Parasitic Voltage
draw on battery when vehicle is off.
-
product
Dual Channel High Voltage Linear Amplifier
A400D
This unit contains two independent A400 amplifiers that share common ground reference and power supply.
-
product
High Voltage Dry Reed Relays For up to 15 kV
SERIES 62 & 63
ungsten switches with power rating of 50 Watts maximum? Three switch types:5kV stand-off, 3.5kV switching10kV stand-off, 7.5kV switching15kV stand-off, 12.5kV switching? Series 62 has push-on connectors on top face for EHT and solder pins and nylon studs on the underside for PCB mounting
-
product
Surge Voltage Generator
SSG 3000
BAUR Prüf- und Messtechnik GmbH
Cable fault location with the BAUR SSG 3000. Surge voltage generators are used for pre-location and pinpointing of high- and low-resistive as well as intermittent faults in power cables. The energy stored in a high-voltage capacitor is released at regular intervals or as DC voltage. The thus generated acoustic signal at the fault position can be recorded with a ground microphone and a universal receiver.* High surge voltage up to 32 kV* Continuously adjustable voltage* Voltage monitoring through kV meters with 3 measuring ranges* high surge energy in each voltage range
-
product
Voltage Tester
*Simple and user friendly*Check 1.2V - 230V AC & 12V DC directly*Check ground line and phase line and breakpoint of the AC directly*No battery is required
-
product
High Voltage 50 Ω Pulse Generator
TLP-8010C
High Power Pulse Instruments GmbH
*Wafer and package level TLP/VF-TLP/HMM testing*Combines TLP-8010A and TLP-4010C into one system*Can be operated together with TLP-8012A5 and TLP-3011C pulse width extenders*Ultra fast 50 Ω high voltage pulse output with typical rise time 100 ps (0-40 A) and 300 ps (> 40 A)*Up to 80 kW peak output power into 50 Ω load*Built-in HMM pulse up to ±15 kV with 50 Ω configuration*High pulse output current up to ±80 A (short circuit) with minimum 6 dB reflection suppression*High speed 50 Ω trigger output for oscilloscopes (synchronous to high voltage pulse output)*6 GPIB programmable pulse rise times: 100 ps to 50 ns*8 programmable pulse widths: 1 ns to 100 ns (0-40 A), 1 built-in pulse width: 100 ns (> 40 A)*The optional pulse width extender TLP-3011C enables pulse width up to 1.6 µs in 68 GPIB programmable steps (0-40 A)*Optional external pulse width extensions from 5 ns to 500 ns (> 40…80 A) using the external pulse width extender TLP-8012A5*Built-in pulse reflection suppression*Fast measurement time, typically less than 0.2 s per pulse including one-point DC measurement between pulses*Efficient software for system control and waveform data management*The software can control automatic probers for fast measurements of complete wafers*High performance and high quality components
-
product
REM-11120, 4-Channel Thermocouple, 1-Channel Voltage, Temperature Input Module for Remote I/O
784750-01
4-Channel Thermocouple, 1-Channel Voltage, Temperature Input Module for Remote I/O - The REM‑11120 is a temperature input module for remote I/O. Remote I/O systems are low-cost, modular systems for simple machine control and measurements. A remote I/O system consists of an EtherCAT bus coupler and individual modules mounted on a DIN rail. You control the REM‑11120 from a real-time controller such as a CompactRIO Controller or an Industrial Controller. You can use remote I/O hardware to add low-cost I/O for simple tasks while your controller handles advanced tasks such as image processing, motion control, and high-speed or specialty measurements. The REM‑11120 also has an adjustable filter time for improved measurement quality and optional external cold junction compensation (CJC) or PT100 resistance temperature detector (RTD) measurements.
-
product
High Voltage System
HV-2
International Electro-Magnetics, Inc.
*Tests Power Transformers for Continuity, Ratio and Phase. Applied and Induced Potential and No-load Losses.*14 Conductor Switching Matrix will test 7 individual windings, 13 taps of one common winding or some combination thereof. (10 Amp current limit)*The System Control is Windows/Visual Basic based. Menu screens allow full selection of test parameters and sequence. Low voltage tests can be performed first, allowing defective parts to be rejected without proceeding to time consuming induced Potential dwell routines. Test data labeling and data acquisition software can be easily added to the system.
-
product
Combined High Voltage Test Set
is extensively used to measure AC and DC voltage of different electrical devices.
