Current and Potential Transformers
current and potential transformer T&M instruments.
-
Product
Stand-Alone Doppler Current Sensor
DCPS
-
The Doppler Current Profiler Sensor (DCPS) is a medium-range, 600kHz current profiler smart sensor. It offers high-quality ocean current measurements and is ideally suited for cabling directly to various systems or dataloggers via serial or AiCap bus. With its integrated compensation for tilting and movement, the sensor is commonly used to measure current from buoys and other moving platforms.The 5400/5400R version of the current sensor is 300m depth rated, the 5402/5402R version is 4500m depth rated, and the 5403/5403R version is 6000m depth rated and intended for commercial as well as research use. It comes with an integrated temperature sensor that can be calibrated on request.As an extension to the DCPS, we now offer the current profiler with an integrated pressure unit called the 5400P. This version enables acoustic wave measurements in addition to profiling currents. Ideal for small observatories, the DCPS sensor is the market's lowest-cost current and wave sensor.
-
Product
Transformer Testing
-
Measuring bridges or electronic burdens can be individually integrated into existing CT/VT test systems. Customized solutions are our core competence.
-
Product
Current Logger0 to 25mA DC
TV-4804
-
The TV-4804 measures current from 0 to 25mA DC and can be connected to a variety of industry standard sensors enabling the logging of a wide range of process parameters.
-
Product
Transformer Ratio Meters
Three Phase Transformer Ratio Meter Standard Series
-
TRT is based on state-of-the-art technology, using the most advanced technique available today. The test equipment can be used to test both single-phase and three-phase transformers, both with and without tap changer in accordance with the requirements of IEC 60076-1.
-
Product
DC Leakage Current Monitor
MDLA-100
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
This DC Leakage Current Monitor constantly observes leakage current of DC circuit like as PV generation system, etc. and lights up the warning lamp with signal output, when the leakage current exceeds the setting value.
-
Product
Current Probe Calibrator
KSZ
-
PMK Mess- und Kommunikationstechnik GmbH
Since Current Probes are often exposed to hard working conditions, a performance check is recommendedbefore every use. These Current Probe Calibrators generate square wave pulses from 0.05 A to 1000 A with an accuracy better 1%. They qualify for calibration and adjustment of Current Probes.
-
Product
AC/DC Current Clamp Meter
CM600
-
Clamp opens up to 1 inch (25.4 mm). One rotary switch operation. Large 4 digit LCD display. AC/DC Voltage measurement up to 600 Volt. AC/DC current measurement up to 600 A.Relative measurement. One touch auto zero.
-
Product
30 A Current Shunt
34330A
-
Measure current safely with this precision 0.001 ohm resistor housed in a plastic case surrounded by epoxy.
-
Product
Current sensors
-
Assistance systems support the driver and assure safety in the latest generation of automobiles. Infotainment systems entertain passengers during car journeys and provide navigation. Seats are no longer adjusted manually, and doors are opened and closed with electric motors. The ever increasing electrification is driven by many other factors besides convenience and safety though.
-
Product
FTIR – Fourier Transform Infrared
-
FTIR stands for Fourier Transform Infrared spectroscopy. It is a powerful gas measurement technology for simultaneous measurements of multiple gases. The ability to detect and measure almost any gas, combined with the robustness and reliability of the technology, makes FTIR ideal for a wide variety of applications.
-
Product
Manually Operated Transformer Oil Test Set
-
We offer Manually operated Transformer Oil Testing Kits to check the DI-electric strength of the insulating Oils as per relevant specifications via. IS 6972. It is a useful equipment for transformer / switchgear manufacturing units. Oil frittering agencies, repair shop and electrical maintenance departments.
-
-
Product
Clamp type AC Current Sensor／for Low Leakage Current Measurements(ZCT Series)
ZCT-18S
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Best sensor for low leakage current measurements of less than 1mA.*Ultra compact size with 18mmφ jaw opening capability.*High sensitivity and least affection from external magnetic field.
-
Product
AC Current Digital Clamp Meters
-
Precision Mastech Enterprises Co.
Handheld, safe, and non-contact electrical tools designed to measure alternating current (AC) without disrupting the circuit
-
Product
Impulse Current Generator
-
Weshine Electric Manufacturing Co., Ltd
Impulse current generator is mainly used to test the ability of electrical equipment to withstand strong impulse current, widely used in lightning arresters and electrical and electronic equipment in operation conditions of oscillation wave immunity test, can also be used for other research tests.
-
Product
Wireless Primary Current Recorder Meter
GF2015
-
Beijing GFUVE Electronics Co.,Ltd.
