Analog I/O
Analog I/O are Devices that have the capability of sending and receiving analog signals.
-
Product
I/O Board With One GbE LAN, VGA And DC Jack For PICO841, PICO843
AX93267
-
*Specifications: 1 x DC jack, 1 x VGA, 1 x Gigabit LAN*Dimensions: 100 x 26 mm*Compliant products: PICO841, PICO843
-
Product
Basic Quad J-Type Analog Thermocouple Amplifier
SEN-30103-J1
-
Analog thermocouple amplifier board based on the AD849x from Analog Devices (successor of the AD597). This quad-channel thermocouple board converts the very low voltage signal from a thermocouple to a highly-linear, 0.005V/C output with either 0V or 1.245V offset (both configurations stocked) while removing unwanted noise from the signal. Many supply and output configurations are available with this board, though the PCB was designed with Arduino in mind. Specifically, the output header will plug directly into a standard Arduino Uno or Mega, with a pin-for-pin match for power supply, ground and analog outputs. With a 5V Arduino, temperatures from 0C to 1,000C are possible with the 0V offset board and -249C to 750C with the 1.245V offset board. If using a 3.3V microcontroller (Due, etc), the board must be supplied with no more than 3.3V to avoid damaging the microcontroller. Temperature measurement range is dependent on the supply voltage. It is possible to supply the board with higher voltages to allow temperature measurement over the entire operating range of the K-Type and J-Type thermocouples, allowing use with more capable data acquisition equipment.
-
Product
SCB-100A Noise Rejecting, Shielded I/O Connector Block
785024-01
Terminal Block
100-Pin Female SCSI to 100-Pin Female Screw Terminal, DIN Rail, Wall, Pane Terminal. Block The SCB-100A is a shielded I/O connector block for interfacing I/O signals to NI data acquisition devices with 100-pin connectors. Combined with shielded cables, the SCB-100A provides rugged and protected signal connectivity. It has a mechanical enclosure that features a magnetic removable lid and pinout diagrams. It also includes pane, wall, and DIN Rail mount options.
-
Product
LVDT I/O Cards
PCIe Synchro Series
-
Computer Conversions Corporation
Our versatile PCIe platform enables the mounting of various combinations of input and output modules. We offer resolutions from 10 to 16 bit and various input and output signal configurations. It is possible to achieve up to 8 input channels or combine input and output modules to suit unique applications.
-
Product
Switched Amplifier With Analog Detector Output
-
Operates at 3 GHz-10 to -5 dBm Input Power to +4 to +7 Output powerAnalog Detector OutputTTL Compatible, 70 dB On-to-Off Ratio, 50 ηSec Response Integrated RF Switch
-
Product
Mixed Signal Oscilloscope: 100 MHz, 4 Analog Plus 8 Digital Channels
MSOX2014A
Oscilloscope
100 MHz4 analog plus 8 digital channels Easily view your signals on the 8.5-inch WVGA display Capture more data with up to 1 Mpts memory See more signal detail with 50,000 wfms/s update rate Expand your measurement capabilities with full upgradability: Add 20 MHz function generator, 3-digit voltmeter, serial trigger and analysis, segmented memory & mask testing at any time Easily set up teaching labs with our free Educator's Resource Kit
-
Product
PXI 4 Slot BRIC 230x8 1-Pole Dual Analog Bus (5 sub-cards)
40-560A-021-230X8-M
Matrix Switch Module
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high-performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
Digital I/O Module with 32 24V inputs
IO206
-
This I/O module is a dedicated digital I/O module providing 32 channels of 24V inputs. The inputs are galvanically isolated by opto-couplers. All channels have a common freely programmable debounce time. Each IO206 I/O module comes with xPC Target driver blocks and Simulink test models, an external shielded 50-pin I/O cable and a terminal board for easy access of all physical I/O signals, and comprehensive documentation.
-
Product
REM-11120, 4-Channel Thermocouple, 1-Channel Voltage, Temperature Input Module for Remote I/O
784750-01
Temperature Input Module
4-Channel Thermocouple, 1-Channel Voltage, Temperature Input Module for Remote I/O - The REM‑11120 is a temperature input module for remote I/O. Remote I/O systems are low-cost, modular systems for simple machine control and measurements. A remote I/O system consists of an EtherCAT bus coupler and individual modules mounted on a DIN rail. You control the REM‑11120 from a real-time controller such as a CompactRIO Controller or an Industrial Controller. You can use remote I/O hardware to add low-cost I/O for simple tasks while your controller handles advanced tasks such as image processing, motion control, and high-speed or specialty measurements. The REM‑11120 also has an adjustable filter time for improved measurement quality and optional external cold junction compensation (CJC) or PT100 resistance temperature detector (RTD) measurements.
