Filter Results By:
Products
Applications
Manufacturers
Digital Input-Output
Input/output of digital values.
-
product
Digital Input/Output Card
IOD-144
This is a 144-bit full-size card. A Programmable Peripheral Interface chip, type 8255-5 provides three 8-bit ports (A, B, and C) for each 24-bit group. Each port can be independently programmed for either input or output. Port C can also be configured as two 4-bit ports. These cards fully implement Mode 0 of the 8255 PPI chip. (Consult the factory if you desire to operate in Mode 1.) Type LS245 bi-directional transceivers sink 24 mA (optionally 64 mA) and source 15 mA. These transceiver buffers provide hysteresis correction on inputs and added drive capability on outputs. The direction of the transceivers is set by software.
-
product
Isolated Digital Input/Output Cards
PCI-IIRO-8 and PCI-IIRO-16
The PCI-IIRO-8 and PCI-IIRO-16 are low-cost, half-size cards that provide isolated input and output for PCI-Bus computers. The cards have eight or sixteen optically-isolated digital inputs for AC or DC control signals and eight or sixteen electro-mechanical relay outputs. PCI-IIRO-8 occupies four consecutive eight-bit registers in I/O space. PCI-IIRO-16 occupies eight consecutive eight-bit registers in I/O space.
-
product
256 Digital Input/Output Channels
CP387
The C387 is a single-width, 6U, CompactPCI module with up to 256 digital input/output channels. The C387 base board supports 128 channels of TTL I/O. Four mezzanine card sites can be populated with other forms of digital I/O including isolated input, isolated output, relay output, AC switch output or differential I/O. The mezzanine card concept allows multiple digital I/O types to be configured within a single module to match the application requirements.
-
product
48-Channel DIO (Digital Input/Output) PCMCIA Card
D480C
The D480C offers up to 48 separately controllable Digital I/O lines for general purpose control and monitoring applications.
-
product
Digital Input/Output and Counter/Timer Card
PCI-DIO-96C3
This is a 96 line digital input/output card with counter/timer capabilities designed for use in high I/O density application requirements. I/O connections are made via four 50-pin header connectors. The card is 12.25 inches long (312 mm) and may be installed in any full-length 5V PCI-bus (or PCI-X bus) slot in X86 type PC’s.
-
product
Low Profile Isolated Digital Input/Output Card
LPCI-IIRO-8
The LPCI-IIRO-8 is a half-size Low-Profile PCI bus compatible card that provides isolated digital input and output interface for PCI-Bus computers. The card has eight optically-isolated digital inputs for AC or DC control signals and eight electromechanical relay outputs. LPCI-IIRO-8 occupies four consecutive 8-bit registers in I/O space.
-
product
USB Digital Input/Output Module
USB-DIO-32
The USB-DIO-32 is an ideal solution for adding embedded, portable, easy-to-install digital I/O and counter capabilities to any computer with a USB port. The USB-DIO-32 is a USB 2.0 device, offering the highest speed available with the USB bus. It is fully compatible with both USB 1.1 and USB 2.0 ports. The board is plug-and-play allowing quick connect or disconnect whenever you need additional I/O on your USB port.
-
product
24 and 48 Digital Input/Output Cards
PCI-DIO Series
The PCI-DIO-48/48S, PCI-DIO-48JP/JPS, PCI-DIO-48JPL/JPLS, PCI-DIO-48H/HS and PCI-DIO-24S are 24- and 48-bit parallel digital input/output cards designed for use in PCI-Bus computers.
-
product
Isolated Digital Input/Output Card
PCI-IDIO-16
The PCI-IDIO-16 is a low-cost, 6.8" card that provides isolated input and output for PCI-bus computers. The card has sixteen optically-isolated digital inputs for AC or DC control signals and sixteen isolated FET outputs. For safety reasons in working with AC voltages, insulating shields are provided with each card.
-
product
Modbus Digital Input Output Modules
DAT3100 Series
The Datexel DAT3100 series is a range of Modbus digital input output modules. These cards or modules have the ability to accept digital voltage inputs and provide an output by the way of relays, NPN or PNP transistors. The DAT3100 devices can communicate with RS485 or RS232 on a Modbus or ASCII protocol making the DAT3100 series a very economical solution to large and small scale Data Acquisition. Combining these digital input output devices with the DAT9000 controllers and the DAT3000 analog input output modules make Datexel the smart choice where Data Acquisition is needed.