GF2015 is a wireless primary current recorder equipped with a 433M for transmit the recorded data into the user''s PC by our PC-Link Software. It is a good assistant of power monitor system. The recording interval can be set from 1- 60 min. The PC-Link Software can generate reports and create graphs for profile analysis.
-
Product
Stand-Alone Current Sensors
-
The Aanderaa Current Sensors are based on the backscatter acoustic Doppler principle.
-
Product
Transformer Bench Tester
KVBT
-
KV Hipot Power Test Equipment Co.,Ltd
Transformer Test System is applied for ex-work and maintenance detecting on various transformers.
-
Product
Flexible Leakage/Line Current Tester
RLM-10+
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
●Low-pass filter equipped, it can be cut the noise which is over 150Hz frequency.●Even Coreless Coil but Least Influence from External Magnetic Field and Residual Current●Superior Flexible CT enables Leakage Current Measurement●Backlight Function useful for measurement in the dark place
-
Product
Dual Voltage Buffer with Current Drive
BUF-01
-
The BUF-01 Voltage Buffer is a dual channel buffer capable of driving up to 50 mA of current on each channel at up to ±10 V output. The buffer has a 2nd order low pass filter with 3 dB point of 119 kHz to remove high frequency noise. The unit’s differential inputs are built to withstand high DC over-voltages up to ±50 VDC and greater than ±100 V transients. Gain of the unit is 1 allowing for minimal insertion issues.
-
Product
Through Hole type DC Current Sensor／for DC Leakage Current Measurements
DCZCT-20MH
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*DC earth fault measurement for solar power system*Least affection from the magnetization of core and temperature fluctuation*DC leakage current measurements*Convenient ＋5V single polarity power supply
-
Product
Current Digital Set Point Relay
-
These Digital set point relay for current (type mrd2011-a) are field proven with excellent sensitivity and are with two independent outputs and are used as under current and over current controlling operations. The two independent outputs are programmable in a specific range i. E. The range if it is 25a the settings can be made within the range of 250 a. This facility of having the liberty to set the required current is added advantage in the digital meters of these models available in the market. The set points are field settable within the range mentioned in the model. these relays have inbuilt timers and this facility enables the user to avoid external timers and external wiring. The timers are programmable from 0 second to 20 seconds. The ranges available are up to 2500 a. The dimensions are compact and are of 96 mm x 96 mm x 65 mm only. The auxiliary supply for the relay is 110v ac or 230v ac.
-
Product
Through Hole type AC Current Sensor
CT-30AR
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
For measuring electric power (through hole type)
-
Product
30A, 100MHz High Sensitivity Current Probe
CP031A
-
Teledyne LeCroy current probes are available in a variety of models for a wide range of applications. The full range of Teledyne LeCroy current probes includes models with bandwidths up to 100 MHz, peak currents up to 700 A and sensitivities to 1 mA/div. Teledyne LeCroy current probes are often used in applications such as the design and test of switching power supplies, motor drives, electric vehicles, and uninterruptible power supplies.
-
Product
Constant Potential Generator Power Supply Mains
CP225D
-
Supplemental to its outstanding penetration capacity (up to 47 mm for steel in just 10 minutes), the CP225D includes a built-in multiple X-Ray output carrousel that features a Beryllium window for the inspection of lighter alloys such as aluminum and carbon fiber. The CP225D is one of the most versatile generators on the market and will adapt to an extremely wide variety of applications. In fields as diverse as the construction or petrochemical industries, its power and small focal spot, light weight, compactness and high penetration capacity will be much appreciated.
-
Product
Generator Of Direct Current And Voltage
GPTN
-
The module is intended for use as part of information measuring systems based on the VXI-bus trunk. The module is designed to generate constant current or constant voltage.
-
-
Product
Primary Current Injection Testing
KAM
-
This substation testing device is designed to grant high current output when needed in substation commissioning activities.
-
Product
SparkFun Current Sensor Breakout
ACS723 (Low Current)
-
The low current version of the SparkFun Current Sensor Breakout is a high accuracy board that utilizes the ACS723 for low to moderate AC and DC current sensing applications. The ACS723 sensor uses a Hall effect sensor to output a voltage relative to the current flowing through the IP+ and IP- pins on the board. The advantage of using a Hall effect sensor, specifically, is that the circuit being sensed and the circuit reading the sensor are electrically isolated meaning that, although your Arduino is running on 5V, the sensed circuit can be operating at higher DC or AC voltages!
-
Product
Through Hole type DC Current Sensor／for Load Current Measurements
MOHT-600B Open loop method
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Hall effect measurement for DC/AC/Pulsed current.*For the use of UPS, batteries, switching power supply, DC motor drivers, etc.
