Silicon
atomic number 14 tetravalent metalloid chemical element.
-
Product
Pulse Characterization Sensors
-
Pulse Characterization Sensors provide the ability to see and measure the temporal characteristics of pulsed and CW laser beams. Ophir Fast Photodiode Detectors are designed to convert optical signals into electrical signals which are then measured with third-party instrumentation such as oscilloscopes and spectrum analyzers. Accessories are available to connect to IS6 integrating spheres or fiber optic cables. Attenuating filter accessories are also available to increase their dynamic range. Different models offer silicon, UV enhanced silicon and InGaAs PIN photodiodes, covering a combined spectral range of 193 nm to 1700 nm. Rise times range from 25 picoseconds to 3 nanoseconds. The fast rise times are achieved by an internal reverse bias voltage circuit. Power is supplied by internal batteries and/or an external power supply depending on the model. Detectors should be connected to a 50Ω impedance in order to maintain their nominal rise times. They can be connected to higher impedance loads, but this will result in a significant increase in the rise time. If higher output voltage is required, it is recommended to connect the detector to a trans-impedance amplifier with an Input impedance of 50Ω
-
Product
Test Leads
AL-34WB 10A
-
Standard Electric Works Co., Ltd
● Wire length: 1m approx. Silicone insulated wire (700mm) with wire connected to straight input plugs (150mm PVC wire), and wire for clamp (150mm PVC wire).● Outside diameter of silicone insulated wire: 6.4mm Outside diameter of PVC wire: 4mm● Input plug color: Red•Green•Black•Blue ● Current rating: 10A● Voltage rating: 300V● Designed for Milliohm meter, Micro-ohm meter, Low resistance measurement with high current injection. ● Conductor size: 40mm maximum● Safety standard: IEC/EN 61010-031 CAT IV 300V
-
Product
Radar Core Chips
-
Macom Technology Solutions Holdings Inc.
Multifunction GaAs and Silicon MCM designed for communication radar and weather applications. MACOM Core Chips deliver a complete transmit/receive function with phase and amplitude control.
-
Product
Laboratory Centrifuges
-
Centrifuge systems are designed for the development, test, evaluation and calibration of accelerometers and a variety of inertial devices. Centrifuges provide a cost-effective solution for simulating high-"G" environments in the laboratory. They support testing of devices such as MEMS-based Inertial Measurement Units (IMUs), low-cost quartz or silicon sensors, Ring Laser Gyros (RLGs), Fiber-Optic Gyros (FOGs), fuzes and crash sensors.
-
Product
Wideband True RMS AC Voltmeter
323
-
The Ballantine 323 True RMS analog ac voltmeter uses advanced true rms circuitry to achieve square law response from rugged, fast responding silicon diode detectors with no thermal lag and overload vulnerability inherent in thermocouple devices.
-
Product
Light-to-Analog Sensors (Current)
-
Renesas' light-to-current silicon optical sensors combine a photodiode array and current amplifiers on a single monolithic IC. These devices are ideal for display and keypad dimming, as well as industrial and medical light sensing applications.
-
Product
Environmental Test Chamber
-
The chamber is produced by SUS304 Steel, the temperature keeping material is produced by Polyurethane hard foam and ultra-fine fibre glass, the doorframe heat insulated by Double high temperature aging silicone rubber door sealing strip.The temperature controller is used by Korean TEMI display in English/Chinese and German Siemens PLC, it can be communicated to PC via RS-232. The temperature accuracy is 0.1 and humidity is 0.1%R.HThe temperature sensor is platinum PT100 Ohms/MV resistor
-
Product
XYZ Color Sensor
AS7261
-
Calibrated XYZ color sensor provides complete, integrated platform for handheld color analyzers, color calibration and mobile analysis devices. Tri-stimulus XYZ realized by silicon interference filters. UART or I²C slave digital Interface. 16-bit ADC with digital access. Programmable LED drivers. 20-pin LGA package 4.5mm x 4.7mm x 2.5mm, with built-in aperture. Compact true-color sensing. Applications; Color/CCT sensing, Fluid or reagent analysis, Color point comparison, Display calibration.
