Electric Vehicle Test Systems
See Also: EV Test Systems, Electric Vehicle
-
product
Temperature/Humidity Vibration Test Systems
EHVC SERIES
The EHVC Series is designed for highly accelerated life testing, the demand of which from customers is increasing today. This is a joint system of the AGREE chamber and thermal shock chamber that we have manufactured and makes the temperature rate up to 20℃/min feasible with a compressor only. With this feature, the highly accelerated life test such as AGREE tests, most thermal shock tests can be performed with one unit.
-
product
AC Hysteresis Graph Test System
DX-2012SA
Under continuous frequency of 1 kHz to 500 kHz, automatic measurement of magnetic hysteresis loop of the soft magnetic materials such as silicon steel, precision alloy, non-crystal and ferrite, accurate measurement on the dynamic magnetic characteristic parameters such as amplitude permeability µa, loss angle d, loss iron Pc, remanence Br and coercivity Hc.
-
product
Slip Ring Test System
This is a high specification tester that will measure many cable parameters. It measures cable resistance very accurately using the Kelvin 4-wire method. It also tests for shorts between pins at a low voltage. The next test is to measure insulation between connections at a higher voltage. This is carried out at up to 1500 Volts DC with resistances of 10 to 500 Meg ohms.
-
product
Testing of Electrical Safety
Manufacturers and operators of electrical equipment are required to carry out an electrical safety test within the framework of the applicable regulations. This is to prevent accidents caused by malfunctions in electrical equipment, such as fire, explosion as well as injuries and personal damage. The tests to be carried out are specified in national (VDE/DIN) and international (EN/IEC) standards. After passing the test, the product is considered safe for the entire life cycle, provided it is left in its original condition and used for its intended purpose.
-
product
Electrical discharge detector
SKF Condition Monitoring Center
Detect electrical discharges in electric motor bearings
-
product
Electrical Safety Wall
AllWin Instrument Science and Technology Co., Ltd.
1. Electricity Safety Wall2. 50/60HZ3. Four detection ways4. Continuous testing
-
product
Portable Three Phase Electric Meter Test Bench
GF302D
Beijing GFUVE Electronics Co.,Ltd.
The Portable Three Phase electric Meter test bench is used for grid corporation to cablibrate 3 phase electric meter error. It can test three meters error at one time.
-
product
Bare Board Electrical Testing
ProbeMaster
ProbeMaster is the complete software solution to your shops needs in bare board electrical testing. ProbeMaster is PentaLogixs top-of-the-line software package that combines all of the power of the PentaLogix CAM and Fixturing packages with support for moving probe, Netlist Comparison and other robust features.
-
product
Electricity Metering Device
Mk7A
Built on the advanced Atlas metering platform, the Mk7A is a single phase 2-element meter which integrates both a 100A UC3 compliant relay and 40A UC2 compliant load control relay which allows disconnection and reconnection of electrical services remotely.
-
product
Robotic Vehicle Gap / Flush Measurement System
Automation
LaserGauge® Automation is a robotic system for measuring vehicle gap/flush on a moving assembly line. It is cost-effective, fast, flexible, and delivers LaserGauge® accurate measurements. Utilizing the Cross-Vector scanning and Blue Laser Technology, the system provides more assembled-panel surface information than any other robotic laser profiler.
-
product
Real Car Transient Test System
RealCar Simulation Bench
This system is suitable for transient test of actual vehicle in combination with the real-time model calculation by the measurement/control panel and low inertial motor. By replacing the wheel of the actual vehicle with the tire type bearing, the axle shaft is taken out to the outside of the vehicle and connected to the low inertia motor. It can be reproduced the sliding motion which the chassis dynamometer cannot be realized. Also, since the longitudinal force is not occurred in the vehicle, the vehicle restraint can be simplified and the behavior such as shift shock can be reproduced on the bench.
-
product
Grid-Connection Testing System
This system is a power supply test system that performs grid-connection testing of distributed power sources (solar cells, fuel cells, gasoline engines, etc.)Enable inverter device testing that complies with the Agency for Natural Resources and Energy’s “Guidelines for System Interconnect Technical Requirements” and the Japan electrical Safety & Environment Technology Laboratories (JET) publication “Testing Methods for Small Solar Cell Power Generation System and System Interconnection Safety Devices”.
-
product
Power Device Testing System
Devices that control electric power, and are used in automobiles and a wide range of electrical products.
-
product
USB PD Test System
6050
Single Output USB PD USB PD basic version：the single-group test systemarchitecture is as shown in the table, 5302A AC Source, 3302F + 3310F series and9922-R Quick Charge Controller.
-
product
Automatic Tablet Testing System
UTS 4.3
The UTS 4.3 LAB is a universal and fully automatic tablet testing system based on the long-proven UTS 4.1 - this was developed for industrial use and can be found in production worldwide. The UTS 4.3 LAB is now equipped with the database-driven, intuitive all-in-one touch software and no longer requires additional software solutions for most areas of application.The functionality of the software can be extended modularly and individually adapted to your needs and requirements. FDA regulations can be fulfilled with the optional FDA-21-CFR-Part-11 module.With UTS 4.3 LAB – as with the proven UTS 4.1 IPC – you can test round, oval, square and rectangular tablets as well as numerous special shapes. For difficult oblong tablets, the globally used Oblong Centering System (OZB) can also be integrated.
-
product
Relay Protection Test System
RELAYSTAR 1600
HAOMAI Electric Power Automation Co., LTD.
