-
Product
ICT/FCT-Fixtures Max UUT370 × 300 mm (wxd)
CK-2 Large (Hold-Down Gate) / 230158
-
The series of In-Circuit testers that are Teradyne for the 228x and TestStation are dedicated tools that rely on the tester hardware for diagnostics and test pattern delivery. The integration of the stand-alone BTS with the Teradyne ICT can enhance the system’s capability. In other words, it can provide access to additional tools. It provides the user with a common platform and portability of test patterns from stand-alone to ICT and later on to functional test and depot test stations.
-
Product
GB-GRAM/GB-GRAM-M Interface Card
Valiant 153M
-
Valiant 153M is a GB-GRAM/GB-GRAM-M (GB-GRAM/M) interface card that allows the simultaneous operation and testing of a commercial- off-the-shelf (COTS) receiver and a GB-GRAM/M. Both receivers are powered and communicate using a single USB mini cable. By integrating a COTS receiver onto the Valiant 153M, users can perform cross-checks to determine if the military receiver is connected and communicating data properly. Both receivers communicate via the onboard USB mini or RS-232 serial connectors. The Valiant test fixture was designed to be nearly the same size as the GB-GRAM/M type I card.
-
Product
Through Connector Functional Test Fixtures
-
Circuit Check is a pioneer in the development and implementation of access mechanisms enabling testing of circuits through on-board connectors.
-
Product
Hand Held Test Fixtures
-
Manual, or semi-automated mechanical devices designed to secure a Device Under Test (DUT) and provide a stable interface for electrical testing, inspection, or programming.
-
Product
Drop-In Functional Test Fixtures
-
Circuit Check’s drop-in base fixture and replaceable personalized plates are the ideal solution where production volumes are lower and the need to change from one fixture and test program to another occurs quickly. Interchangeable test fixture drop-ins enable the same test system to be quickly reconfigured with different tooling and probe patterns for different products. This maximizes equipment re-use, while minimizing the cost for each new test. With Circuit Check’s base fixture and drop-ins, the wiring and test electronics are not disturbed, thus ensuring configuration consistency each time the system is re-tooled.
-
Product
Resistivity Cell For N1413 (26/50 Mm Electrodes)
N1424B
Resistivity Cell
The N1424B is designed to operate specifically with the B2985B/87B Electrometer/High Resistance Meter. It is used to measure surface or volume resistance/resistivity of insulation materials. The N1413A High Resistance Meter Fixture Adapter is required to connect the N1424B to the B2985B/87B.
-
Product
Wire/Cable Harness Tester
PANTHER 4HT
-
Qmax Test Technologies Pvt. Ltd.
The Panther 4HT Wire \ Cable Harness tester is designed for Automotive and Semiconductor industry to apply in testing of wire harnesses, that needs testing during production with whole new fleet of features that make the task reliable, complete and fast. It uses innovative technology to test the impedance values. It can be interfaced to any type of fixtures as required. It uses the Learn and Compare technique for finding out opens or shorts in a harness. The learnt open / short combination from a Good Board is taken as reference and compared with the Board Under Test for any mismatch.
-
Product
Rotary Table Handler
6000 Series Rotary Handler
-
Rotary table handlers are an excellent choice for PCBA or product – level test, programming, part marking, automatic part rejecting, and vision inspection in order to satisfy manufacturing applications that require high throughput. Rotary table based systems used in production can also help reduce the impact of load and unload times for the operator, because the device-under-test (DUT) automatically moves to the next cell within the station as each DUT is loaded. Circuit Check’s 6000 series handlers are modular, scalable and flexible, supporting high-mix and high-volume production needs. A common application example is to configure a 6000 series as a rotary station to perform simultaneous PCBA bar code scanning, testing, programming and marking, in a pipe-line process which improves throughput requirements. The 6000 series handlers leverage Circuit Check’s unique quick-change fixture drop-in technologies to allow for station modularity and scalability. Production line flexibility is achieved because the 6000 series handler is software and hardware agnostic, enabling adaptability to a variety of applications, and is limited only by the number of stations.