-
Product
RZ Family of 64-Bit & 32-Bit Arm-Based High-End MPUs
RZ/G
-
RZ/G Series MPUs extends the capabilities of RZ/A Series to deliver high-end performance for graphics, multi-stream video, and embedded vision thanks to features like camera input, 3D graphics accelerators, Full HD video codec, and GbE. Renesas also offers the RZ/G Linux platform, which is a user-friendly software development environment for customers who wish to lower the barriers and cost of Linux adoption and maintenance. The RZ/G Linux Platform enables super-long-term Civil Infrastructure (CIP) Linux support in an industrial grade verified Linux package, which complements Renesas’ high quality silicon.
-
Product
Solar Cell PL/EL/IV 3-in-1 Testing System
VS6841
-
Industrial Vision Technology Pte Ltd.
This luminescence Analyzer integrates a Photoluminescence (PL), Electroluminescence (EL) , and I-V Measurement Technology, has a Device’s PL image, EL image, as well Device’s I-V characteristics in One system. It is being using to quantitatively map Minority-Carrier Lifetime, and to characterize the defect of silicon wafer & solar wafer, and measure the key parameters from solar cell I-V Curve. It is also a useful tool for scientist to develop other methodology & parameters that can be used as a promising technique for online material monitoring and process control.
-
Product
Photodiodes
-
Opto Diode manufactures high quality standard and custom photodiodes. Our wide range of standard device feature low dark current and low capacitance. The silicon detectors are ideal for general purpose applications, laser monitoring, position sensing, measuring photons, electrons, or X-rays, or for detecting sun and rain applications. The devices operate from the deep UV to the near-infrared wavelengths.
-
Product
Silicon Nails Feature Development And Runtime, GTE 10.00p
K8228A
-
The Silicon Nails test development tool also allows users to define the vectors that they would like to execute on the non-compliant boundary scan device. The test development tool will generate the boundary scan test to output or input at the relevant interconnecting pin, thus generating the test consistently.
-
Product
Digital Solutions
Digital ST120 Dual Thermopile (Preliminary)
-
A two channel silicon- based thermopile in a TO-5 package that includes integrated electronics which incorporate an industry standard digital SMBus interface. Each small active area size is 1.2mm x 1.2mm.
-
Product
Scienlab Battery Test System – Pack Level, 110 KW Compact Version
SL1710A
Test System
Keysight’s SL1700A Scienlab Battery Test System – Pack Level Series allows to realistically emulate the environment of the future battery pack application in order to test the high-power battery pack comprehensively and improve its functions and safety. The growing demand of e-mobility increases the need of vast battery test labs for EV battery development. Keysight developed the SL1700A Series to accelerate the development and validation of batteries. It offers a voltage range of up to 1500 V and power options between 100 and 300 kW including a Performance Bundle to increase the power up to 330 kW. The new high-voltage SiC (silicon carbide) technology provides a high energy efficiency on a small footprint and helps to minimize your operating costs.
-
Product
Computer-On-Module
CM22301
-
LinkedHope Intelligent Technologies Co.,Ltd.
CM22301 uses Intel® sixth-generation Skylake platform and Core M low-power SoC processors, and integrates the full functions of CPU, GPU and South/North Bridge on a single chip. The processor provides powerful computing and display performance with dual-core and four threads configuration. Its turbo frequency can boost up to 3.1GHz and the display output resolution can be up to 4K. CM22301 has an amazing thermal design power consumption of only 4.5W (TDP) and can be used for a variety of high-performance fanless designs. CM22301 supports up to 16GB dual-channel low-voltage DDR3L memory populated onboard, and up to 64GB on-board solid state disk silicon, as benefit the development of ruggedized products for harsh environment applications.As defined by VITA 59 specification, CM22301 provides up to 6 PCIe lanes, enabling flexible functionality expansions, such as NICs, DAQs, video capture and so on. Meanwhile, CM22301 also provides up to date computer interfaces like GbE, SATA3, USB3.0/2.0, HD Audio, etc. CM22301 uses the same 220pin board-to-board connector and Type10 pin out definition as COM Express.
