Timers
mark time.
See Also: Time, Time Interval, GPS Time, Time Reference, Time Code, Time Domain, Time Standards, Timing, Time Interval Meters, Counter / Timers
-
product
PXI Switch - 16-CH General-Purpose SPDT Relay Module
PXI-7901
ADLINK PXI-7901 is a general-purpose (GP) switch module implementing 16-CH independent single-pole double-throw (SPDT) relays (1 Form C). PXI-7901 can connect one input to one output and be used as signal switching and routing for measurement system or ATE. Thanks to its high switching capacity, PXI-7901 can also be used to turn on or turn off devices such as motors, fans, heaters, and lights. The contact position of the relays can be changed either by direct software commands or by following the instructions previously stored in the on-board scan list. The scan list advances upon the trigger from external measurement devices, such as a DMM. The scan list could also advance when the scan-delay timer expires. In the PXI-7901, PXI trigger functions are supported and software programmable. Multiple modules can therefore be synchronized without additional field wiring.
-
product
Watchdog Timer and System Monitor Card
PCIe-WDG-CSMA
This multifunction Low Profile x1 PCI Express card contains a watchdog timer used to monitor the operation of your application program and operating system to initiate a system reset in case of a lockup. It can also monitor and control a variety of system hardware parameters. The card is 6.6 inches long and 2.535 inches seated height. I/O wiring connections are via a female DB25 connector on the card mounting bracket. Two models with increasing features are available.
-
product
LED Displays
LED display timer that can be used to time various situations and events such as talent, speakers, presentations, experiments, etc. The LED display has a brightness control and the 0.8" characters are large enough to be read across a room.
-
product
PCI Express Card with 96 DIO and Counter/Timers
PCIe-DIO-96C3
This is a x1 lane PCIe, 96 line digital input/output card with counter/timer capabilities designed for use in high I/O density application requirements. I/O connections are made via four 50-pin header connectors. The card is 12.25 inches long (312 mm) and may be installed in any full-length slot that has x1 lane PCIe.
-
product
Circuit Break Timer Test Set
PME-500-TR
Before developing the system or equipment for the testing of a circuit break timer for distribution, the application information was obtained by consulting various users of this type of timer for circuit breaker. The customers consulted were from private service and maintenance companies, large industries, and of course from the Utility companies. It is essential to receive first hand information of the actual requirements and needs of each of these customers who are making these types of tests and then make a detailed study of the various alternatives offered by different manufactures of this type of circuit breaker timer.
-
product
3.5” Embedded SBC With Intel® Pentium® Processor N4200 & Celeron® Processor N3350, LVDS, HDMI, 2 GbE LANs And Audio
CAPA313
The CAPA313 is powered by the Intel® Pentium® processor N4200 or Intel® Celeron® processor N3350 (codename: Apollo Lake). This 3.5" embedded board was designed for operational stability in harsh environments with a wide operating temperature range from -20°C to +70°C. It offers a wide range DC input of 12V to 24 for various industrial environments. It also comes with rich I/O connectors, stunning graphical performance and an emphasis on expandability. In addition to one 204-pin DDR3L-1867 SO-DIMM socket supporting system memory up to 8GB, the CAPA313 has one PCI Expess Mini Card slot for 3G/4G, GPS, Wi-Fi and Bluetooth connection. The compact-size embedded board comes with one RS-232/422/485, one RS-232, two USB 2.0, four USB 3.0, eight-channel digital I/O, audio, LVDS, HDMI, VGA (optional) and dual Gigabit LANs with Intel® i211AT Ethernet controller. It also features one SATA-600 socket and one mSATA interface for storage devices. To ensure reliable operation, the 3.5” embedded SBC supports watchdog timer and hardware monitoring features.