-
Product
Mixed Signal Oscilloscope: 33 GHz, 4 Analog Plus 16 Digital Channels
MSOV334A
Oscilloscope
33 GHz analog bandwidth4 analog plus 16 digital channels Capture a longer signal trace with up to 80 GSa/s sample rate and 2 Gpts of acquisition memory Get the best signal integrity with the low noise floor (2.09 mVrms at 50 mV/div) and lowest jitter measurement floor (100 fs)See better measurement accuracy with ENOB values in excess of 5.5 and a SFDR exceeding 50 dBC Access the broadest range of jitter, trigger, analysis and protocol tools (featuring Precision Probe)
-
Product
Analog Multimeters
-
Analog Multimeter is a manual range multimeter perfect for those accustomed to the reliability of an analog tester. The compact, lightweight design of this multimeter makes it easy to transport or carry and use. The 13 position rotary dial increases the accuracy of measurements. Unit measures, AC/DC voltage, DC Current, Decibels and Resistance. Unit offers accurate needle deflection and operates from one AA battery.
-
Product
4/8-CH 12-Bit 1 MS/s Analog Output Multi-Function DAQ PCI Express Cards
DAQe-2500 Series
Data Acquisition Module
ADLINK DAQe-2500 series are high-speed and high-performance analog output multi-function DAQ PCI EXpress cards. The devices are able to update up to 8-CH, 12-bit analog outputs simultaneously at sustaining 1 MS/s. The reference sources and the output polarities are programmable on per channel basis, combining with the multiplying DAC architecture, ADLINK DAQe-2500 series DAQ cards can generate complex modulated analog signals. The hardware-based arbitrary waveform generation frees the CPU intervention even when all analog outputs are updating at full speed, and the lengths of waveforms are only limited by the system memory.
-
Product
32-Ch Isolated DI And 32-Ch Isolated DO USB 3.0 I/O Module
USB-5856
-
USB 3.0 SuperSpeedDaisy chainable by built in USB hub32-ch digital input and 32-ch digital output with 2,500 VDC isolationWide input voltage range (10 ~ 30 VDC)Wide output voltage range (5 ~ 40 VDC) and high output current (350 mA/ch)Quick removable European type connectorLED indicators for I/O statusSupported operating systems: Windows 10/11
-
Product
Jitter Free I/O Access Fast Data Acquisition
TiCoBasic
-
Shortest available reaction time for fast data acquisition, open- and closed-loop control! This focus of Jger Messtechnik is greatly intensified by the new TiCo processor, which enables real-time processing in the scale of nanoseconds. The TiCo (Timing Controller) being implemented into a Xilinx FPGA enhances the approved ADwin systems by a close-to-I/O, extremely fast pre-processing.
-
-
Product
Mixed Signal Oscilloscope: 25 GHz, 4 Analog Plus 16 Digital Channels
MSOV254A
Oscilloscope
25 GHz analog bandwidth (upgradable)4 analog plus 16 digital channels Capture a longer signal trace with up to 80 GSa/s sample rate and 2 Gpts of acquisition memory Get the best signal integrity with the low noise floor (1.73 mVrms at 50 mV/div) and lowest jitter measurement floor (100 fs)See better measurement accuracy with ENOB values in excess of 5.5 and a SFDR exceeding 50 dBC Access the broadest range of jitter, trigger, analysis and protocol tools (featuring Precision Probe)
-
Product
Enhanced 16 Discrete/Switch I/O Channels (±80 V, 625 mA/Ch.)
DT5
-
The DT5 module (the enhanced version) features 16 independent, isolated, programmable channels that can be used for input voltage measurements (±80 V), or as a bi-directional current switch (up to 500 mA per channel). When programmed as a switch with the switch closed, both the current through the switch and the voltage across the switch can be monitored. These modules include diode clamping on each channel. Clamping is useful for inductive loads, such as relays and short circuit protection. Additional features of the DT5 (Enhanced Version) are listed below.
-
Product
Digital Waveform Acquisition, Digital I/O, Pattern Generators
-
Digital I/O cards, pattern or pulse generators and digital data acquisition cards are all focused on digital signals. Input and output signals have two logic levels called low state (0) and high state (1). The electrical representation of these logical levels depends on the logic family and the supported I/O standard.
-
Product
I/O Board With Two COM, Four USB 3.0, VGA And Audio For PICO880, PICO500, PICO300
AX93275
-
*Specifications: 1 x RS-232/422/485, 1 x RS-232, 4 x USB 3.0, 1 x VGA, 1 x Audio (MIC-in/Line-out), 1 x Power On, 1 x Reset, 2 x LED*Dimensions: 118 x 40 mm*Compliant products: PICO880, PICO500, PICO300
-
Product
Sixteen Channel, 12-Bit Analog Input Card
PCI-AI12-16(A)
-
Model PCI-AI12-16 is a multifunction, high-speed, analog-to-digital converter board for use in PCI-Bus computers. It accepts up to 16 single-ended or eight differential inputs. The board uses a low-noise, multilayer printed circuit board. Inputs are protected against overvoltage conditions up to ±35 volts and typically survive static discharges beyond 4000 volts.
