Current Calibrators
An accurate current units of measure to facilitate comparison to and adjustment of instruments.
-
Product
Hall Effect DC Current Sensor
CYHCT-WS3
-
ChenYang Technologies GmbH & Co. KG
The sensor CYHCT-WS3 is a Hall Effect sensor for the measurement of DC current. The sensor has agalvanic isolation between the high power primary conductor and the secondary electronic circuit and withdifferent output signals and different power supplies.
-
-
Product
Snap-on RF Current Monitoring Probe
TBCP2-250
-
The TBCP2-250 is a snap-on RF current monitoring probe. The probe has a very flat response with a 3dB bandwidth of 250 MHz and is characterized over the frequency range from 30kHz to 300 MHz. Upon request, it can also be supplied with a test protocol covering the frequency range 1 kHz to 350 MHz. The aperture of the RF current monitoring probe is 32 mm. Its transfer impedance is > 12 dB Ohm in the range from 700 kHz to 300 MHz.
-
Product
Lightning Current Generator
-
Shanghai Guantu Technology Co., Ltd.
The lightning wave impulse current generator is an impulse current generator that generates a simulated lightning current waveform . Its working process is as follows: first, the transformer charges the capacitor bank through the silicon pile, when the charging voltage reaches a predetermined value, the spark gap is triggered, and the capacitor is discharged through the total inductance and total resistance of the circuit. When the resistance is greater than or equal to the critical damping value, a unidirectional impulse current wave is generated in the circuit. When the resistance is less than the critical damping value, an oscillating impulse current wave is generated. The magnitude of the impact current amplitude is related to the circuit parameters. When the capacitance value and charging voltage are the same, the smaller the inductance value, the greater the current amplitude. In order to obtain as much current as possible, a pulse capacitor with a small inductance value is usually selected, and the total length of the connecting line should be as short as possible when arranging the main capacitor, so that the total loop inductance value can be reduced as much as possible.
-
Product
Non-destructive Eddy Current Testing of Long Products such as Tubes, Rods, Wire, and Profiles
DEFECTOMAT® Product Familiy
-
Foerster Instruments, Incorporated
The DEFECTOMAT systems by FOERSTER were specially developed for quality testing and process monitoring of long products. From hot testing to all bright steel processing steps, the surfaces of semi-finished products made from austenitic, (non) ferromagnetic metals can be tested for defects. The DEFECTOMAT systems operate in a contactless and non-destructive manner in accordance with the eddy current method and are used for detecting short defects, such as holes or localized defects and transverse defects. The systems detect defective materials fully automatically and reliably. Defects can be marked, classified, and automatically discarded. the test speed of up to 150 m/s facilitates 100% testing, even at high production speeds. The systems benefit from low operating costs and frugal energy consumption as well as low maintenance costs, few wear parts, and low use of materials.
-
Product
High Speed・High Accuracy Eddy Current Type Digital Displacement Sensor
GP-X
-
Panasonic Industrial Devices Sales Company of America
The inductive displacement transducers of the GP-X Series use eddy current techniques and are particularly noted for their highly accurate measurement at a resolution of 0.02% F.S. with minimal linearity error, a high sampling frequency of 40kHz and low temperature dependence. GP-X Series Sensors are ideally suitable for the highly accurate motion and distance control of metal objects in harsh industrial environments.
-
Product
Split Type AC Current Sensor
CTF-6
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*For AC current and power measurements.*Ultra compact size and high accurate output linearity.*Easy installation in the distributing box.*Compliant with RoHS drective.
-
Product
4-in-1 OSLT Calibration Kit, DC to 70 GHz, Type-1.85 mm (f)
CK058F
-
The Network Analyzer Calibration Kits with open, short, load, and thru (OSLT) provide the RF components needed to enable stable and accurate error correct measurements. Calibration of a network analyzer using Spanawave's Network Analyzer Calibration Kits allow for precise measurements. The Calibration Kits offer broad test equipment coverage for use with the 8003 Scalar Network Analyzer as well as being compatible with most network analyzers produced by other manufacturers. Spanawave calibration kits yield complete calibrations, as it takes into consideration the three major sources of systematic error correction by one port calibration at both ports.
-
Product
150 A, 10 MHz Current Probe - AC/DC, 150 A rms, 500 A Peak Pulse, 2 meter cable
CP150B
-
Teledyne LeCroy current probes are available in a variety of models for a wide range of applications. The full range of Teledyne LeCroy current probes includes models with bandwidths up to 100 MHz, peak currents up to 700 A and sensitivities to 1 mA/div. Teledyne LeCroy current probes are often used in applications such as the design and test of switching power supplies, motor drives, electric vehicles, and uninterruptible power supplies.
-
Product
Current Recorders
-
A range of Low Cost Voltage, Current and Energy Recorders (Analysers, Analyzers) allows users to check loading and voltage performance, as well as Power and Energy surveys. A great replacement for a Hawk 5000 Meter.
-
Product
High Frequency Current Transformer Clamps
HFCT-20HD & HFCT-60HD™
-
The HFCT-20HD™ and HFCT-60HD™ are high frequency current transformer sensors designed for partial discharge detection on electric apparatus’ ground returns. Made from superior quality materials, it is designed for any environment.