-
-
Product
Automatic Fixture Removal
S95007B
-
Many devices do not have coaxial connectors and so they are put in fixtures in order to measure them in a coaxial environment. You must accurately remove the effects of the fixture to get a good measurement of the device under test (DUT). This option adds a powerful application wizard to guide you through characterizing a fixture and removing it from the measurement. The S95007B software is compatible with M980xA PXI Vector Network Analyzers.
-
Product
Manual Fixture Kit
230355 – CMK-06
-
Linear click system with ball bearings, using gas springs.10 mm ESD-proof top cover with aluminum reinforcement bars.Steel base cabinet with detachable aluminum back and bottom panels.Detachable interchangeable case system with an 8 mm spring-loaded probe protection cover.Base cabinet fitted with a telescopic guide rail and catch.
-
Product
Topside Probing for Functional Test Fixtures
-
Circuit Check matches top side test targets to your specification and needs. The Signature Series pneumatic drive fixture is the industry standard for precision, accuracy and repeatability.
-
Product
DC Power Module, 35V, 1.5A, 50W
N6734B
Power Module
The Keysight N6734B is a 52.5 W basic DC power module that provides programmable voltage and current, measurement and protection features at a very economical price, making these modules suitable to power the DUT or to provide power for ATE system resources such as fixture control.
-
Product
Utility Card: Flash Programming Applications
-
This new feature enables the Keysight Medalist i3070 ICT to perform higher speed flash programming at the ICT station in the printed circuit board assembly manufacturing line. You can combine programming and testing into a single phase, to save time and money. This in-system programming (ISP) flash solution is tester-based and does not rely on fixtures, thus enabling greater flexibility and ease of debugging.
-
Product
Custom Fixtures
-
Joule mechanical design and manufacture capabilities allows us to create other custom projects to meet your test needs. Joule can design burn-in racks, jigs and stand-alone test station.
-
Product
Test Solutions Services
-
Spinnaker Contract Manufacturing, Inc.
As standard practice, all of our SMT assemblies are washed and tested through our Automated Optical Inspection and pass through our stringent internal QA/QC policies. In Cables and Wire Harnesses, pretests, such as pull tests and crimp type tests, are performed on all builds before being tested for continuity, hi-pot, shorts and mis-wires, to name a few. Our electromechanical assemblies are capable of receiving full functional testing through custom test fixtures and RF test. Some RF tests include Gain/Loss, Frequency Response, VSWR (Voltage Standing Wave Ratio), Inter-Modulation Distortion and Output Power.
-
Product
Resistivity Cell For N1413 (50 Mm Electrodes)
N1424A
Resistivity Cell
The N1424A is designed to operate specifically with the B2985B/87B Electrometer/High Resistance Meter. It is used to measure surface or volume resistance/resistivity of insulation materials. The N1413A High Resistance Meter Fixture Adapter is required to connect the N1424A to the B2985B/87B.
-
Product
Voltage Tester
-
PeakTech Prüf- und Messtechnik GmbH
Uses voltage detection technology for the detection of voltage in cables, cords, circuit breakers, lighting fixtures, switches, outlets and wires.
-
Product
MMI-DVH, Mechanical Test Fixture
100360
-
Mechanical test fixture with optimised ergonomics for function tests, end tests and ICT applications. The MMI is prepared for safety switches with guard locking as well as for electrical interlocking. Our MMI-DVH test fixture is versatile and has a special cover height (internal cover dimension 114.5 mm). Reinforced version!
-
Product
Manual Fixture Kit
230356 – CMK-07
-
Linear click system with ball bearings, using gas springs.10 mm ESD-proof top cover with aluminum reinforcement bars.Steel base cabinet with detachable aluminum back and bottom panels.Detachable interchangeable case system with an 8 mm spring-loaded probe protection cover.Base cabinet fitted with a telescopic guide rail and catch.