-
product
48 Channel Isolated Digital Input/Output Module
DP-VME-3078
DP-VME-3078 is a 48 Channel Isolated Digital Input Output Module. This module provides 48 input / interrupt channels and 48 digital output channels with isolation. The 48 channel inputs are divided into 12 groups, each group consisting of 4 channels and 1 common GND .The 48 output channels are divided into 6 groups, each group consisting of 8 channels and a common GND.
-
product
Digital I/O Card
PCI-DIO-120
The PCI-DIO-120, PCI-DIO-96 and PCI-DIO-72 are parallel digital input/output cards designed for use in PCI-Bus computers. The same printed circuit board is used for all three models and is populated for 120 bits, 96 bits and 72 bits respectively. The card is 12.2 inches (310 mm) long and may be installed in any 5-volt PCI slot in IBM and compatible computers.
-
product
ADC 12-bit @ 2.6 GSPS and DAC 14-bit @ 5.6 GSPS, FMC
FMC216
The FMC216 is an FPGA Mezzanine Card (FMC) per VITA 57 specification. The FMC216 utilizes AD9625 ADCs providing 12-bit conversion rates of up to 2.6 GSPS and a DAC AD9129 providing 14-bit conversion rates of up to 5.6 GSPS. The analog input/output, digital output, clock and trigger interfaces of the FMC216 are routed via SSMC connectors. The internal clock frequency is programmable and the clock is capable of locking to an external reference.
-
product
Digital Input/Output Expander (Open-Collector Outputs)
ENVIROMUX-DI16DO16
Adds 16 digital inputs and 16 digital open-collector outputs to the ENVIROMUX-2D/5D/16D. Interfaces with the ENVIROMUX-2D/5D/16D via the RJ45 Sensor Port. Digital inputs: 16 screw terminal pairs for connecting dry contact devices; One screw terminal pair for tachometer; 0 to 255 Hz. Accepts 26 to 16AWG wire. Potential free. Voltage range: 0 to +36VDC. Over-voltage surge protected. Digital outputs: 16 screw terminal pairs for open-collector outputs. Accepts 26 to 16AWG wire. Rated sink current: 500 mA per output. +5VDC, 22kΩ pull-ups. Voltage range: 0 to +24VDC. Over-voltage surge protected. Supports CAT5/5e/6 cable up to 500 ft. (152.4 m). Powered by ENVIROMUX-2D/5D/16D. Compatible with ENVIROMUX-2D/5D/16D. Dimensions WxDxH: 6.49x3.10x1.08 in (165x79x27 mm). Regulatory approvals: RoHS.
-
product
32-CH 80 MB/s High-Speed Digital I/O Card
PCIe-7300A
ADLINK PCIe-7300A is an ultra-high-speed digital I/O card. It consists of 32 digital input/output channels. High performance designs and state-of-the-art technology make this card ideal for a wide range of applications, such as high-speed data transfer, digital pattern generation and digital pattern capture applications, and logic analyzer applications. Trigger signals are available to start the data acquisition of pattern generation.
-
product
Board
Arduino Leonardo with Headers
The Arduino Leonardo is a microcontroller board based on the ATmega32u4 (datasheet). It has 20 digital input/output pins (of which 7 can be used as PWM outputs and 12 as analog inputs), a 16 MHz crystal oscillator, a micro USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get started.
-
product
Data Acquisition (DAQ)
From entry-level to high-end, data acquisition to digital input/output, ADLINK provides a diversity of modular instruments with market-leading price/performance ratio, for bigger and better measurement and automation systems. Now high-speed digitizer, switching, simultaneous data acquisition, high-density multi-function data acquisition, analog output, digital multimeter, and arbitrary waveform generator categories are all available.
-
product
USB Modular Isolated Digital Input/Output
U2600A Series
The Keysight U2600A Series U2600A Series USB Modular Isolated Digital Input/Output Devices are high performance modules that comprise of three models U2651A isolated 32-bit DI and 32-bit DO, U2652A isolated 64-bit DI and U2653A isolated 64-bit DO. The U2600A Series provides up to eight channels with 64-bit of high density opto-isolated digital input and digital output for USB 2.0 interface-based industrial applications like driving relays, actuator, or valve. The U2600A Series targets a wide range of application both in industrial automation and education.
-
product
Motion Software & Utility
The Automation Product Software SDK (APS SDK) is an all-in-one solution with an optimized uniform interface to access all supported ADLINK machine automation products. The APS SDK features rich, powerful application-oriented motion functions that co-work with components such as system platform management, field bus communications, general digital input/output, general analog input/output and support for various counters/timers. With ADLINK machine automation series products that support APS SDK, machine makers can build and deploy applications easily and quickly with a universal tool, saving on TCO and enabling faster time to market.
