EM
-
Product
Antenna, Biconical
EM-6912A | 30 Mhz – 300 MHz
-
A balun, feedline, and element cage give the Electro-Metrics EM-6912A response curves that are almost linear, making it ideal for swept measurements. An added benefit is that the EM-6912A has an improved BALUN design, which makes it insensitive to changes of orientation while vertically polarized. Readings obtained will be the same no matter which element is closest to the ground plane, eliminating a potential source of measurement error.
-
Product
Omni-Directional Antenna
EM-6116 | 2 GHz – 10 GHz
-
The EM-6116 is a vertically polarized, omnidirectional antenna covering the frequency range 2 to 10 GHz. It is enclosed in a weather resistant radome. Smaller than other similar antennas, the EM-6116 is ideal for covert applications.
-
Product
Ultra Low Level DC Voltage Amplifiers
-
The EM A10 is a low level amplifier module for sensitive measurements, data collection and systems, where signals below 1 nanovolt may be measured. It is ideal for the input unit for precision voltage measuring systems, requiring voltage sensitivity for measuring low noise and low impedance sources. The noise level of the A10 is equivalent to a perfect resistor of about 20 ohms. When used with a digital voltmeter, steady one nanovolt digits may be displayed, with a response time constant of less than a second. The input voltage stability of the A10 is very high, with the drift around a nanovolt per degree C. The input connectors are made from pure copper. The input impedance is very high, and is time dependent, determined by the loop gain.
-
Product
Calibration
EMC Test Antennas
-
There are some changes in the calibration standard ANSI C63.4 concerning the calibration procedures of hybrid antennas, also the newly issued standard - CISPR 16-1-6 dealing with EMC antenna calibration is covered by our services. You are very welcome to consult Seibersdorf Laboratories calibration experts for the recommended calibration procedures of the most common radiated emission test standards.
-
Product
Anechoic Chamber
EMC-3
-
A 3 meter test range ensuring fully compliant Emission and Immunity testing. Ferrite and hybrid pyramidal absorbers are combined in a unique pattern within a SmartShield high performance chamber. Operating at a 3m test distance, this chamber is compliant to CISPR-16 with a measurement zone diameter of 1-2 meters.
-
Product
Antenna, Log Periodic
EM-6952-1 | 1 GHz – 2 GHz
-
The Electro-Metrics EM-6952-1 Log Periodic Antenna operates over the 1 to 2 GHz frequency range. The EM-6952-1 is capable of operating either as a transmitting or as a receiving antenna over the frequency range of 1 to 2 GHz. Its linearly polarized designed permits separate measurement of horizontal and vertical electric field components over its established range. Enclosed in a weather resistant radome, this antenna is suitable for indoor or outdoor usage.
-
Product
Probes, Magnetic Field
EM-6882 | 20 MHz To 230 MHz
-
The EM-6880, EM-6881 and EM-6882 Magnetic Field Probes operate in conjunction with any 50 ohm input impedance receivers.
-
Product
BASIC-programmable IoT Board
EM1001
-
Our flagship BASIC/C-programmable IoT board. Ethernet, as well as optional Wi-Fi and GPRS connectivity. Four serial ports supporting full-/half-duplex RS232, Wiegand, and clock/data modes.
-
Product
Electromagnetic Express
EM-X
-
Is a physics modelling package for electromagnetic fields and charged particles. A CAD component allows the definition of mechanical parts and assignment of electric potentials, magnetization and charged particle sources. A time domain, particle-in-cell (PIC) tool then solves the electromagnetic fields and moves the particles within them. The particles’ own charges andmotions are fed back into the electromagnetic fields allowing the effects of space charge and selfmagnetism to be accounted for.
-
Product
Antenna, Ridged Guide
EM-6961 | 0.9 GHz – 18 GHz
-
The EM-6961 Double Ridged Guide Antenna is a linearly polarized broadband antenna designed and built specifically for EMI measurements and specification compliance testing.
