BoB
reroute signal paths to facilitate contact accessability.
-
Product
Fifo Serial Analyzer 2 TO 1 Breakout Boxes
FLL221/FLL221S
-
The FLL221 BreakOut Box is designed to be used with the FLL and FSA serial analyzers when they run on PC's with only one ComPort. The serial line passes through FLL221 using the 9-pin connectors. Data from both pin 2 and 3 of the serial line is available on the FLL221 output. The output cable from FLL221 is connected to the ComPort of the PC running the analyzer.
-
Product
Breakout Box
T1000-37
-
T1000-37 breakout box is our most versatile model, using dual 37 pin D-Sub connectors for signal capture or monitoring. Dual connectors provide a total of 74 test points plus a ground jack. All test points use standard size 4mm banana jacks. Test points may be connected using shorting banana cable to allow signal continuity. Ideal for continuity measurements, isolation testing, and signal capture.
-
Product
Camera Link Breakout Box
CLB-501B
-
The CLB-501B Camera Link Breakout Box provides convenient access to the data transferred between camera and frame grabber over a Camera Link connection. All video, control, and communication data can be monitored and/or sourced via a standard header connector located on the rear panel.
-
Product
Digital Interface
DNTBOB-88
-
BOB 88 is a high quality, general purpose interface to transmit and receive line level analog audio signals via a Dante network. Analog inputs are converted to digital and appear on the network as transmit channels. Audio for the analog outputs is taken from subscriptions to transmit channels on the network from other sources. When connected to a network, each break out box will appear as a separate device in the Dante Controller software interface.
-
Product
Breakout Box
-
A piece of electrical test equipment used to support integration testing, expedite maintenance, and streamline the troubleshooting process at the system, subsystem, and component-level by simplifying the access to test signals
-
Product
Measurement System for ESD Protection
SampleProtect
-
The SampleProtect measurement system is ready to go, and comes complete with Oxford Instruments’ Cryofree bottom loading cryostat – the OptistatDry BLV, Zurich Instruments’ MFLI Lock-in Amplifier, a specially designed ESD break-out box and high quality measurement grade cables. The patent-pending puck style mounting from Oxford Instruments provides safe installation of your samples. The MFLI 500 kHz Lock-in Amplifier (capable of 500 kHz demodulation as standard) with MF-MD multi-demodulator capability brings the benefits of high performance signal processing at low and medium frequencies. The differential voltage and current inputs of the MFLI are optimised for low noise operation and the high oversampling rate ensures an even better signal to noise ratio. Zurich Instruments’ unique LabOne® control software provides a toolset including an integrated oscilloscope, a spectrum analyser, a plotter and a parameter sweeper.
-
Product
NI CAN Cable, No Term, High-Speed/FD/Low-Speed, D-Sub 9-Pin F, 1m
193128-01
CAN Cable
9-Pin Female D-SUB to 9-Pin Female D-SUB CAN Cable - The DB9F-DB9F CAN Cable connects C Series CAN Interface Modules, C Series LIN Interface Modules, or C Series Multiprotocol Interface Modules to devices, breakout boxes, and accessories. It is sometimes referred to as CAN Cable (single termination or no termination). This cable is compatible with high-speed, flexible data-rate, and low-speed/fault tolerant CAN signals, available with or without termination, and in different lengths.
-
Product
Breakout Box
T1000-15
-
T1000-15 breakout box with dual 15 pin D-Sub connectors for signal capture or monitoring. Dual connectors provide a total of 30 test points plus a ground jack. All test points use standard size 4mm banana jacks. Test points may be connected using shorting banana cable to allow signal continuity. Ideal for continuity measurements, isolation testing, and signal capture.
-
Product
Breakout Box
FV-EXT
-
The handy FiberVision devices FV-EXT1 and FV-EXT2 are designed for the easy integration of FiberVision and Vision Component (VC) smart cameras into your production environment.Central interface for all supply- and communication-cables (switch board)Remote control for all VC based smart cameras such as Caminax or PictorTest of digital camera I/Os and the production environment
-
Product
OBD-II Breakout Box
PPECB
-
The Power Probe OBD-II Breakout Box is a CAN Bus circuit tester compatible with 12 and 24 Volt systems. The tool connects directly into the Vehicle’s Data Link Connector (DLC) testing for any abnormalities such as shorting and reverse polarity at the pins. If shorting or reverse polarity is present, connecting the PPECB first will prevent harm before connecting a Diagnostic Scan Tool. The Breakout Box provides a live display of present communicating signals without having to use a Digital Multimeter. Additionally, you can quickly test the voltages at all 16 pins.
-
Product
SM 1310/1550nm OTDR with VFL Blue Tooth Android
Bobcat
-
The Hand Held Bobcat OTDR has a generous 32 dB dynamic range and a short dead zone for testing FTTx fibers and networks up to the metro environment. It has an easy to read color display with fault finder, construction and expert/manual modes of operation. The OVP is shipped with Windows®/Telcordia SR-4731 compatible software that generates complete and professional documentation with the ability to include scope images and loss test results on the OTDR test reports.
-
Product
Audio Meter and Side Chaining Tool
Digital Peak Meter Pro
-
The metering capabilities of the DPMP plug-in let you control and monitor your audio signal exactly the way you want: almost every aspect of the meters can be customized. It now proposes five different scales, including Bob Katz's very popular K-System scales (K-12, K-14, K-16 and also the extra K-10). The graphs show the evolution of the audio envelopes over time, and the mid-side switch lets you verify mono compatibility problems and check the "stereoness" of your audio sources very easily.
-
Product
"Smart" Dynamic Signal Analyzers
EMX-4xxx
Signal Analyzer
The EMX-4xxx product family contains high-performance breakout boxes (EMX-4008 and EMX-4016), smart high density dynamic signal analyzers (EMX-4250 and EMX-4251), smart PXIe 625 KSA/s 4-channel digizers (EMX-4350), and charge and IEPE PXIe 625 KSA/s 4-channel digitizers (EMX-4380).
-
Product
Small, High Performance InGaAs Camera With High Image Resolution
Bobcat 640 Series
-
The Bobcat 640 cameras are offered with high frame rate of 100 Hz. The camera comes with a CameraLink or GigE Vision interface and features low weight and power.
-
Product
Small, High Performance InGaAs Camera
Bobcat 320 Series
-
The Bobcat 320 series is based on an in-house developed, temperature stabilised InGaAs detector with a 320 x 256 pixel resolution. The Bobcat 320 cameras are offered with frame rates of either 100 Hz or 400 Hz. The camera comes with a CameraLink or GigE Vision interface and features low weight and power.
-
Product
Small InGaAs Camera For Short Exposures
Bobcat Gated Series
-
The Bobcat 320 Gated series is based on an in-house developed, temperature stabilised InGaAs detector with a 320 x 256 pixel resolution. The Bobcat 320 Gated cameras are able to provide maximum frame rates up to 400 Hz. The exposure time of the sensor is configurable from 100 ns up to 1 ms in steps of 100 ns, or from 1 ms to 40 ms.
-
Product
Small, Low Cost, Uncooled InGaAs Camera
Bobcat 320 TE0 and WL Series
-
The Bobcat 320 TE0 and WL series are based on an in-house developed, uncooled InGaAs detector with a 320 x 256 pixel resolution. The Bobcat 320 TE0 and WL cameras are offered with GigE Vision interface, 400 Hz maximum frame rate and feature low weight and power.
