Electric Vehicle Test Systems
See Also: EV Test Systems, Electric Vehicle
-
product
Electrical Safety Tester
PSE AG has developed an electrical safety test that combines different tests for the testing of PV modules. With our four-in-one tester it is possible to test the following according to IEC 61215-2 and IEC 61730:
-
product
Full-Automatic Testing Machine for Hard Board Vehicles
U800HDIR
. CCD automatic alignment, with an accuracy of ± 10μm2. Support layout test, displacement function3. The upper and lower jigs X, Y, θ are automatically fine-tuned to improve the yield4. Optional laser marking5. Support SHOPFLOOR report output6. Optional BARCODE READER
-
product
Vacuum Leak Test Systems
Vacuum leak testing is the principal leak test method for testing parts that could have leakage from an external source into their housings and casings. Parts like underwater sensors or housings, outdoor electrical housings, sealed components, and components associated with vacuum sources are all prime candidates for vacuum leak testing. Operation of instruments that supply vacuum to test parts instead of pressure works in a similar, yet essentially opposite, manner as pressure decay testing.
-
product
High-Speed Embedded Host Electrical Test Board
HSEHET
High-Speed Embedded Host Electrical Test Board is approved by USB-IF, specifically designed for the electrical test of USB embedded host products.
-
product
Electrical Networks Control System
Electrical networks control system is intended for measurements of network electrical resistance and insulation electrical resistance of the tested specimen. The measurement process takes a couple of minutes.
-
product
Vibrator Test System
Sandwich Box Kit
"Gold standard” for vibrator tests provides more information than radio, wireline similarities or internal analysis. Other forms of vibrator QC use the vibrator controller accelerometers to measure vibrator motion. The Sandwich Box system includes external accelerometers which are used to independently record vibrator motion, thus providing a check of the whole vibrator system including the accelerometers.
-
product
Materials Test Systems
An impedance analyzer is a device that uses a programmable AC voltage / current source, together with voltage and current measurement circuits, to characterize sample impedance over a wide range of frequency. An example of this being the world famous Solartron Analytical 1260A Impedance Analyzer that provides EIS impedance characterization over more than 12 decades of frequency from uHz to tens of MHz. Impedance Analysis characterization is a key technology that enables new materials development for semiconductors, smart-materials, ferroelectrics, piezo-electrics, solid oxide, solid electrolytes, ceramics, polymers, OLED and many more materials.
-
product
Electrical Testing
Our diverse Electrical Laboratory capabilities include measurements from DC to 20 GHz. The equipment assigned to the laboratory is among the most accurate available for the specific measurements of interest. We believe it is the most comprehensive range of testing disciplines of any laboratory in our industry.
-
product
MEMS Testing System
BK3010V2
The BaKo BK3010V2 is our updated MEMS Tester, based on our C-Mic tester, the best selling BK3010. It's small enough to carry under your arm and with a test time of under 0.5 seconds, it tests as fast as you can connect a microphone. Setting up the specifications is very easy and can be done in a few minutes. In addition, the new BK3010V2 can be connected to a computer so you can keep and view compiled data and track trends in variations in your C-Mics.
-
product
Thermal and Mechanical Testing System
3500 System
The Gleeble 3500 is a fully integrated digital closed loop control thermal and mechanical testing system. Easy-to-use Windows based computer software, combined with an array of powerful processors, provides an extremely user-friendly interface to create, run and analyze data.
-
product
Electric Torque Screwdrivers
CL-Series
The CL-Series is electric torque screwdriver that is designed for heavy-duty production and delivers reliability and precision torque. Tool offers proven performance and ensures accuracy in fastening with precision automatic shut-off clutch once preset torque is achieved.
-
product
Opacimeter for the Measurement of Diesel Vehicles
MO / MAHA OPAZIMETER | VP 135043
Maschinenbau Haldenwang GmbH & Co. KG.
The MAHA Opacimeter is used for the measurement of diesel vehicles. The smoke opacity is tested and diagnosed in a time-saving and trouble-free manner in a partial flow procedure during free acceleration or under load of the engine. Rapid readiness for measurement and precise measurement results are the distinguishing features of the MAHA Opacimeter. Type-tested according to PTB requirements 18.09.
-
product
SeaRaptor Autonomous Underwater Vehicle (AUV)
The SEARAPTOR™ is a survey grade deep water autonomous underwater vehicle (AUV) designed to operate at abyssal depths. A wide range of sensors allow the SeaRaptor™ to complete several types of missions including: broad area search with side-scan sonar, hydrographic survey with multibeam and sub bottom profiler, and high resolution inspection survey with camera and acoustic sonar. These surveys support a variety of applications, such as search and recovery, salvage, exploration, construction support, marine archaeology, and oceanography.
-
-
product
Checkpoint Security System
ConneCT
The ConneCTTM Checkpoint Security System is an advanced aviation security explosive detection system (EDS) engineered to deliver superior threat detection, dramatically improved passenger throughput, and low total cost of ownership.