-
product
PCI Multifunction I/O
626
6 versatile 24-bit counters for encoders/timers with interrupt generation Fail-safe Digital I/O E-stop Relay Battery backup of counters Four 14-bit D/A outputs, 20 Khz update rate Sixteen 16-bit differential A/D inputs, 15 kHz rate Watchdog timer may be used to reset PCI bus 48 bi-directional digital signals for solid state relay boards, 40 with edge detection and interrupts
-
product
Insulation Tester
1kV Megohmmeter
*Calculations (automatic)*Potential Index and Dielectric Absorption Ratios*Tests Continuity, Resistance and Frequency Measurements*Programmable Alarms*Insulation Test, Resistance, Continuity*Hazardous Voltage Alert (Icon) if voltage is >70 volts 5.) On Board Timer, +1/- 1 sec
-
product
General Purpose Radiation Survey Meter/Geiger Counter
Rad 100™
The RAD 100™ is a general purpose radiation survey meter/geiger counter that detects and measures alpha, beta, gamma, and X-radiation. It is intended for personal safety and educational purposes. Like the popular Radalert® 100X, the RAD 100™ features a 3-second update on its digital liquid crystal display (LCD). The LCD shows the current radiation level in your choice of microSieverts per hour (SI units) or mR/hr for gamma radiation measurements. For mixed sources (alpha, beta, gamma) the CPM mode is recommended. This instrument also offers an accumulated total and timer function, up to 9,999,000 counts and 40 hours. A red LED blinks and a beeper chirps with each count (the chirp can be muted). This is a professional instrument that is also easy to learn to use and to operate, and carries the industry leading Medcom warranty (2 years overall limited to 1 year on the GM sensor). Many instruments designed by the Medcom team are still working perfectly after 30 years of use, so this instrument should provide a lifetime of useful information.
-
product
Almanac Time Switch
IM1754
Almanac Tme Switch is a real time timer which can be used to switch electrical appliances like street lamps, garden lights, corridor lights, neon signs etc. as per time of the day. The timer has built in Almanac timings fixed in Nonvolatile RAM so that the user does not have to programme the unit from time to time. This Almanac time switch has added advantage over daily dial or weekly timers. Timer provides two outputs to drive contactors of different ratings. These outputs can be used with different combinations to achieve desired output. Timer is provided with manual override facility. Optional detachable external keyboard unit provided to avoid unauthorized access.
-
product
DC - 400 MHz PC-Based Timer Interval Analyzer
GuideTech’s GT658PCI is an ultra-fast, high resolution, DC – 400 MHz Time Interval Analyzer (TIA), ideal for most PC-based lab bench (timing) test applications. What makes the GT 658 superior to traditional counters is analogous to the difference between volt meters & digital scopes. While both measure voltage, the scope provides much more information about the dynamics of the signal. This is because our patented TIA substantially increases measurement speed, and the measurements are displayed as afunction of time. All of these features, along with the benefit of ‘continuous time correlation to a common reference between all measurement time stamps,’ enable our TIAs to make measurements that weren’t previously possible with traditional counters.
-
product
Data Logging
The LogTxt macro can be used together with a timer macro in a loop to produce a data log that consists of a timed series of data samples. Each line in the file can be anything you want, typically a time-stamp (including date, if desired) plus one or more values recorded at that time. The interval between samples can typically be from less than a tenth of a second, up to hours or days... or even longer.
-
product
Venturi Flow Measurement Trainer (UITM-22)
Unitech Scales And Measurements Pvt. Ltd
UNITECHS venturi flow measurement trainer comprises of an Venturi meter fitted between the piping. A small FHP pump is used to circulate the water through the piping. Pressure ports brought out from the Venturi meter are connected to a U tube mercury manometer to measure the pressure difference. Collecting tank of capacity 5 liter is provided with graduations to measure water level. Digital timer is fixed to calculate the flow rate. Flow can be controlled using a manual control valve. The complete setup is mounted on a table top model.
-
product
Save A Watt HD
P4472
Take control of your electronics and appliances. Simply connect them to the Save A Watt® HD timer, and they will turn on and off based on your preferred settings. Electronics which are plugged into an outlet are drawing power even when not in use, slowly draining your wallet! Having the power to program ON/OFF times saves you money, and prolongs the life of your electronics. With a large, backlit, digital face, setting the time couldn’t be easier or more intuitive. If you forget which settings you chose, it only takes a glance to find out.
