-
Product
VOC FIXTURE OVER CLAMP ASSEMBLY'S
-
Test-X VOC Series overclamps are used for testing bare or loaded printed circuit boards with open vias and to minimize board flex.The VOC Series overclamp comes with adjustable delrin pressure fingers, anti-rotating hex nuts, hinge and latching assemblies, mounting instructions and hardware.The VOC Series will accomodate fixtures with dress frames or newer style fixtures using full-size top plates.
-
Product
DDC (Dual DIMM Carrier) DIOS Adaptor
JT 2702/DDC
-
The JT2702 Digital 256 channel JTAG I/O module. JT2702/DDC (Dual DIMM Carrier) is a DIMM DIOS accessory product. It is typically used in custom test adapters or fixtures where a large number of digital I/O channels are required with a minimum space overhead.
-
Product
Clamshell Type Mechanical Fixtures
Series 30
-
Semco’s GR Series 30 mechanical kits are an inexpensive solution to printed circuit board testing that requires the benefits of GR2270 style (VG) interface compatibility.
-
Product
Boundary Scan Test
-
Boundary Scan is a very useful tool for quick, low-cost, re-usable powered-up test of an assembly for basic functionality. Because a fixture with test probes is not required, it is possible to have a working test available within hours or days, rather than weeks. Designers can receive rapid feedback on their prototype boards with tests that can be used again during production testing, as well as for device programming. Given power, ground and Tap port signals, tests can be written to assess the performance of the boundary scan enabled parts on an assembly and other parts on the boundary scan chain.
-
Product
A Popular Combination Of Flex 10 And Flex 20 In A Compact Footprint
Flex 30 ATE
-
A combination of both the Flex 10 and 20 system, the Flex 30 is floor mounted system that maintains a small footprint whilst offering that useful additional space. Generally it is fitted with either the G12 or G12X VPC interface allowing a large number of mixed signal connections to be routed to the test fixture.
-
Product
Steering Test Equipment: Software & Hardware
-
MB Dynamics delivers steering test equipment to help fulfill a myriad of application test requirements, or jobs-to-be-done. The steering test equipment consists of software for multi-test-head, synchronized MIMO closed-loop control and data acquisition; rotary servo motors for attachment to a steering spline or wheel; electrodynamic shaker systems; long-stroke linear motor actuators; pneumatic actuators; column stands for mounting steering column; gear fixture for mounting the gear; instrumentation (force, torque, displacement, rotary position, acoustic, acceleration); fixtures for mounting gears and columns; brackets, clamps, and fixtures for holding test items; jounce/rebound fixtures and tilt positioners for aligning input forces with tie rods at angles; software and associated data acquisition hardware up to 16 channels for recording, analysis and evaluation of in-lab steering noises and accelerations, road load data acquisition, and general Sound & Vibration analysis; and engineering services to accelerate test effectiveness.
-
Product
DC Power Module, 20V, 15A, 300W
N6773A
Power Module
The Keysight N6773A is a 300 W basic DC power module that provides programmable voltage and current, measurement and protection features at a very economical price, making these modules suitable to power the DUT or to provide power for ATE system resources such as fixture control.
-
Product
In-Circuit Tester
Eagle MTS180
-
The Eagle offers low testing cost for high volume with even the most complex fixture applications. Equipped with a Press-Down-Unit and a combination of analog and hybrid In-Circuit test pins, the MTS180 is in a class for its own. Furthermore, the tester can be equipped with functional test modules to provide even higher fault coverage and thus satisfy the test requirements of a larger number of customers.
-
Product
PCIe
SFF 8639 Gen4 (U.2)
-
SCHILLER AUTOMATION GmbH & Co. KG
The 8639G4-TPA-PR test adapter or test fixture kit facilitates Source and Sink compliance testing for SFF-Hosts and Devices. These SFF-8639 Gen4 fixtures utilize the multifunctional connector system supporting single/dual port SATA, dual and MultiLink SAS, and/or up to four (4) port PCIe device configurations. The SFF-8639 Gen4 receptacle fixture will accept devices with plug connectors that are in accordance with SFF-8482, SFF-8630, and SFF-8680.
-
Product
Bottom Electrode SMD Test Fixture
16198A
Test Fixture
Designed for impedance evaluations of bottom electrode SMDs and supports 201 (mm) and 402 (mm) sizes
-
-
Product
Flying Probe Testers
-
SPEA’s Flying Probe Testers help manufacturers of printed circuit boards to deliver top-quality products in the fastest time-to-market, avoiding fixture cost and increasing accessibility when compared to bed-of-nails testers.