-
Product
Switches-Limiter
-
Macom Technology Solutions Holdings Inc.
At MACOM we offer an extensive collection of switches covering multiple commercial and aerospace and defense markets. Our product portfolio has a broad frequency spectrum from DC to 70 GHz. Our silicon Heterolithic Microwave Integrated Circuit (HMIC) PIN diode process is ideal for high power and broadband switches operating from 50 MHz to 26 GHz. Our AlGaAs PIN diode process can extend the upper frequency range of our switch die beyond 70 GHz and is ideal for instrumentation and radar applications. Our GaAs pHEMT and MESFET technology is ideal for fast switching and low control voltage switches optimized for both narrow band and broadband applications. Our 75 Ohm absorptive switches are designed specifically for demanding CATV, FTTx and DBS Infrastructure and CPE applications.
-
Product
Microcontrollers (MCUs)
8-bit
-
An innovative 8-bit chip design provides a fully-integrated experience. Silicon Labs' 8-bit MCUs are ideal for IoT applications and beyond, delivering the industry's fastest speeds and lowest power.
-
Product
In-Line Wafer Surface Defect Inspection
ALTO-SD-150/200
-
ALTO-SD SERIES IS AN IN-LINE INSPECTION SYSTEM SUPPLYING HIGH THROUGHPUT, FULL SURFACE DEFECT INSPECTION FOR ALL KINDS OF WAFERS INCLUDING SILICON, QUARTZ, SAPPHIRE, COMPOUND AND MEMS WAFERS. HIGH-RESOLUTION CAMERA OPTICS PLUS LED ILLUMINATION GUARANTEE RELIABLE DETECTION OF ALL LOCAL DEFECTS. IT INSPECTS DEFECT SIZE OF 1~ 10 MICRONS, CONFIGURABLE INSPECTION RESOLUTION TO OPTIMIZE DEFECT SIZE VS. THROUGHPUT. THE SYSTEM COMBINES HIGH-PRECISION MEASUREMENT, POWERFUL DATA ANALYSIS AND USER-FRIENDLY OPERATIONS.
-
Product
SparkFun Triple Axis Accelerometer And Gyro Breakout
MPU-6050
-
The MPU-6050 is a serious little piece of motion processing tech! By combining a MEMS 3-axis gyroscope and a 3-axis accelerometer on the same silicon die together with an onboard Digital Motion Processor™ (DMP™) capable of processing complex 9-axis MotionFusion algorithms, the MPU-6050 does away with the cross-axis alignment problems that can creep up on discrete parts.
-
Product
Clean Room Torque Screwdrivers
-
High-value products manufactured to clean room standards need quality tools. Located in Silicon Valley, Mountz makes clean room screwdrivers that exceed Class 100 (ISO 5) clean room standards. Our built-in cam-over mechanism ensures industry-leading accuracy in even the most sensitive of environments. Mountz clean room screwdrivers offer companies the security of knowing the products they've invested in turn out exactly as designed.
-
Product
Wide Measurement Range Model Of Semi-automatic 4 Point Probe Sheet Resistance/resistivity Measurement
RT-3000/RG-2000 (RG-3000)
-
*User programable measurement pattern & programmable measuring pattern*Tester self-test function, wide measuring range*Thickness, edge, temperature correction for silicon wafer*Film thickness conversion function from sheet resistance*2 types measuring tester (S version: Standard type, H version: High range resistivity measurement type)
-
Product
X-Band Silicon Radar Quad Core IC
AWS-0105
-
The AWS-0105 is a highly integrated silicon quad core IC intended for radar and 5G phased array applications. The device supports four radiating elements, single beam transmit, and single beam receive and includes all requisite beam steering controls for 6 bit phase and gain control. The device provides 21 dB gain and +15 dBm output power during transmit mode and 7 dB gain and +7 dBm IIP3 during receive mode. Additional features include gain compensation over temperature, temperature reporting, and fast beam switching using eight on-chip beam weight storage registers. The device features ESD protection on all pins, operates from a +1.8 V supply, and is packaged in a 56 lead 7x7 mm QFN for easy installation in planar phased array antennas.