-
product
Timers
Omega has timers with large, bright digital readouts. We have them in benchtop models, wall mountable units, and hand-held form factors.
-
product
Digital Circuit Breaker Analyzer
CT-3500 S2
The CT-3500 S2 is Vanguard’s second generation, stand-alone, digital, microprocessor-controlled, circuit-breaker timer. It measures the elapsed time from the instant a breaker coil is energized to the instant of opening or closing of a circuit-breaker’s dry contacts. In addition to timing a breaker’s contact response time, the CT-3500 S2 can also time relays or other switching functions that use an initiating trigger voltage (24-300 Volts DC or AC). The timer-triggering voltage starts three independent electronic timers. Each timer is individually stopped by its respective dry-contact closing or opening. The CT-3500 can fully analyze the timing of all circuit breaker operations (Open, Close, Open – Close, and Close – Open). Timing results are displayed in milli-seconds and cycles on the unit’s back-lit LCD screen and can be printed on the built-in 2.5-inch wide thermal printer.
-
product
Automated AC Digital Hipot Tester
Educated Design & Development, Inc.
1 button testing - No setup required, just plug right in! Or, make a plug for your cordless product, and plug right in! EASY!Easy to identify PASS / FAIL visible and audible indicationAuto Test Time (1 sec. / 60 sec.)+ - No need to set a timer or clock watchSafety Protected Start Switch -- Protects user from shock!Performs the Low Current Ground Continuity test at the same timeMeets UL, CSA, CE, EN, IEC, MIL and all other international safety agency requirements as well as UL 120Kohm requirementsIncludes ISO/IEC 17025 Accredited Calibration Certificate, accredited by ACLASS (Internationally accepted results... equivalent to A2LA)
-
product
Handheld Circuit Breaker And Timer Analyser
CAT-H Series
The operation of the breaker can be initiated in different ways (e.g. from a control room, by a local breaker or externally by a test device) depending on the test conditions. Various time measurement triggers are available to record a measurement under a different test condition:*Coil control channel*Continuous current clamping channel*DC voltage channel
-
product
Current Digital Set Point Relay
These Digital set point relay for current (type mrd2011-a) are field proven with excellent sensitivity and are with two independent outputs and are used as under current and over current controlling operations. The two independent outputs are programmable in a specific range i. E. The range if it is 25a the settings can be made within the range of 250 a. This facility of having the liberty to set the required current is added advantage in the digital meters of these models available in the market. The set points are field settable within the range mentioned in the model. these relays have inbuilt timers and this facility enables the user to avoid external timers and external wiring. The timers are programmable from 0 second to 20 seconds. The ranges available are up to 2500 a. The dimensions are compact and are of 96 mm x 96 mm x 65 mm only. The auxiliary supply for the relay is 110v ac or 230v ac.
-
product
Digital I/O Board, 32 Isolated I/O Channels, 24V, LACQUERED
APCI-1500-LAC
PCI interface to the 32-bit data busConnector compatible to PA 1500Connector and software compatible to CPCI-150016 isolated input channels, 24 V, including 14 interruptible3 software-programmable counters/ timers16 isolated output channels, 10 to 36 V, output current 500 mATimer-programmable watchdog for the reset of the outputs to ??Diagnostic report through status register in case of short-circuit, overtemperature, voltage drop or watchdogInterrupt triggered through watchdog, timer, errorOne ground line for all inputs and one ground line for all outputs
-
product
Switch Analyser
SA10A
It has a built-in micro Ohm meter/Ductor for measuring of static and dynamic resistance of the breaker poles. It only weighs 11,6 kg. The versatility and precision that this unit offers is, without question unchallenged, and it will indeed be your best partner when testing circuit breakers. Tests in areas with high induction at known problematic substations has proven the SA10A to be the only circuit breaker timer that could withstand these extreme conditions. It's rugged, it's small and highly appreciated by our customers.