Relaystar-1600 the 6 phase universal relay protection test kit6-phase current (6×40A) + 6-phase voltage (6×150V) output.
-
product
Digital Electrical Network Analyzer
1826 NA
Standard Electric Works Co., Ltd
● Microprocessor-controlled.● Measures Earth Resistance without the need for poles in the ground or external measuring wires.● Earth measurement uses the real earth current path and the current generated by the electric network, without the need for any disconnection.● The Earth Resistance displayed is exactly the earth resistance that the earth current will need to go through if an earth fault occurs. No need to add all the bonding points and connection paths resistances.● Displays voltage supply at the transformer (Line to Neutral), without loading the transformer. Displays voltage between Line (Phase) and Earth (Ground), without drawing any current.● Measures the impedance of the line itself so you can analyze and differentiate between the multiples paths of the wiring.● Measures the Neutral Impedance. Single one smart push button operation; ON, Test, Scroll trough results and menus.● Checks wiring integrity (LEDs).● Auto off/auto ranging (software ranging). ● Combined prospective short circuit current, loop, individual wire and Earth Tester.● Voltage test L-N and L-E.● Loop test for L-E and L-N and PSC.● Enables analysis of constituent components in L-E and L-N loops giving resistance of earth, neutral wire, live wire and transformer winding.● Display can be customized for large orders.
-
product
EV Battery Test System
Shenzhen Sinexcel RE Equipment CO., Ltd
5V cell equipment adopts Sinexcel innovative circuit design + high-speed DSP complex algorithm, the detection process supports multi-gear switching; The equipment integrates voltage, temperature, pressure and other auxiliary channels, 20ms high-speed working condition simulation and other practical innovative functions to meet all aspects of battery electrical performance testing.
-
product
SIP-90-2 Test System Interface Probe
SIP-90-2
Overall Length (mil): 700Overall Length (mm): 17.78Rec. Mounting Hole Size (mil): 55Rec. Mounting Hole Size (mm): 1.40Recommended Drill Size: #54 or 1.40 mm
-
product
System Level Test
SLT
As technology nodes continue to evolve and with a more aggressive time to market to bring devices to their end applications, full test coverage of such chips is possible only with System Level Testing.
-
product
High Energy Shock Test System
KRD13 series
KRD13 series high energy shock test system is specially designed to meet the requirements of military and automotive testing. The system adopts the principle of pneumatic energy storage expansion. By adjusting the inflation pressure, various high-level acceleration tests can be easily implemented in a short stroke.For the high-G classic shock test, it’s equipped with the corresponding shock amplifier to complete high-peak shock test.
-
product
GPS based Smart Vehicle Tracking Solutions
AzTrack
azTrack is a GPS tracking device for real-time tracking of vehicles and other moveable assets. This is a rechargeable device that can be mounted on to a vehicle or any moving asset on the go.
-
product
Electrical Test Equipment Calibrators
The industry leading series provides by far the fastest and safest solution for calibration of Loop, RCD, PAT's and insulation testers.
-
product
System on Demand (SoD): HiL Test System
System on Demand (SoD) is a unique, agile and standardized principle to design HiL test systems. SoD shifts the focus away from technical-only solutions to a proven automated design process – targeting our customer‘s real issues: time, budget and flexibility.
-
product
ELECTRIC BRAKE FORCE METER WITH DYNAMIC LOAD SIMULATION AND CIRCUIT TESTING
MDTT9107
*Tests truck-side brake controller output and all towing-lighting functions without a trailer*Displays real-time brake controller output gain and timing*Quickly troubleshoots electrical circuits and ground condition*For use with aftermarket and integrated brake controllers*Microprocessor controlled; simulates trailer brake loads*25' cable allows one-man, in-cab testing of brake controller and all truck-side tow circuits*Use to verify that the vehicle’s adaptive (speed/load sensitive) brake-controller output is functioning properly
-
product
Launch Vehicle Avionics
L3 Cincinnati Electronics (L3 CE) began contributing to launch vehicle success in 1953. L3 CE products include an extensive family of command/receiver, command/receiver/decoders, S-Band transmitters, video and other operational products. L3 CE has been on all major U.S. launches.
-
product
IPX3 IPX4 Rain Test System
CX-RIP3/4
Shenzhen Chuangxin Instruments Co., Ltd.
For checking the protection against water with spray nozzle of 0,4 mm bore are used to prove the degrees of protection for the second characteristic numerals 3 and 4 “Protection against Spraying Water” resp. “Protection against splashing Water”.
-
product
Optical / Electrical Clock Recovery
N1078A
N1078A Optical/Electrical Clock Recovery provides standards-compliant clock recovery capabilities for single-mode optical as well as electrical signals from 125 MBd up to 64 GBd PAM4 and NRZ
-
product
Motor Vehicle Testing Benches
Foshan Analytical Instrument Co, Ltd.
Reliable and endurable air bag lifting mechanism. Intellectualized instrumentation controlled by microprocessor. Standard RS-232C or 485 serial communication interface is built in the instrument. A super-bright LED digital display is used, so the reading is clear.
-
product
MirrorLink Test System
Catena 2210
The Catena 2210 is a test tool with two USB Network Control Model ("NCM") devices. These devices create a bridge between two USB hosts. Validation testing is made possible by connecting a test control computer to the USB host being tested. Ethernet traffic from the test host is transferred through the Catena 2210 device to the control host, and vice versa.
