Filter Results By:
Products
Applications
Manufacturers
Bipolar Power
smooths transition between negative and postive precision DC voltage at any amount.
See Also: DC Power Supplies
-
product
Bipolar Power Transistors
A wide variety of products are rolled out, for example, for uses at high temperature (up to 175°C applicable), high power, and low Vce (sat), and others.
-
product
Bipolar Power Supply, 0 to ±50 VDC, 100 AMPS, 10 KW, P/N 19215PS
Specifications:Bipolar Power Supply, 10 KW, P/N 19215PSInput: 220 / 230 / 240 VAC, 46 Amps, 1 PH, 50 HzOutput 1: 0 to ± 50 VDC, 100 Amps max, Upper SectionOutput 2: 0 to ± 50 VDC, 100 Amps max, Lower SectionEnclosure: 42″H x 32″W x 22″DAll connections are inside the enclosureThis unit is a dual output power supply
-
product
Test System
ITC57300
The ITC57300 Dynamic Parametric Test System mainframe accepts Test Heads that perform nondestructive transient measurements on semiconductor devices such as Insulated Gate Bipolar Transistors (IGBT), power MOSFETs, diodes, and other bipolar devices(requires additional optional bias power supplies and custom personality boards). Included in the mainframe are all test equipment and software necessary to analyze and perform resistive and inductive switching time, switching losses, gate charge, Trr/Qrr, and other transient tests.
-
product
BJT Modeling
IC-CAP supports a number of bipolar junction transistor (BJT) models. For more information on the various types of IC-CAP supported BJT models, refer to the table below.
-
product
Single Channel High Voltage Linear Amplifier
F20A
The F20A is a general purpose broadband linear amplifier having a fixed amplification of 20 times and capable of bipolar high voltage output of ±150V. Any functiongenerator or arbitrary waveform generatoror any othe signal source with amplitude up to ±10 V can be used as an input device. The amplifier's output is linear from DC up to megahertz range. It can be used in a wide range of applications, for example to drive piezo actuators, MEMS, OLEDs, liquid crystals, etc.
-
product
Wafer Sort
TestEdge offers complete wafer sort solutions. Our range of wafer sort capabilities demonstrates our ability to handle a wide range of devices and device characteristics. State of the art Electroglas probers Sort experience with high probe count Less than 4 mil pitch on probes Experience with C4 Bump and Aluminum pad Experience on Bipolar, CMOS, GaAs, & SiGe Overhead sort or cable harness sort Microsite testing capability
-
product
8-CH 12-Bit Isolated Analog Output Cards
PCI-6308 Series
- Supports a 32-bit 5 V PCI bus- Isolated 8-CH 12-bit voltage output- 2500 VRMS optical isolation- Jumper selectable bipolar and unipolar output ranges- 4-CH isolated DI and 4-CH isolated DO- Current output version available on PCI-6308A
-
product
Transformer Performance Tester
JYM
JYM insulation resistance tester is used for on-site insulation resistance measurement. The instrument has built-in positive and negative bipolar high-voltage power supplies, with large output power and strong load capacity. It is suitable for insulation resistance measurement of samples with large capacitance, such as power transformers and cables.
-
product
MOSFETs, MESFETs, and Schottky Diodes
Semiconductor Module
The Semiconductor Module allows for detailed analysis of semiconductor device operation at the fundamental physics level. The module is based on the drift-diffusion equations, using isothermal or nonisothermal transport models. It is useful for simulating a range of practical devices including bipolar, metal semiconductor field-effect transistors (MESFETs), metal-oxide-semiconductor field-effect transistors (MOSFETs), Schottky diodes, thyristors, and P-N junctions.
-
product
Higher Range DC Gauss Meter
329 Series
Integrity Design and Reseach Corp.
