinsufficient to cause ignition. The threat of an explosion is eliminated.
-
product
Tyre Pressure and Infra-Red Sensors
The system consists of a powered pressure and temperature sensor with transmitter fitted to a wheel rim. This sends pressure and temperature data over an RF link to a compact receiver on the car. Sampling rates increase automatically when either a change in pressure is detected or when wheel inertia is detected. The system stops transmitting below a threshold pressure to preserve battery life. The receiver sends data to the car control via CAN.
-
product
Stud Sensors
Stud Sensors such as the MSV100 and MSV350D comprise a category of their own. Each uses electromagnetic induction to sense the presence of (and thereby locate) a stud, pipe, batten, current-carrying wire or other metallic object behind a wall or above a ceiling. The two instruments differ in their choice of the display technology (LED or LCD) used to pinpoint position.
-
product
Fixed Infrared Temperature Sensors
This fixed infrared sensors selection is vast with many different features without any lack in quality. These infrared sensors are designed for fixed continuous non-contact temperature measurement.