-
Product
MMI-HVI
100183
-
The MMI-HVI is a good basis for fixtures with higher voltages. The MMI-HVI is made of NON-dissipative plate material and can therefore be used in the low-voltage range (up to 1000 V AC / 1500 V DC). The earthing package included is an important component. This is because the housing earthing, the earthing connection and the earthing test ensure that the safety standards are met. The solenoid interlock and the safety switch ensure access protection.
-
Product
ICT/FCT-Fixtures, Max UUT 250 × 180 mm (wxd)
CK-1-228X-S (Small IF) / 230514
-
The series of In-Circuit testers that are Teradyne for the 228x and TestStation are dedicated tools that rely on the tester hardware for diagnostics and test pattern delivery. The integration of the stand-alone BTS with the Teradyne ICT can enhance the system’s capability. In other words, it can provide access to additional tools. It provides the user with a common platform and portability of test patterns from stand-alone to ICT and later on to functional test and depot test stations.
-
Product
EEE Component Testing and Screening Services
-
DPACI performs 100% screening as well as qualification testing on electronic parts supplied to the high reliability commercial, industrial, space, and U.S. military sectors. We generate software and hardware to test microcircuits, discrete semiconductors, hybrids, PEMS, and other EEE electronic components to exact customer and military specifications. Our engineering experience in electronic parts screening, qualification, and in-house test fixture fabrication allows us to provide value added components in a timely manner.
-
-
Product
Incremental Length Gauges For Measuring Stations And Multi-gauging Fixtures
SPECTO series
-
*High system accuracy: ±1 µm*Very rugged design*Compact design for limited installation space*Various plunger actuation possibilities*Highly durable ball-bearing guide*Measuring range of up to 30 mm*Interfaces: 1 VPP, TTL*Protection rating of up to IP67
-
-
Product
Test Fixture Kits
Test Fixture
More then ten years of experience in special, customized engineering and manufacturing brought us to the highest level of creating reliable, flexible and robust Test Fixtures. Currently our HQ is located in Vecsés, Hungary together with our R&D. Equip Group has Test Fixture Kit manufacturing plant in Serbia, focusing on supplying competitive, high – quality and high – volume products for the global market.With more then 180 employees, Equip – Test is able to offer our customers turnkey solutions in fixturing with test program generation. No matter if you have a simple or complex, high-density PCB (Printed Circuit Boards), or if you have DUT (Device Under Test) already assembled into metal or plastic housing, we can offer you a very stable technical solution.
-
Product
Parametric Test Fixture
U2941A
Test Fixture
The Keysight U2941A is a parametric test fixture that is designed to complement the usage of U2722A USB source measure unit in the testing of semiconductor components, including SMT and DIP ICs.
-
Product
PXI 5A Fault Insertion Switch 10-Channel
40-196-001
Fault Insertion Unit
The 40-196 is a 10 Channel 5A Fault Insertion Switch, primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers. It is designed to be able to insert different fault conditions between the test fixture and the equipment under test: Open-Circuit, Short-Circuit between signal pairs, Short-Circuit between signal pairs and user applied fault conditions e.g. Power or GND. Shorting relays on each channel enable UUT signals to be subjected to external user applied fault conditions or to be shorted to the adjacent signal in the same channel. Relays in line with the signal allow open circuit conditions to be simulated on either side or both sides of a channel signal pair. The switching topology of the 40-196 allows channels to be interconnected so that complex fault insertion systems can be constructed.
-
Product
Custom Test Fixtures
-
Intrinsic Quality is proud to offer a variety of Test Fixture Development Services that include fixture building, tester interface building, harness building, troubleshooting, maintenance, design, and engineering. IQ’s fixtures are built to exacting specifications and configured to deliver quality production testing. Our global customers have trusted us for over 35 years to provide custom solutions applying leading edge technology. IQ consistently delivers cost-effective solutions with our client’s recognition and gratitude.