-
product
PXI/PXIe High Voltage Multiplexer, Single 9-Channel, 2-Pole
42-321-124-HI
The 40-321-124-HI (PXI) and 42-321-124-HI (PXIe) are single 9-channel 2-pole high voltage multiplexers capable of hot or cold switching up to 1000 V peak. They are also available in a range of bank sizes with 1 or 2 poles and channel counts between 4 and 48. High quality reed relays are used throughout.
-
product
Low Voltage Wet Sponge
Operates on a single 9-volt alkaline battery. Unit output voltage is 67.5 volts DC. This voltage makes the detector highly sensitive and accurate. Compact and light weight with no bulky battery packs allowing for non- destructive inspection of paints, epoxy paints and coatings 1-20 Mils.
-
product
Retractable Cable + Automotive Voltage Tester With Magnet Adsorption
3703
Peaceful Thriving Enterprise Co Ltd
*Check on 6, 24 and 48V DC systems.*Used as an extension cord for testing electrical circuits in cars , trailer, boats.
-
product
PXI/PXIe High Voltage Multiplexer, Dual 11-Channel, 1-Pole
42-321-105-HI
The 40-321-105-HI (PXI) and 42-321-105-HI (PXIe) are dual 11-channel 1-pole high voltage multiplexers capable of hot or cold switching up to 1000 V peak. They are also available in a range of bank sizes with 1 or 2 poles and channel counts between 4 and 48. High quality reed relays are used throughout.
-
product
Voltage Input Device For FieldDAQ
The Voltage Input Device for FieldDAQ measures up to eight ±10 V channels with 24-bit resolution and simultaneous sample rates up to 100 kS/s/ch. Some models can power sensors, such as pressure sensors, with up to 24 V per input channel. This device offers 500 V channel-to-channel isolation, protecting instrumentation from high-transient voltages. Additionally, the device is IP65 and IP67 rated to be dust-proof and water-submersible, can operate in -40 °C to 85 °C environments, and can sustain 100 g shock and 10 g vibration. It has an integrated network switch for simplified daisy chaining and provides tight synchronization over time sensitive networking (TSN) for distributed data acquisition systems.The Voltage Input Device for FieldDAQ includes the NI-DAQmx driver and configuration utility that simplify configuration and measurements. NI-DAQmx supports NI programming environments as well as Python, ANSI C, C#.NET, and MathWorks MATLAB® software.
-
product
High Voltage Insulating Tester
Suitable for preventive maintenance of gapless arresters.By simply clamping around the ground wire of an arrestor with a clamp CT, it detects leak current and leak current resistance components.
-
product
Voltage Recorders
Voltage Optimisation & Voltage Stablisation have become popular; the Electrocorder range of single & three phase Voltage portable Recorders are extensively used in this area as well as supply voltage analysis.
-
product
Modular Low Voltage Motor Protection
LM10
The GE Multilin LM10 Low Voltage Motor Protection System is a modular device for low voltage motor protection. The compact design of the LM10 is ideally suited for Low Voltage Motor Control Center applications but can also be used in standalone applications. The LM10 comes standard with the DeviceNet protocol that allows the user to control and monitor the relay over a network. The relay also has an interface port to communicate with the optional LM10 Programmable Display Unit (PDU).
-
product
Acute High Voltage Differential Probe, 20x/200x, 100MHz, 1400V
ADP2100
*USB Powered (or Power Bank)*Bandwidth up to 100 MHz*Overrange Indicator*Audible Overrange Alarm*Bandwidth Limit : 5 MHz / Full*Can be used by any DSO which has the USB port(s).*EC Declaration: EN 61010-031:2002 +A1:2008*Double-layer wire for power insulation
-
product
Impulse Withstand Voltage Tester
SUG255
The Impulse Withstand Voltage Tester (or High Voltage Surge Generator), it is according to IEC255-5, IEC60060, IEC60065, GB14711, GBT17215.301 and GBT17215.322. It is suitable for doing all kinds of electrical and electronic products (such as energy meter, household appliances, low voltage electrical appliances and small power motor) insulation performance test.
-
product
AC Voltage and Frequency Transducers
NMTU/F
The NMTU/F device is an AC voltage and frequency transducer with two independent analogous outputs. The A output measures AC voltage, the B output measures the frequency of input voltage. That´s why one single NMTU/F transducer is able to replace two customary transducers, thus making it possible to achieve significant savings in installation space.