-
Product
Test Fixture, Shielding Effectiveness
EM-2108 | 1.5 GHz – 10 GHz
-
The EM-2108 is a standard test fixture for evaluation of the electromagnetic shielding effectiveness (SE) of planar materials.
-
Product
Antenna, Log Periodic
EM-6946 | 300 MHz – 3 GHz
-
The EM-6946 offers an exceptional combination of frequency coverage of 300 MHz –3 GHz and high power handling capability without compromising the consistent performance versus frequency that makes the log periodic antenna so desirable for test applications.
-
Product
Compact EMC Test Chamber
EMC-3C
-
This compact 3 meter test range will settle into test areas of limited space while continuing to produce exceptional performance for EMC measurement. Emission quiet zones of up to 1.5m are accommodated with very repeatable results. Suitable for EMC pre-compliance emissions and compliant immunity testing.
-
-
Product
EMS Test System
TS9982
Test System
The R&S®TS9982 is the base system for conducted and radiated EMS measurements. Due to its modular design, it covers a wide range of applications and can be very easily adapted to the measurement task at hand. Any configuration is possible – from conducted measurements and the small precompliance system with a compact test cell to the accredited test system for complete motor vehicles with 200 V/m.
-
Product
Probes, Clamp-On
EM-6987 | 1 KHz – 110 MHz
-
The EM-6987 is capable of measuring signals and noise superimposed on power currents up to 300 A from DC to 400 Hz. Intermodulation effects on current probe output are also negligible.
-
Product
Omni-Directional Antenna
EM-6104-1 | 20 MHz-18 GHz
-
The EM-6104-1 is an omni-directional, dual band, hybrid antenna covering 20 MHz-18 GHz. The antenna features wide frequency coverage making it an excellent choice for a variety of applications such as general purpose measurements as well as wideband security applications. This lightweight antenna is ideal for deployable applications that require wideband coverage in a very small footprint. The antenna’s elements collapse for convenient storage and transport. The antenna is configured to mount on a standard ¼-20 tripod stud. The EM-6104-1 Omni-Directional antenna is supplied with an EM-6089 Battery Pack.
-
Product
Antenna, Dual Ridge Horn
EM-6963 | 18 GHz – 40 GHz
-
Model EM-6963 can be individually calibrated for use in EMI/EMC compliance measurements as well as for general purpose measurement antennas over its specified frequency range.
-
Product
Probes, Clamp-On
EM-6980 | 20 Hz – 50 KHz
-
Current probes enable you to measure conducted current without direct connection to the circuit under test by clamping around the conductor, current carrying wire or structural member being tested.
-
Product
Probes, Magnetic Field
EM-6880 | 9 KHz – 520 KHz
-
The EM-6880, EM-6881 and EM-6882 Magnetic Field Probes operate in conjunction with any 50 ohm input impedance receivers.
-
-
Product
Probes, Clamp-On
EM-6981 | 9 KHz – 110 MHz
-
Current probes enable you to measure conducted current without direct connection to the circuit under test by clamping around the conductor, current carrying wire or structural member being tested.
-
Product
EMS Energy Metering System
-
The EMS2005 (Energy Metering System) device series is used for determining the energy quantity in raw biogas, natural gas, or liquefied petroleum gas.
-
Product
Differential Manometer
EM152
-
UEi Test & Measurement Instruments
Dual input manometer with easy-to-read display, intuitive interface and built-in magnet makes this manometer convenient to use
-
Product
Antenna, Double Ridged Guide
EM-6968 | 2.5 GHz – 7.5 GHz
-
The EM-6968 Double Ridged Guide Antenna is a linearly polarized broadband antenna for specification compliance testing. The versatile EM-6968 is constructed of rugged aluminum, which makes it excellent for use under severe field conditions and the size makes it suitable for use in the limited space of a shielded enclosure.