-
product
Digital Input/Output Expander (Normally-Open Relay Contact Outputs)
ENVIROMUX-DI16DOR16
Adds 16 digital inputs and 16 digital normally-open relay contact outputs to the ENVIROMUX-2D/5D/16D. Interfaces with the ENVIROMUX-2D/5D/16D via the RJ45 Sensor Port. Digital inputs: 16 screw terminal pairs for connecting dry contact devices; One screw terminal pair for tachometer; 0 to 255 Hz. Accepts 26 to 16AWG wire. Potential free. Voltage range: 0 to +36VDC. Over-voltage surge protected. Digital outputs: 16 screw terminal pairs for normally-open relay contact outputs. Accepts 26 to 16AWG wire. Potential free. Rated switching load: 0.5A @ 125 VAC, 1.0A @ ±30VDC. Fused. Supports CAT5/5e/6 cable up to 500 ft. (152.4 m). Includes 5V/3A power supply. Compatible with ENVIROMUX-2D/5D/16D. Dimensions WxDxH: 6.49x3.10x1.78 in (165x79x45 mm). Regulatory approvals: RoHS.
-
product
DIO-AIO Conversion Set For Conventional Power Amplifier
PAD64
PAD64 DIO(digital input/output)-AIO(analog input/output) Converter is the equipment which could be used for DI/DO (Digital input/Digital output) conversion and galvanic isolation between Real-time simulation system and protection equipment, and any other equipment which need AIO (analog binary input/ output, dry contacts).
-
product
96-CH High-Driving DIO Card
PCI-7396
The PCI-7396 is 96-bit parallel digital input/output (DIO) cards designed for industrial applications. The PCI-7396 emulates four 8255 Programmable Peripheral Interface (PPI) chips. Each PPI offers three 8-bit DIO ports which can be accessed simultaneously. The total 12/6 ports can be configured as input or output independently.
-
product
EMX-75XX
The EMX-75XX Series adds to AMETEK VTI Instruments' growing PXI Express (PXIe) Core Automated Test Equipment (ATE)TM family as a high-current, high-density digital input/output line of modules. Unlike many static I/O PXIe modules on the market today, the EMX-75XX Series can sink or source up to 300 mA on each channel. Delivering beyond just 2 V and 5 V, engineers can program the cards to support a wide range of voltages and more—on every channel, for both input and output.
-
product
Digital Input / Output Data Acquisition (DAQ) Products
In many cases, we only need to know a simple status about the device we are trying to collect data from, whether something is true or false, on or off, in one position or another. In these cases, we can determine what we need to know using a digital input, or control these things by a digital output. Digital I/O can fit into many applications.
-
product
PCI Express Card with 96 DIO and Counter/Timers
PCIe-DIO-96C3
This is a x1 lane PCIe, 96 line digital input/output card with counter/timer capabilities designed for use in high I/O density application requirements. I/O connections are made via four 50-pin header connectors. The card is 12.25 inches long (312 mm) and may be installed in any full-length slot that has x1 lane PCIe.
-
-
product
Digital Expansion Board
MSXB 013
Digital Expansion Boards. The MSXB 013 Digital Input/Output Expansion Board expands 16 digital input lines and 16 digital output lines to 64 digital input lines and 64 digital output lines.
-
product
Digital Input/Output Cards
PCI-DIO Series 24 and 48
The PCI-DIO-48/48S, PCI-DIO-48JP/JPS, PCI-DIO-48JPL/JPLS, PCI-DIO-48H/HS and PCI-DIO-24S are 24- and 48-bit parallel digital input/output cards designed for use in PCI-Bus computers. The card is 6.9 inches (175 mm) long and may be installed in any 5-volt PCI slot in IBM and compatible computers.
-
product
D10-AIO Conversion Set_for Conventional Panel-mounted Type Power Amplifier
PAD24
PAD24 DIO(digital input/output)-AIO(analog input/output) Conversion Set Conversion Set products. It could be used for DIO (Digital input/output) conversion and galvanic isolation between Real-time simulation system and protection equipment, and another equipment which need AIO (analog binary input/output, dry contacts).
-
product
Windows Driver & SDK for ADLINK USB DAQ Series Data Acquisition Modules
UD-DASK
ADLINK DASK drivers are the device drivers for custom data acquisition applications for Windows. The DASK driver libraries provide API sets for ADLINK PCI ExpressR, PCI, CompactPCI, PXI and USB data acquisition cards, to access full hardware functionalities, such as buffered/double-buffered data acquisition, pattern generation, digital input/output and etc. For novice users, the built-in CodeCreator utility helps you create your first program in just a few minutes.