Portable w/ Dimensions: 5.8"x3.6"x2.5"Range: +/-(20 G, 200 G, 2kG, 20kG)Bandwidth: 68HZ at 3dbComes with 9v DC adaptor & hard carrying caseAnalog Output: +/-200 mV DC FS3 1/2 digit bipolar displayPowered optional either by 9v battery or AC adaptor
-
product
Linear Accelerometer Switch
Columbia Research Laboratories
Columbia Research Labs Accelerometer Switch is designed to interface with electrical or mechanical systems to control, safeguard against, or warn of undesirable variations in DC and low frequency acceleration. This sensor is available with a selectable switch point, a single or Bi-polar switch, and a choice of input power.
-
product
Diode Tester
FEC VF40CM
Frothingham Electronics Corporation
The VF40CM is intended for testing VF, HALF CYCLE SURGE, and THERMAL RESPONSE/RESISTANCE on small- and medium-power diodes and rectifiers. It can also measure THERMAL RESPONSE/RESISTANCE on NPN and PNP bipolar transistors using an external user-supplied VCB supply.The VF40CM also is sometimes used to measure VZ of low-voltage zener diodes up to the compliance voltage limit of the tester. 20V at 20A is possible.
-
product
Single Channel High Voltage Linear Amplifier
F10A
The F10A is a general purpose broadband linear amplifier having a fixed amplification of 10 times and capable of bipolar high voltage output of ±100V. Any functiongenerator or arbitrary waveform generatoror any othe signal source with amplitude up to ±10 V can be used as an input device. The amplifier's output is linear from DC up to megahertz range. It can be used in a wide range of applications, for example to drive piezo actuators, MEMS, OLEDs, liquid crystals, etc.
-
product
6.5 Digit Low Noise Power Source
B2960 Series
The Keysight B2960 Series 6.5-digit low noise power source are a new generation of power sources offering precision, wide bipolar output ranges, and other innovative features such as graphing capability and arbitrary waveform generation capability, enabling test and evaluation that conventional power sources cannot do.
-
product
40-72 GHz Doubler
1GC1-8048
The 1GC1-8048 is a balanced diode frequency doubler consisting of two Schottky diodes and a coplanar balun structure. The doubler provides 15 dB conversion loss and 17.5 dBc 1st and 3rd order feed-thru for input frequencies between 20 and 33.5 GHz. This IC is fabricated in HFTC's InGaP/GaAs heterojunction bipolar transistor (HBT) process that provides excellent uniformity, reliability and 1/f noise performance.
-
product
Mezzanine System
5093
ECM P/N 5093 provides 2 independent full bridge circuits. The two full bridge circuits can be used together to drive one small two phase stepper motor. Each full bridge circuit can drive one small dc motor or other bipolar load. Note all inductive loads should employ transient protection.
-
product
8/16-CH 16-Bit Analog Output Modules
cPCI-6208/6216 Series
- PICMG 2.0 Rev 2.1- 16-bit D/A resolution- 16-CH voltage on 6216V- 8-CH voltage outputs on 6208A and 6208V- 8-CH current outputs on 6208A- Bipolar analog output range- 4-CH TTL DI and 4-CH TTL DO- Rear I/O available
-
product
Pulse Initialization Demo Board
TMR9112
MultiDimension Technology Co.,Ltd.
The TMR9112 demo board was developed to support evalution of the TMR9112 single-axis sensor. The demo board comes with the fast bipolar current pulsing circuit needed for initialising the TMR9112 sensor, and it can be powered from a USB port or any external 5V power supply. For user convenience, the demo board has an optional on-board timer clock with four selectable frequency settings. The On-board timer clock and frequency output can be enabled using the jumper pins. This demo board is divisable along the dotted line so that the sensor board can be seperated from the pulsing circuit board.