-
Product
High Precision Angular Positioning, Calibration and Geometry Inspection
LabStandard DUO
-
Rotary Precision Instruments UK Ltd
Ultra precise rotary tables intended for fine inspection, metrology and test applications.2 axis design for rotary tilting applications with self-locking worm gearing and a high accuracy angular encoder ensures sensitivity and fine positioning for metrology and precision testing.
-
Product
Lamp-Based Calibration Light Sources
-
Lamp-based calibration light sources from Gamma Scientific are used for optical calibration of light measurement instruments including spectroradiometers, photometers and radiometers. All of our calibration light sources meet rigid quality standards for use in the most challenging testing environments. A wide range of light sources is available to serve as precision standards of radiant flux and white-light standards of spectral irradiance or luminance.
-
Product
MCB Tripping Current Characteristic Test Bench
-
The SCR Elektroniks 12 station MCB Tripping Characteristics Test Bench is optimally designed to verify the Tripping Characteristic of MCBs as per clause 9.10.1 of IEC 60898 (Also mentioned in Indian Standards IS 8828). The bench essentially comprises of Servo Controlled mechanism to set and maintain desired current (against incoming mains fluctuation) and a Micro controller based master controller unit plus timer, which governs the entire sequence of operation making it a stand-alone system once the user connects the MCB and configures the test parameters.
-
Product
Open Loop Current Sensor
C03 30A
-
The C03 offers efficient and precise sensor solutions for direct, alternating and pulsed currents in industrial, commercial and communication systems. It consists of three main components: an accurate, linear Hall sensor with low temperature drift, a flux collector and a transformer. It is characterized by a very low resistance and thus lowers power loss and temperature drift - for optimal performance.
-
Product
Standard Mechanical Calibration Kit, DC To 7.5 GHz, 7-16
85038A
Mechanical Calibration Kit
The Keysight 85038A calibration kit contains open circuits, short circuits and terminations with both male and female 7-16 connectors and has frequency coverage from dc to 7.5 GHz (usable to 8 GHz).
-
-
Product
Flexible AC/DC Current Tester
FCM-400
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Bending free flexible clamp sensor*Measuring ranges AC/DC 0.100A～300A(Min. resolution 0.001A)*Big CT window (φ450mm)*Easy accessibility to the hard to clamp object
-
Product
Split type AC Current Sensor
CTF-13NF
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
* Ultra compact size and high accuracy. * Easy installation in the distributing box. * Compliant with RoHS drective.
-
Product
Current Measurements of PWM or Inverter, AC/DC 0.5～5A, φ16mm
CTF-5DC
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*AC/DC 0.5～5A*Current measurements for PWM or inverter
-
Product
Current Transformer Test Set
-
Vanguard Instruments Company, Inc.
The EZCT-2000C is Vanguard’s third-generation microprocessor-based current transformer test set. Designed specifically for CT testing, the EZCT-2000C has the following outstanding features that can greatly increase productivity and save time during the commissioning stage:
-
Product
PXI/PXIe Battery Simulator Module, 4-Channel, V/I Readback, Simplified Current Sink, 750 V Isolation
43-752A-912
Battery Simulator
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 4-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
-
Product
Calibration With Traceability
-
SKF Condition Monitoring Center
SKF Quality Technology has an established global calibration network for waviness, form and vibration measurements. The QT vibration calibration system complies with the international DANAK and DPLA standards.
-
Product
Clamp type AC Current Sensor／for Power Monitor
ZCT-23
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Compact size*AC 0.1A～120A*Current measurements of terminal feeder
-
Product
AC/DC Current Digital Clamp Meters
-
Precision Mastech Enterprises Co.
Essential electrical testing tools that combine a multimeter with a current sensor, featuring jaws that clamp around a live conductor to safely measure amperage without breaking the circuit
-
Product
PXI/PXIe Wide Current Range Matrix Module, 6x4, 2-Pole, X & Y Loop-thru
40-514-002
Matrix Switch Module
The 40-514-002 (PXI) and 42-514-002 (PXIe) are low density matrices in 6x4 2-pole configuration. They are capable of switching a wide range of current, from 10 μA to 2.5 A at 220 VDC/250 VAC. The current capability of the module permits the use of a single module type for both low and medium current test applications.
-
-
Product
Electrical Test Equipment Calibrators
-
The industry leading series provides by far the fastest and safest solution for calibration of Loop, RCD, PAT's and insulation testers.
-
Product
Calibrator RTD Process Calibrator
VA720
-
Shanghai Yi Hua V&A Instrument Co., Ltd. CO.,LTD
Calibrator RTD calibrator Source and measure 7 RTD type devices ( PT10, PT50, PT100, PT200, PT500, PT1000(385), PT100(JIS)).
-
Product
Current Sensing Resistors, Metal Plate Type -MS, MB
-
Panasonic Industrial Devices Sales Company of America
An AEC-Q200 Compliant SeriesPanasonic components specified as AEC-Q200 Compliant are consistently designed into automotive systems. However, today’s Design Engineers are specifying AEC-Q200 components to meet the high-quality standards of devices beyond automotive applications.