-
Product
Mixed Signal Oscilloscope - 1 GHz, 4 Analog Plus 16 Digital Channels
MSOX3104T
Oscilloscope
1 GHz4 analog plus 16 digital channels Easily view and analyze your signals with on the large 8.5-inch capacitive touch screen Isolate signals in seconds with exclusive Zone touch triggering See more signal detail with the 1,000,000 wfms/s update rate Capture more data with up to 4 Mpts memory Expand your measurement capabilities with full upgradability: Add 20 MHz arbitrary waveform generator, 3-digit voltmeter, serial trigger and analysis & mask testing at any time
-
Product
Analog Output / Arbitrary Waveform Generator
GX1632e
Waveform Generator
The GX1632e is a 3U PXI Express digital to analog output board designed specifically for applications where multiple DC or AC analog outputs are required. The GX1632e offers 32 output channels with 16-bits of precision signal sourcing performance. Three modes of operation are available including Analog Output, Arbitrary Waveform Generation (ARB) and Data Streaming.
-
Product
96-Ch Digital I/O PCI Card
PCI-1753
-
Emulates mode 0 of 8255 PPIBuffered circuits for higher driving capacity than 8255Multiple-source interrupt handlingInterrupt output pin for simultaneously triggering external devices with the interruptOutput status read-back“Pattern match” and “Change of state” interrupt functions for critical I/O monitoringKeeps I/O setting and digital output values when hot system resetSupports dry contact and wet contactHigh-density 100-pin SCSI connector
-
Product
LVDS I/O Module
LVDS-MOD3
-
Curtiss-Wright Defense Solutions
The LVDS-MOD3 is a front panel mezzanine module designed to provide LVDS I/O functionality to Curtiss-Wright's FPGA-based processing PMC modules. This LVDS I/O module provides 32 differential pairs to the front panel. The LVDS-MOD3 LVDS I/O module is aimed at embedded application development.
-
Product
ATCA I/O Rear Transition Module (RTM)
ART001
-
The ART001 is an I/O expansion ATCA Rear Transition Module (ARTM) that provides GbE, 10 GbE, PCIe and Management I/O for the front blade. The module is designed to mate with any ATCA Carrier. ART001 provides PCIe x8 access via an iPASS connector to the rear. The GbE rear access is provided via six SFP ports and five RJ-45 ports. The module has dual 10 GbE PHY which mates to the host via the zone 3 connector and provides dual SFP+ to the rear.
-
Product
LXI Reed Relay Matrix - Dual 64x8 Plugin, Direct Y Access, 6 Analog Buses
65-223-001
Reed Relay
The range includes four plug-in models covering matrices of up to 1,536x4 in increments of 128 (model 65-221), 768x8 in increments of 64 (model 65-223), 384x16 in increments of 32 (model 65-225), and 192x32 in increments of 32 (model 65-227). Users can specify as many or as few plug-in modules (up to six) required and can field upgrade the chassis to extend the matrix when necessary. Another important feature is that over 1,500 relays can be closed simultaneously for specific conditions for parametric testing.
-
Product
Digital I/O via Ethernet
2610
-
Connects to Ethernet via 2601 communication moduleAll channels may be independently programmed as input or outputEight channels have pulse width modulation outputsRJ-11 I/O connectors eliminate need for external terminal blocksSupport for interlocks and multiple power supplies per channelInput channels are debouncedWatchdog Timer
-
Product
Mixed Signal Oscilloscope - 100 MHz, 4 Analog Plus 16 Digital Channels
MSOX3014T
Oscilloscope
100 MHz4 analog plus 16 digital channels Easily view and analyze your signals with on the large 8.5-inch capacitive touch screen Isolate signals in seconds with exclusive Zone touch triggering See more signal detail with the 1,000,000 wfms/s update rate Capture more data with up to 4 Mpts memory Expand your measurement capabilities with full upgradability: Add bandwidth, 20 MHz arbitrary waveform generator, 3-digit voltmeter, serial trigger and analysis & mask testing at any time
-
Product
Oscilloscope - 100 MHz, 2 Analog Channels
DSOX3012T
Oscilloscope
100 MHz2 analog channels Easily view and analyze your signals with on the large 8.5-inch capacitive touch screen Isolate signals in seconds with exclusive Zone touch triggering See more signal detail with the 1,000,000 wfms/s update rate Capture more data with up to 4 Mpts memory Expand your measurement capabilities with full upgradability: Add bandwidth, digital channels, 20 MHz arbitrary waveform generator, 3-digit voltmeter, serial trigger and analysis & mask testing at any time
-
Product
PXI Analog Output / Current Loop Simulators
-
These modules are aimed at simulating industrial control transceivers, utilizing 4–20mA current loops. The modules include built-in relays for shorts and opens functionality enabling fault insertion testing on every channel and also enable slew rates to be programmed so that different sensors can be effectively mimicked.