-
product
8 Channel Fast Amplifier
V975
The Mod. V975 is an 8 channel fast rise time amplifier housed in a 1-unit VME module; each channel features a fixed voltage gain of 10. Channels are bipolar, non-inverting and can be cascaded in order to obtain larger gain values. Input bandwitdth is 250 MHz for signals up to 50 mVpp and decreases for larger ones (up to 110 MHz @ 400 mVpp). Each channel is provided with three LEMO 00 connectors, one for the input and two bridged for the output.
-
product
Four Channel Low-Noise DC Bias Card
PI-41702
The PI-41702 is a four channel bipolar DC Bias supply that can provide an output current up to 100 mA per channel. The output voltage ranges from –8 V to +8 V, and this card has special filter circuitry to reduce the output noise for those applications that require a low noise bias output. Additionally there is a ‘D’ type connector that allows the introduction of laboratory type supplies to reduce the noise further. To change from using the internal power supplies to external power supplies requires repositioning jumpers. The PI-41702 also has voltage and current sense for remote measurement of the voltage and current levels.
-
product
Parallel Interface Voltage Output D/A Converters
Analog Devices offers a large portfolio of parallel interface voltage output D/A converters (DACs). We provide precision, fast settling, rail-to-rail micropower VOUT D/A converters, with resolutions of 8 bits up to 16 bits, single-channel to 40-channel density, and a unipolar or bipolar supply. These devices are used in a wide variety of applications such as process control, automotive test equipment, or digital gain and offset adjustment.
-
product
Timers
ST offers industry-standard and low-power timers, in single and dual versions. These are highly-stable monolithic circuits, generating accurate time delays or oscillations. The industry-standard frequency generators are circuits designed in bipolar technology, while the the low-power frequency generators are designed in CMOS technology.
-
product
Data Acquisition Device A2D / D2A
General Features10 DAC channels5 ADC channelsDifferential or single ended IOs Full scale bipolar or unipolar signaling
-
product
Voltage Controlled Oscillators
Teledyne Microwave Solutions (TMS) offers Voltage Controlled Oscillators (VCOs) utilizing bipolar transistors & silicon varactors over the frequency range of 40 MHz to 18GHz. Many of the VCO designs incorporate internal filtering, regulation & amplifiers to meet total system requirements in a small integrated package. Additionally, our hermetic hybrid designs can be screened to the most demanding military and space applications.
-
product
Non-Contact Displacement Sensing System
KD-2306
Multi-purpose non-contact position/displacement sensing* Supports both dual and single coil sensors* Terminal I/O connections* Auto-synchronization of multiple channels* Analog DC and 4-20mA outputs* Single ended, bipolar, and differential voltage outputs* Front face coarse and fine calibration controls* RoHS compliant and CE marked
-
product
Amplifier Module
LNAM-B
Fully differential ultra-low-noise voltage amplifier module (LNAM) with selected bipolar rf transistors at the input stage. The amplifier exhibits ultra-low voltage noise, very high speed, and good dc precision. 50 Ohm input termination realized by negative feedback allows for the lowest possible noise temperature.
-
product
Bipolar Transistors
Renesas transistors offer a package lineup including ultra-small packages, suitable for a variety of applications such as large current applications, amplifiers, and support customers' systems.
-
product
Stabilized Power Supplies
Stabilized power supplies are essential devices for providing stable DC voltage to electronic circuits and equipment.They offer features such as precise voltage and current regulation, short-circuit and overload protection, and advanced control functionality.Stabilised power supplies of our own design and manufacture can be built with output power up to 40kW even in models with 2- or 4-quadrant bipolar outputs.
-
product
TMR Switch Sensor Demo Board
MultiDimension Technology Co.,Ltd.
Demonstration kit for MDT omnipolar and bipolar TMR switch sensors
-
product
Ultra Precision Touch Screen Calibrator
DVC-9500
Unprecedented Accuracy of +/-0.0005% error or +/-5ppm- Less than 3ppm/DegC temperature drift- Output simulation of 13 types of thermocouples- +/-2V and +/-20V programmable bipolar ranges- Full Color Touch Screen interface for intuitive interaction
