Power train
translates energy generated into work.
-
product
AC Power Source
6500 series
The global AC power testing requirements demand more sophisticated AC Power Source that is capable of simulating a wide variety of AC line conditions, harmonic waveforms, accurate power measurement and analysis. The Chroma 6500 series Programmable AC Power Source delivers the right solution to simulate all kinds of normal/abnormal input conditions and measure the critical characteristics of the product under test. It can be used for R&D design characterization, production testing, and QA verification of commercial, industrial, and aerospace electronic products. The Chroma 6500 series delivers maximum rated power for any output voltage up to 300 Vac, and at any frequency between 15Hz to 2000Hz. It is suitable for commercial applications (47-63Hz); for avionics,marine, military applications at 400Hz or higher frequency; or for electrical motor, air-conditioner test applications at 20Hz. All models generate very clean sine or square waveforms output with typical distortion less than 0.5%. The Chroma 6500 series has built-in Direct Digital Synthesis (DDS) Waveform Generator to provide user programmable high precision waveform. For testing products under AC line distortion conditions, clipped sinewave can be generated with 0% to 43% distortion and amplitude from 0% to 100%. It also can simulate all kinds of power line disturbances such as cycle dropout, transient spike, brown out, phase angle, voltage and frequency ramp up (ramp down), etc.. Up to 30 harmonic waveforms are factory installed, and testing for compliance to AC line harmonic immunity standards can be easily achieved in the field.
-
product
3-Phase AC Power Source
61700 series
The Chroma Programmable AC Power Source model 61700 series delivers pure, 5-wire, 3-phase AC power. Unlike the traditional 3-phase AC power source, it includes low power rating models at very low cost. Users can program voltage and frequency, measure the critical characteristics of the output on its LCD display. It delivers the right solution to simulate all kinds of input condition of UUT to be utilized in R&D and QA. It is also suitable for commercial applications from laboratory testing to mass productions. The 61700 supplies the output voltage from 0 to 300VAC and it can be set individually for each phase. Users also can set the phase angle from 0? to 360?. These kinds of function make the 61700 series can simulate unbalance 3-phase power. Because of the wide output frequency from 15 to 1200Hz, it is suitable for avionics, marine and military application. The AC+DC mode extends the output function to simulate abnormal situation when power line contains DC offset.
-
product
AC to DC Programmable Power Sources
CEHCO can supply AC to DC Programmable Power Sources. We offer standard or customized solutions. The ADG-L Series is up to 1000 VDC maximum output. ADG-P Series is up to 2000 VDC maximum output.
-
-
product
High-Power DC Power Supplies
N8900 Series
The Keysight N8900 Series provides 5 kW, 10 kW, and 15 kW auto ranging, single-output programmable DC power for ATE applications that require just the right amount of performance at just the right price. The N8900 Series power supplies' auto ranging output characteristic enables unprecedented flexibility by offering a wide range of voltage and current combinations at full power. Power supplies with "rectangular," or traditional, output characteristics provide full power at only one voltage and current combination. Just one N8900 does the job of multiple power supplies. It's like having many power supplies in one!
-
product
Custom Power On Option
U8002A-AUT
This option helps users to eliminate manual intervention on instrument control when they use U8000 series power supplies in a test system. The behavior of this option and standard units are the same after power up, where the "Output ON/OFF" button is still accessible throughout the supply operations.
-
product
High Power DC Electronic Load
34000A Series（5KW~40KW）
34000A Series has its own control and display panel, CC / CR / CV / CP / Dynamic modes, 150 sets Store / Recall memory which provides load set-up more efficiently, also can be remote controlled via GPIB、RS232、USB and LAN interface.SHORT time setting and SHORT_VH, SHORT_VL setting function, also can measure Short Voltage and Current.
-
product
DC Power Source for Standard Lamp
DC502
DC502 is CONSTANT CURRENT DC POWER SUPPLY for standard lamp. Function and technical indexes are as follows: • output voltage 4 grades: 6V/12V/24V/50V • output current: DC 0~2.5A (adjustable) • Output current drift at full scale: ±0.05% reading value/10 mins • Monitor range of ampere meter: 0.0000A ~1.9500A, 1.950 A ~2.500A • Accuracy of ampere meter: ± (0.08% reading value + 0.02% full scale) • Max output power: 80W • Continuous working time: 8 hours • Work environment: Temperature 0℃ -25℃, humidity ≤ 85%R.H, supply source: AC220 ±10%, 50/60HZ • Holding conditions: -20~50℃ humidity < 75%R.H • Outside dimension (W×H×D): 333mm×114mm×307mm • Weight: about 8kg • Power: about 1000VA
-
product
Digital Power Recorder
MPR-601W-02
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Applicable for single phase 2wires and single phase 3wires and 3phase 3wires system*Wide measuring range up to 0～500V/500A*Easy data logging by USB flash memory
-
product
*Laser Power & Energy Meters
Ophir laser power meters work on the smart plug principle. This means that almost any Ophir power meter can work – plug and play – with almost any of the wide range of Ophir sensors. Ophir power meters are also the most precisely calibrated units on the market thus measuring with the highest accuracy. Noted for their versatility, ease of use, and user friendly interface, Ophir meters can be used stand-alone or interfaced with LabVIEW or the user's own software.
-
product
Automotive Audio Power Amplifiers
ST is the recognized leader in automotive power amplifiers. Our car audio amplifiers provide the traditional clean and powerful sound that users have come to expect, as well as all the protection and safety features needed to make our devices robust in an automotive environment.