-
Product
High Performance Fluorescent X-ray (XRF) Coating Thickness Gauge
FT150 Series
-
Hitachi High-Technologies Corp.
The FT150 is a high-end fluorescent X-ray coating thickness gauge equipped with the polycapillary X-ray focusing optics and Vortex silicon drift detector. The improved X-ray detection efficiency enables high throughput and high precision measurement. Furthermore, new design to secure wide space around sample position gives exellent operability.
-
Product
Schottky Barrier Bridge Quads
-
SemiGen’s Silicon Schottky Diodes are designed for applications through 40Ghz. The special process technology utilizes various metal schemes to provide excellent performance of Low, Medium, and High Barrier applications. The end result is a low resistance diode with tightly controlled capacitance which allows for optimum performance. Low conversation loss and superior TSS make these diodes ideal for detector / mixer applications with frequency ranges from S band to Ka band as well as modulators, lower power limiters and high speed switches.
-
Product
BGA Sockets
-
Ironwood has the most comprehensive collection of BGA (Ball Grid Array) sockets that can be used for prototype application, silicon validation, system development, thermal characterization, burn-in application, functional production test, etc. BGA socket can be defined as an electromechanical device, which provides removable interface between IC package and system circuit board with minimal effect on signal integrity. BGA sockets for prototype applications, silicon validations, system development applications uses low cost elastomer contact technology.
-
Product
Scienlab Battery Test System – Pack Level, 330 KW
SL1740A
Test System
Keysight’s SL1700A Scienlab Battery Test System – Pack Level Series allows to realistically emulate the environment of the future battery pack application in order to test the high-power battery pack comprehensively and improve its functions and safety. The growing demand of e-mobility increases the need of vast battery test labs for EV battery development. Keysight developed the SL1700A Series to accelerate the development and validation of batteries. It offers a voltage range of up to 1500 V and power options between 100 and 300 kW including a Performance Bundle to increase the power up to 330 kW. The new high-voltage SiC (silicon carbide) technology provides a high energy efficiency on a small footprint and helps to minimize your operating costs.
-
Product
Resistivity Standard
-
Resistivity Standards are bare silicon wafers available in 3 in, 8 in and 12 in sizes. The silicon is p-type (Boron) doped to nominal resistivity values, from 0.002 ohm.cm to 75 ohm.cm as available on the 3" model.
-
Product
Spectroelectrochemical Flow Cell
SEC-2F
-
Using the spectroelectrochemical flow cell, it is possible to have a different optical path length changing the gasket. We offer, as an optional item, a silicon and Teflon gasket with a 100, 250 and 500 m of the thickness. SEC-2F Spectroelectrochemical flow cell was designed to fit perfectly in the SEC2000 Spectrometer, and it eliminated the use of the optical fiber to connect the Spectrometer to the SEC-2F. Even for another brand of the spectrometer, you can connect the SEC-2F using the collimating lens and optical fiber.
-
Product
Open Top BGA Sockets
-
Ironwood has the most comprehensive collection of open top BGA and QFN sockets that can be used for qualification application, silicon FIB testing, system development, thermal characterization, burn-in application, etc. IC socket can be defined as an electromechanical device, which provides removable interface between IC package and system circuit board with minimal effect on signal integrity. Typical packages include BGA, LGA, QFN, QFP, WLCSP, etc. Open top allows access to the top side of IC. Below is an example BGA socket that uses low cost elastomer contact technology.
-
Product
Ceramic Process Carrier Pallets
-
Ceramic engineering specializing in Silicon Carbide, Boron Carbide, Alumina, Zirconia and Lead Zirconate Titanate (PZT) based ceramics, composites and thin films for High Strength, high temperature, semiconductive ceramic designed for use in wafer fabrication or hybrid circuits in vapor deposite ovens. Test Electronics will precision drill and customize pallets for your circuit board. Click on the Quote tab on the left then click on the Carrier Pallets tab to get an instant quotation on your process carrier pallets.