-
product
TRUE RMS High Voltage DMM
8000 HVDM
Standard Electric Works Co., Ltd
● True RMS measurement● For measuring solar, PV systems● Auto ranging● Bar-graph indication● Data hold function● 3000V DC Voltage measurement● 2000V AC Voltage measurement● AC mA/uA measurement● DC mA/uA measurement● Low battery indication ● Auto power off ● Low power consumption● Rugged and compact● Comply with IEC / EN 61010-1, CAT III 1000V IEC / EN 61010-1, CAT IV 600V● Comply with CAT III 1000V for the range of 0~1000V AC/DC
-
product
PCIe 16 Bit Arbitrary Waveform Generator - up to 125 MS/s on 2 Channels, High Voltage Outputs
M2P.6571-X4
The M2p.65xx series offers different versions of arbitrary waveform generators for PCI Express with a maximum output rate of 125 MS/s. These boards allow to generate freely definable waveforms on several channels synchronously. With one of the synchronization options the setup of synchronous multi channel systems is possible as well as the combination of arbitrary waveform generator with digitizers of the M2p product family. The 512 MSample on-board memory can be used as arbitrary waveform storage or as a FIFO buffer continuously stream data via the PCIe interface. Importantly, the high-resolution 16-bit DACs deliver four times the resolution than AWGs using older 14-bit technology.
-
product
PXI High Voltage Switching Modules
These high voltage relay switching modules provides solutions for uncommitted relay, matrix and multiplexer applications that need to switch voltages up to 1000VAC. The design of these high voltage relay modules ensures they can withstand high common mode voltages and a protective safety cover is used to shield the switching components.
-
product
High Voltage Snubber Capacitor
STP-01RAN/STP-01RFN/STP-01RFB
This series of capacitors is Plastic Enclosure, Dry construction design and doesn't have leakage problem when compared with traditional Metal Enclosure Oil impregnated capacitors.Handle Medium Frequency range, high surge current, RMS current and surge voltage with temperature up to +105CCapacitance : 0.1uF - 15uF ( can be customized )Voltage range : 1,200Vdc to 17,000Vdc / 350Vrms to 6,900VrmsRMS Current - Irms : up to 100Armspeak to peak pulse current - Ipp : up to 5,900AppTemperature ranges : +85C / +105C
-
product
High Voltage 9 Pin D-Type Cables - Connector to Connector
The connector to connector cable assemblies below are not compatible with Pickering products, however, are offered for developing a connection solution for use with other products.
-
product
High Voltage Power Supplies
Trust a high voltage power supply provider with 40-plus combined years of experience. Advanced Energy’s HiTek Power and UltraVolt product lines feature hundreds of units, options, and accessories to meet your application needs.
-
product
VLF Voltage Generators
Fivestar HV Testing Equipment Co., Ltd.
VLF hipot is an AC output tester with an output frequency of 0.1 Hz or lower rather than 50/60 Hz. Although the frequency is very low, it is an alternating current with polarity reversals every half cycle.
-
product
Safety Voltage Detector ( Rechargeable Battery Type )
350 SVD
Standard Electric Works Co., Ltd
● Protection class: IP65● Bright LED visual indication● Audible indication● Non-contact voltage detection: 220Vac ~ 132kVac● Wide angle voltage detection● Frequency range: 40 ~ 70Hz ● Easy-to-prove method● Self-test function● Power source: 9V rechargeable battery ● Non-contact detection by proximity● Flashlight function● Operating temperature: 0°C~50°C● Humidity: 80% RH Max● Lightweight, robust and compact● Comply with EN 61326-1
-
product
Single Channel High Voltage Linear Amplifier
A800
The A800 is a general purpose broadband linear amplifier having a fixed amplification of 100 times and capable of bipolar high voltage output of ±400V. Any functiongenerator or arbitrary waveform generatoror any othe signal source with amplitude up to ±4 V can be used as an input device. The amplifier's output is linear from DC up to megahertz range. It can be used in a wide range of applications, for example to drive piezo actuators, MEMS, OLEDs, liquid crystals, etc.
-
product
FaithTech Ultra Low Voltage And High Current DC Load
NZ/N Series
Shenzhen FaithTech Technology Co., Ltd.
Ultra low voltage and high current DC electronic load is a high reliability and high performance electronic load product derived from FT conventional electronic load for low voltage and high current test scenarios such as fuel cell test and CPU power supply device test. For different current levels, this product includes two series: NZ and N. The voltage is 0-20V or 40V, in which the NZ series can be loaded with 0V full current, and the N series can be loaded with ultra-low voltage and full current. The load capacity is up to 0V@1200A and 0.2V@5000A . This series of products has high precision and high cost performance, which is your good choice for testing.
-
product
High Voltage Micro-SIL Reed Relays
Series 119
The Series 119 is a range of Micro-SIL Single-In-Line reed relays intended for voltages that are beyond the capabilities of conventional SIL reed relays. The 1 Form A, 1kV version is pin and package compatible with the established and popular Series 109P.