-
product
Electrical Power Transducers
Manufactured for utilities since 1969, TransData Power Transducers are used for measuring AC and DC power variables in Substation, Generation, Load Control and Industrial applications where ±1ma or 4-20mA analog signal are required by the SCADA/Energy Management System. Models are available for measuring Current, AC Voltage, DC Battery Voltage, Watts, VARs, Frequency and more.
-
product
Multi-site Module Testing System
TCIII-3200ST
TurboCATS introduces a new line of redesigned TCIII-3200ST DDR4 and DDR3 multi-site module testing system - compact, high-performance, and equiped with enhanced productivity features. The TurboCATS TCIII-3200ST module test system features an optional 8, 16 or 64 module testing, in parallel, for high throughput on your production floor.
-
product
ATE Test Systems
Introducing the Procyon ATE System! When it comes to ATE Test Systems for a for low- to high-volume production, Intepro has the testing power you require to be successful. For more than three decades, Intepro Systems has designed, built and integrated power supply test equipment for the world’s largest and smallest power supply manufacturers.
-
product
Optics Test Systems
Mobile Wedge Angle Sensor With Positioning System
Optik Elektronik Gerätetechnik GmbH
Mobile wedge angle sensor for determining the wedge angle and the radius of curvature of glass panes, eg windshields of automobiles, helicopters, airplanes or rail vehicles.
-
product
Multi-Purpose RF Test System
SPA441
The S - Series multi-purpose RF test system can be used in many applications such as R&D lab, ATE factory testing, EMC testing, field testing, and general purpose RF design. The S - Series is a flexible alternative to expensive and bulky RF test equipment. As shown in the setup in the upper right the S-Series system can be utilized to simultaneously provide all RF functions using its 7 inch front panel display or can be connected to a larger monitor for ease of viewing multiple windows at the same time
-
product
Electrical Calibration
Multifunction and special calibrators for electrical laboratories. All Meatest calibrators support computer assisted automated calibration to save your time.
-
product
Thruster Test Systems
LS Series
The LS Series Long Stroke Thruster Test Systems are highly regarded as the industry standard for long stroke transient testing. This equipment is used in the design and production test of automotive airbag sensors by leading suppliers of automotive airbags and associative control modules.
-
product
In-System Test Programming System
WriteNow
Based on proprietary WriteNow! Technology, the WriteNow! Series of In-System Programmers is a breakthrough in the programming industry. The programmers support a large number of devices from various manufacturers and have a compact size for easy ATE/fixture integration. They work standalone or connected to a host PC, and are provided with easy-to-use software utilities.
-
product
High Voltage AC Test Systems
Our range of high voltage AC test systems cover from 5kVac to 100kVac. All units have a variable trip range setting and key lock operation to prevent unauthorised use. Applications include testing of insulation systems and measurement of break down voltage of electrical plant and components.
-
product
Full Wafer Contact Test System
Fox 1
Unique cartridge technology uses full-wafer contactors combined with parallel test electronics to achieve single touch, full-wafer test
-
product
Three-phase Fully Automatic Test System
TS41
Calmet Smart Calibration Devices
The Calmet TS41 test system consists of a three-phase reference meter of accuracy class 0.02% (or 0.04%) and an integrated three-phase current and voltage source up to 3x120A/600V. It makes possible automatic testing of electricity meters in meter test stations
-
product
Thermal Imaging System for Electronics Testing
ETS320
Whether the goal is product testing or scientific research, heat can be an important indicator of how a system is functioning. The FLIR ETS320 is a non-contact thermal measurement system that pairs a high-sensitivity infrared camera with an integrated stand, for hands-free measurement of printed circuit boards and other small electronics.
-
product
Electric Testers
ATEQ offers a broad range of electric testers designed to meet the diverse needs of various industries. These testers, including advanced battery testers, are pivotal in ensuring the efficiency and safety of electrical systems. They are used in applications ranging from automotive and e-mobility to broader industrial purposes and EV battery testing. ATEQ’s electric testers are known for their precision, featuring integrated databases for battery types and parameters, secure systems with comprehensive battery protections, and user-friendly interfaces. This makes them essential tools in production lines, research and development laboratories, and for EV/HEV expertise
-
product
NFC Physical Layer Test System
IQnfc+
LitePoint provides turn-key software that facilitates test coil calibration, executes test plan and provides detailed waveform analysis and flexible APIs to customize test flow in the labs.
-
product
Vibration Test Systems
G-5 Series
Both Shock tests at from relatively high acceleration(max. 4900m/s2 -500G) to low acceleration with wide pulse width, difficult to achieve with conventional Shock Test Systems and Vibration tests for not only IEC, MIL and JIS but also requiring higher acceleration, velocity and displacement than ordinary VTSs can be carried out with one system.