-
product
AC-DC Power Supplies
Our AC-DC power supply solutions can be designed to meet almost every conceivable application requirement in terms of power, performance, efficiency, communications, protection, size, approvals compliance, and cooling requirements.
-
product
Linear DC Power Supply
MPS-H-1 Series
MPS-H-1 series DC power supply is a new generation of high-quality linear DC power supply, with remote voltage compensation function, automatic conversion of voltage stabilization and current, high stability, high reliability, high precision, and display output voltage and current at the same time. Very high cost-effective advantage.
-
product
Power System Recorder
TESLA LITE
ERLPhase Power Technologies Ltd
The new TESLA LITE is an economical user-friendly multi-timeframe power system recorder: Economical yet complete power system recording for custom applications in smaller substations. Easy to use intuitive software Simultaneous transient fault, dynamic swing and trend recording and event logging Fault location derived from single and calculated currents IRIG-B clock synchronization (modulated and unmodulated) Smallest footprint among recorders allows easy retrofit and installation 12 current, 6 voltage and 38 digital inputs
-
product
Power Distribution Boards
Power distribution systems can be offered in addition to solutions for power supplies. This includes power distribution boards, which take over the power distribution in your system. When developing the system solution, in addition to the technical requirements such as high energy efficiency, simple further processing is decisive. The competence for high-performance circuit boards, enclosure constructions as well as assembly and system tests, which has been developed over the years, enables us to offer you the best possible power supply and distribution.
-
product
Power and Energy Automated Calibration System
RS-933
The RS-933 Syntron Power and Energy Automated Calibration System calibrates a range of test equipment including; Energy Reference Standards, Digital Multimeters, Phase meters, Energy meters, Power meters, Revenue meters, Amp meters, Panel meters & Power Quality meters.
-
product
Micro Power Contacts
Micro Power
Rated to 10,000 cycles.Rated to 21 Amps cont w/ 12 AWG wire.Max contact resistance of 1.5 mOhms.Mating force of 2 lbs.
-
product
Power Amplifiers
In this product category you find highly linear power amplifiers for digital and analog data transmission, power amplifiers for CW applications and for laboratory use, which stand out due to its liability, robustness and long-term availability and which are based on the semiconductor technologies which are actually available on the market.
-
product
ATE System Power Supplies
N5700 Series
The Keysight N5700 Series delivers low noise power in a compact 1U package. Airflow moves front to back, so no additional space is required above or below the power supply in your automated test equipment (ATE) rack. Select output voltages from 6 to 600 V. For low current applications, the 750 W models provide 1.3 to 100 A. For higher current needs the 1500 W models provide twice as much current.
-
product
Panel-mounted Power Amplifier
PAC2000B
PA series amplifiers are specially designed for power network real time simulation applications,which requires large power output,high accuracy even at high current output for all kinds of load.
-
product
Power Quality Analyzer
Weshine Electric Manufacturing Co., Ltd
Three Phase Power Quality Analyzer High Precision
-
-
product
High Powered External IP Transmitter
PowerSting
The PowerSting is a series of external high power transmitters (5kW, 10kW, and 15kW) for the SuperSting R8/IP/SP and SuperSting R1/IP/SP. The PowerSting system is a fully programmable constant voltage//constant current source. The PowerSting system comes with an SGS generator and a wireless repeater box, and operates in both wired and wireless modes. The applications of the PowerSting-SuperSting system include vertical electrical sounding, 2D electrical imaging, 3D electrical imaging, 3D offset electrical imaging of a 2D survey line in both manual and automatic modes.
-
product
Customaizable Uninterrupted Power System
CT Series
The rugged CT Series is designed for applications in extreme temperature environments, such as offshore drilling rigs, refineries and shipboard use. An added benefit is that the CT Series can double as an electronic power conditioner/frequency converter as well. All CT systems utilize Power Factor Correction, and RS232 and SNMP protocols are supported.
-
product
Programmable Benchtop DC Power Supply
62000L
Chroma Systems Solutions, Inc.
Provides high quality yet cost effective programmable benchtop DC power, designed to meet the stringent requirements of the next generation of power electronics.
-
product
AC/DC Power Supply 60 W
TR100M180
AC/DC power supply with 100 W from Cincon | input ranges 90 - 264 VAC | output 18 V | operates in temperature from -20 to +80 °C | provides 2 MOPP
-
product
Digital Power Meter, 30A
Chroma 66205
Chroma Systems Solutions, Inc.
66205 is the 2nd generation of the 66200 series power meter designed specifically for single channel measurement. Its state-of-the-art design is capable of providing highly accurate power measurements to meet the requirements of IEC 62301/EN50564 standards. Functionality improvements of the 66205 increase power measurement capabilities to a wider range of applications.
-
product
Virtual Optical Power and Energy Meter
844-PE-USB
The Model 844-PE-USB is a Power Meter with a USB connection to use a computer as the monitor, allowing the user to access the full computing power of the computer.
-
product
AC to AC Programmable Power Sources
AFV-P Series
Rating:600 VA to 5 KVASingle Phase OutputOutput frequency: 45 Hz to 500 Hz (Optional for 15 Hz to 1000 Hz)
-
product
Power Dividers/Combiners
Macom Technology Solutions Holdings Inc.
MACOM’s power combiners and dividers are used in aerospace and defense, wireless, and wireline communications applications. These devices can also be used for broadband CATV applications. They are available in a variety of connectorized and surface mount packages. Available in subsets operating between the 400 kHz to 26 GHz frequency range, our dividers and combiners are characterized as both 50 and 75 ohm devices