-
product
Static Decay Timer
PDT-740B
Designed to measure the time required for a 1,000 volt charge to dissipate to less than 100, 50 or 10 volts in tenths of a second.Used to evaluate the static decay capabilities of materials, personnel, equipment and other products.Compatible with most portable CPM's and field meters having an analog output of ± 2 (10,000 volts equals 1 volt).Used in conjunction with the PFM-711A Field Meter.Can be used with the PGB-745 Decay Electrodes or PRF-911 Concentric Ring
-
product
96/48-CH Opto-22 Compatible PCI Express Digital I/O Cards
PCIe-7248/7296
ADLINK"s PCIe-7248/7296 are high-density parallel digital I/O boards with 96/48 I/O channels. The header connectors are fully compatible with industry Opto-22 standard. Thus, PCIe-7248/7296 can utilize the Opto-22 external devices. The PCIe-7248/7296 devices emulate mode 0 of the industry standard 8255 programmable peripheral interface (PPI) chips. The PCIe-7248/7296 provides 4/2 PPI chips respectively. Each PPI offers three 8-bit ports: Port A, Port B and Port C. The Port C is divided into 2 nibble-wide (4-bit) ports. The PCIe-7248/7296 devices have programmable timer/counters. One 16-bit counter is available for event counting, while the other 32-bit timer is available for timed interrupt generation. The PCIe-7248/7296 devices provide multiple programmable interrupt sources from DIO channels, as well as the output of the timer.
-
product
Timer Relays
A Timer Relay is a combination of an electromechanical output relay and a control circuit. The contacts will open or close before or after a pre-selected, timed interval.
-
product
Up/ Down Counters
LED display timer that can be used to time various situations and events such as talent, speakers, presentations, experiments, etc. The LED display has a brightness control and the 0.8" characters are large enough to be read across a room.
-
product
Preheating Test Setup for Hair Straightener
SCR ELEKTRONIKS have developed "60 Stations Preheating Test Setup for Hair Straightener“ for Testing of Hair Straightener. It consists of Adjustable Constant Voltage source, Digital Timer, Digital Voltmeter, Digital Timer for carrying out Heating Test of Hair Straightener. It has got the capacity to check hair straightener that require test current 28 A at different Test Voltages.
-
product
Fanless Desktop Network Appliance Platform With Intel® Celeron® Processor N3350 1.10 GHz And 3 GbE LANs
NA345E
The fanless NA345E adopts the low-power consumption Intel® Celeron® processor N3350 (codename: Apollo Lake). It aims to provide small business and SOHO customers an energy-saving and cost-effective network appliance for solutions in VPN, content filtering, UTM, network security gateway, and firewall. The desktop NA345E supports one non-ECC DDR3L-1866 SO-DIMM socket providing system memory of up to 8GB; moreover, it offers one mSATA for storage. It is equipped with three 10/100/1000 Mbps LAN ports (Intel® i211 Ethernet controller). The network appliance platform also has two USB 3.0 ports and an RJ-type serial console port. The system features a watchdog timer for reliable operation. Additionally, it supports Linux operating system.
-
product
Insulation Tester
Calibrated 1kV Megohmmeter
*Calculations (automatic)*Potential Index and Dielectric Absorption Ratios*Tests Continuity, Resistance and Frequency Measurements*Programmable Alarms*Insulation Test, Resistance, Continuity*Hazardous Voltage Alert (Icon) if voltage is >70 volts 5.) On Board Timer, +1/- 1 sec.
-
product
Automatic Relay Tester
DYR-II
Model ‘DYR-II’ is an ideal, newly developed multifunction relay tester adopting monolithic computer technology. It is composed of auto synchronized digital millisecond timer, logic controlling unit, multifunction digital display, high precision digit collection and processing unit, current-voltage output unit, overload and over range protection unit. Test process is automatic for improved efficiency. The tester has a built in printer for printing the results.
-
product
x1 PCI Express System Timer
SKU-048-01
The x1 PCI Express System Timer uses a hardware clock to synchronize IP signals. This hardware-based solution provides accurate clock timing for Asterisk® open-source PBX software.The Timer supports variable clock timing intervals. You can configure the clock interval during startup. Currently, the x1 PCI Express System Timer supports clock intervals ranging from 1ms to 64ms.
