Fiberoptics
Field of optic fiber application.
-
product
Fiber Optic Temperature Sensor with the EasyDisk
The TPT-62
The TPT-62 fiber-optic temperature probe family employs industry standard 62.5µm core OM1 fiber optic for highly improved optical, mechanical, and reliability properties over legacy 200 µm core (1st generation) fiber optic sensors. The EasyDisk sensor tip assembly ensures IEC60076-2 (Annex E) compliant installation and enables quick insertion of the probes into the spacers within the windings of transformers.
-
product
High-Speed, Fiber-Optic Reference Transmitters
Thorlabs' Reference Transmitters are designed for high-speed fiber optic test and measurement applications. They are fully-integrated and user-configurable solutions based on proven lithium niobate (LiNbO3) modulator technology driven by high-fidelity RF amplifiers.
-
product
Photonic Electric Field Sensor System
Model No. 200-04
SRICO Model No. 200-04 Photonic Electric Field Sensor System has the ability to measure electric field with minimal disturbance to the field. The lightweight fiber-optic cables allow for easy placement of the E-field probe, allowing it to be unencumbered by the use of heavy coaxial cables that may disturb the field being measured. The dielectric E-field probe is electrically passive.
-
product
Small Aperture Fiber-Optic Probes
Small-aperture Fiber-optic Probes are best for testing closely-spaced LEDs. With an aperture of 1mm, and a diameter of 1.2mm/0.050 inches, they can test LEDs spaced as close as 0.050 inches on center. Small-aperture Fiber-optic Probes are available with straight or right-angle stainless-steel tips as shown below. This allows for precise customization to your mechanical constraints.
-
product
Fiber-Optic Measurement Technology
Fiber-optic sensors enable measurements in environments where electrical sensors reach their limits. Unlike electrical measurement methods, the purely optical measurement method is completely insensitive to environmental influences.
-
product
RGB Digital Fiberoptic Amplifier
CZ-V20 Series
SUPER HIGH POWER RGB sensor Industry's best color differentiation. High resolution amplifier for triple 16-bit calculation. New Luster Detection Sensor Head. Dual digital display & Direct access. New UV sensor head for fluorescent Detection. Three detection modes for every target [Super I / C' / C+I]
-
product
Mini Optical Power Meter
BD-POW-01
Shanghai Baudcom Communication Device Co.,Ltd.
Mini-Designed Optical Power Meter is a self-developed test instrument which is widely used for installation, operation and maintenance of fiber-optic network
-
product
T7 Fiber-Optic Cable Assembly for GPIB-140, 1000 m
182805-01K
2-Pin Male to 2-Pin Male, Core/Clad 62.5/125 um, 850 nm Wavelength Fiber-Optic Cable for GPIB-140A Extender - The GPIB T7 Cable, sometimes referred to as GPIB Cable, connects your system to high-speed GPIB-140A extender devices. You can use the GPIB T7 Cable with a GPIB extender to increase the cable length of your system up to 1 km without comprising the integrity of your GPIB system or requiring any application modifications. The GPIB T7 Cable is offered in different lengths.
-
product
OEM, Embedded, and Custom Electronics
Picosecond timingPrecision analog and mixed signal processingDigital delay and pulse generationHigh speed photonics and fiberoptic timing distributionAerospace instrumentation and simulation
-
product
S2 Blinx Digital Sensors
ULP-S2 BLINX
The Universal LightProbe S2 Blinx Digital is designed for the simple ON/OFF test of any color blinking or steady-state LED, for fast results with a digital output. The Universal LightProbe S2 Blinx Digital Sensors check the ON/OFF status of any color LED, whether stable or blinking/pulsed, up to a rate of 15 Hz, and provide a Logic “1” output (5 volts) only if the LED is “ON” and a Logic “0” if the LED is “OFF.”Operating temperature range: 0oC to 70oCPower consumption: Operates from +5, 12, 24 or 28 volts D.C., at 6mA max.Voltage protection: Withstands up to +40 volts, & reverse polarity to -18 voltsSignal Output Load: 20mA max. (Source/Sink). Non-inductiveOutput Pins: 3 gold-plated standard wire-wrap pins (0.025 in. sq.)Sensor Size: 0.560 in. dia x 1.38 in. longOperating Temperature Range: 0hC to 70hCTypical response times: <66mS, shorter for brighter LEDsFiber-Optic Probes: Wide Aperture Fiber-Optic Probe recomended
-
product
Photonics
Precision fiberoptic and free-space interfaces provide high-speed, low-jitter and low noise signal conversion, and transport of analog and digital signals.