-
Product
Stand-Alone Test Fixture
MA 2013/D/H
-
Parallel contact stroke: 15 mmContact force max.: 2000 NInterface block required: NoInterface signals max.: 1700Component on PCB: 58 mmPressure frame unit-opening angle: 75Installation height test probe top: 16,0 mmInstallation height test probe bottom: 10,5 mmInstallation height dual-stage test probe bottom: 16,0 mmweight: 22,00 kg
-
Product
Material Test Machines
-
Sanwood Environmental Chambers Co ., Ltd.
Sanwood Universal Test Machines, UTM, are widely use for different material testing, like semi-product & finished product made of rubber, plastic, metal, nylon, non-woven fabrics, textile, tape, polyfoam, waterproof materials, wire, cable, etc. With different test jigs or fixtures, the UTM can run the tensile, compression, shearing foce, adhesion, peeling force, tear strength, fatigue, etc test according to GB, CNS, ASTM, ISO, DIN, JIS, EN test standards.
-
Product
G12 - 12 Module Solution
-
For maximum versatility and easy access to instrument-side wiring and cable assemblies, VPC offers a selection of slide kits designed to fit most common rack depths. All slides are rated to support 180 lbs (81 kg) to accommodate even the largest fixtures. To order, measure rack depth between mounting rails. With this measurement choose the slide mounting kit that fits the rack. A rack extender kit is available for mounting to racks with recessed rails.
-
Product
SATA
-
SCHILLER AUTOMATION GmbH & Co. KG
SATA test adapters and test fixture kits facilitate Source and Sink compliance testing.
-
Product
Custom Testing
-
You create a custom test plan (a file that lists a series of tests to be run), to meet requirements specific to your environment and apply that test plan to any number of clusters. You specify the order in which tests run and the specific components to be tested. After you set up your custom test environment, you run the test procedure from SMIT and view test results in SMIT and in the Cluster Test Tool log file. For information about customized testing, see Setting up custom cluster testing.*Fixture Design*Fixture Fabrication*Custom Test Stands*Prototype Testing Services*Product Safety Testing Services
-
Product
Test Fixture with API
TA-14VG
-
The TA-14VG test fixture is based on the requirements for the Integrated Test Procedure for the VG-14A assembly as shown in the OEM maintenance manual. The panel also contains a test point breakout for the units main connector as well as one for the VG-401 base. The VG-401 breakouts provide an in series connection that will allow easy access to the gyro's signals and also provides a way to monitor rotor current. The panel also contains a variac to allow for line voltage adjustment.
-
Product
ATE Test Probes
-
For contacting loaded PCBs in automatic test equipment (ATE) with vacuum, pneumatic or mechanically operated fixtures. Available in 2.54mm, 1.91mm & 1.27mm test centre spacings.
-
Product
PXI Expandable 16x16 RF Matrix 50Ohm Lemo 00
45-720A-541
Matrix Switch Module
The 45-720A module is a 6U 16x16 RF Matrix suitable for switching frequencies to beyond 250MHz. The 45- 720A module is available in 50 and 75 Ohm versions with a choice of coaxial connectors. It is intended for the easy construction of high performance bidirectional matrix switching systems. Automatic Isolation Switches are located on all coaxial connectors, these disconnect the matrix from the external test fixture. This maximises isolation and RF performance.
-
Product
Automatic Fixture Removal Software
S97007B
-
Automatic Fixture Removal (AFR) software is used to remove the effects of the fixture used to test coaxial connectors, which is required to make accurate measurements on the device
-
Product
In-circuit Test
Medalist i1000 Systems
-
Cover Extend Technology (CET) is now supported on the Medalist i1000D. The i1000D only requires a VTEP MUX card to enable CET. If you are already using test fixtures with VTEP MUX cards , you can now implement CET without any fixture modification. Simply add new VTEP probes to devices that were previously not testable. This greatly reduces implementation efforts.
-
Product
Breakdown Voltage Tester
ZDS-50B
-
Shanghai Dean Electrical Co., Ltd
Executive standard: GB/T4074.5-2008/IEC60851-4; Inspection standard: JB/T4279.11-2008Used to test the breakdown voltage performance under room temperature of enameled round and flat wires with nominal conductor diameter of 0.018mm and above;Three voltage rise speeds are available: 20V/s, 100V/s and 500V/s, with error being ±5%;Three test methods can be adopted: round bar method, twist pair method and ball method;Clamp a group of test samples (5 for each) once, available to complete breakdown or withstand voltage test for any of sample one by one or individually; breakdown voltage and withstand voltage time would be automatically saved for future enquiry; all operations would be automatically completed;Capable of conducting high temperature breakdown voltage test in combination with RDS-50 thermal-state voltage tester;LED would automatically display test results and automatically return;During sample breakdown, breakdown voltage indication value would be automatically locked, free from flashing, and the test result is distinct and relatively clear;Equipped with test fixture for round rod method and twist pair method as well as the test weight for round rod method;Equipped with ball method test device (steel balls are prepared by user);Test door is provided with safety interlocking device, compliant with relevant regulations on high voltage testing equipment.
-
Product
Resistivity Cell For N1413 With B2980 Series (26/50/76 Mm Diameter Electrodes)
N1424C
Resistivity Cell
The N1424C is designed to operate specifically with the B2985B/87BElectrometer/High Resistance Meter. It is used to measure surface or volume resistance/resistivity of insulation materials. The N1413A High Resistance Meter Fixture Adapter is required to connect the N1424C to the B2985B/87B.
-
Product
Test Engineering
-
TestEdge engineers have an average of 17 years of engineering experience in test, packaging, and fixturing. This experience is across a wide spectrum of products, customers, and ATE platforms. We have experience in all of the following:Digital, analog, mixed-signal, RF Test programming servicesRemote test capability Semi-automatic test generation Automatic data collection and reduction High performance test fixturing Format independant vector translation High power testing with liquid cooling
-
Product
Benchtop with Drop-In Test System
600 Series Compact ATE Platform
-
The Circuit Check 600 Series Compact ATE Platform with built-in professional fixturing solves the uncertainty of repeatable results that are common with bench testing. With the 600 Series Compact ATE, test procedures can become automatic, with test steps and go/no-go limits easily programmable. Hand-probing is eliminated, replaced with accurate, repeatable tooling and reliable spring-loaded test probe fixturing.
-
Product
Test Fixtures
-
REINHARDT System- und Messelectronic GmbH
Is a fixed state of a set of objects used as a baseline for running tests. The purpose of a test fixture is to ensure that there is a well known and fixed environment in which tests are run so that results are repeatable.
-
Product
Universal Testing Systems (Up To 300 KN)
3400 Series
-
Instron’s 3400 Series universal testing machines offer dependable performance across a broad spectrum of mechanical testing applications, with force capacities ranging up to 300 kN. These systems are well-suited for basic tensile, compression, flexural, peel, puncture, friction, and shear testing, and can be easily configured using a wide selection of grips and fixtures from Instron’s accessory catalog. Built with user safety and efficiency in mind, each system incorporates Instron’s proprietary Operator Protect technology, ensuring a secure and intuitive testing environment.
-
Product
Bi-axial Dynacell Load Cells
2527 Series
-
During tests carried out on servohydraulic machines, elements of the system are subject to acceleration. As a result, in addition to the force applied to the specimen, the load cell also reads forces resulting from its own movement and the mass of the grips and fixtures attached to it. Dynacell is the world's first truly dynamic load cell, designed from the outset for measuring dynamic loads. Dynacell introduces the following advantages:*Reduces dynamic load errors which can be a significant percentage of reading *Increases productivity by allowing higher frequency operation while maintaining test validity *Improvements such as doubling the frequency are common
-
Product
FEA and Strain Gauge Testing
-
Circuit Check began Strain Gauge Testing in 1999 when BGA/SMT technology started replacing PTH components, reducing strain levels was a reactive post fixture fabrication process. We quickly recognized that the “reactionary” process was neither efficient nor were we capable on knowing the lowest achievable strain levels. Our engineering team came up with visual tools utilized during design to easily identify areas of excessive probe force, though still not enough data was generated to identify the lowest possible strain. Finite Element Analysis software models the PCBA and test fixture and applies the pressures from test probes and board supports and indicates the micro strain level applied to the PCBA. Using the FEA software during our design process allows our engineers to modify fixture designs to attain the lowest possible micro strain before fabrication begins.
