Isolated Digital Output Modules
-
Product
96 Channel Isolated Digital Input / Interrupt Output Module
DP-cPCI-3096
-
96 Channel Isolated Digital Input / Interrupt Output Module
-
Product
15-CH Isolated Digital Output Module
ND-6056
Data Acquisition Module
ADLINK's NuDAM data acquisition modules make up a total acquisition network and control system. Up to 256 NuDAM modules an be romotely controlled on any RS-485 network from a host computer, via a single serial RS-232, allowing communication from as far as 4000 feet from the host. Based on the RS-485 multi-drop network system, each module has a unique address ID, whereby simple ASCII command & response protocols through the standard RS-485 interface can control all the NuDAM modules in the RS-485 network. The NuDAM modules provide direct communications with a wide variety of sensors, perform all signal conditioning, scaling, linearization and conversion, and can acquire measurements of temperature, pressure, flow, voltage, current, and multiple digital signal types.
-
Product
160 Channel Isolated Digital Output Module
DP-cPCI-3708
-
DP-cPCI-3708 provides 160 channels of Open-collector digital outputs supporting voltage levels from 5V to 35Vdc with 200mA current sink capability. The Darlington Open-collector transistors across each drive are suited for controlling relays, switches, external digital circuitry and other similar devices.
-
Product
64-Ch Isolated Digital Output Universal PCI Card
PCI-1752U
Isolated Digital Output Card
64-ch Sink Type (NPN) Isolated Digital Output Module (PCI-1752U Only)64-ch Source Type (PNP) Isolated Digital Output Module (PCI-1752USO Only)High-voltage isolation on output channels (2,500 VDC)Wide output range (5 ~ 40 VDC)High-sink/source current on isolated output channels (200 mA max./channel)Output status readbackKeeps the output settings and values after system hot resetChannel-freeze function High-density 100-pin SCSI connector
-
Product
16-Ch Source-Type Isolated Digital Output Module With LED
ADAM-5056SO
-
Optical Isolation: 2500 VdcOver Voltage Protection: 70 VdcPower Consumption: 0.6 W (max.)16-channel
-
Product
48 Channel Isolated Digital Input/Output Module
DP-VME-3078
-
DP-VME-3078 is a 48 Channel Isolated Digital Input Output Module. This module provides 48 input / interrupt channels and 48 digital output channels with isolation. The 48 channel inputs are divided into 12 groups, each group consisting of 4 channels and 1 common GND .The 48 output channels are divided into 6 groups, each group consisting of 8 channels and a common GND.
-
Product
64 Channel Isolated Digital Input/Interrupt/Output Module
DP-VME-3636
-
DP-VME-3636 is a 64-Channel Isolated Digital Input/Interupt/Output Module. This module provides 32 channel digital input and 32 channel digital output with isolation. Channels are divided in 2 groups of 16 channels each and are routed to rear I/O. 16 non-isolated TTL channels are available.The module is used for digital interface, status setting, status monitoring, automatic test equipment, and high density industrial automation.
-
Product
PXI 64-Channel Digital Output Module
40-412A-021
Digital Output Module
The 40-412A-021 (PXI) and 42-412A-021 (PXIe) are 64-Channel Digital Output modules with high output voltage and current capability. The outputs can be used for high or low drive and each channel is capable of sourcing 0.5A from the high side or 0.5A sink on the low side. Accidental operation of both high and low side driver on the same channel is prevented by the supplied driver. Outputs are fully protected against over-voltage, over-current and thermal overload, ensuring robust and reliable operation in the toughest test environments. For high side driving, the voltage source is supplied externally, allowing the module to drive high capacity loads separate from the chassis power supply. For low side driving, the external source is not used and the module’s output operates an open collector or open drain driver.
-
Product
32-CH Sourcing Type Digital Ouput EtherCAT Module
EPS-2032
Digital Output Module
*32-CH sourcing type digital output*Quick removable European type connector*Slave module healthy monitoring*Wide operation temperature range*: -20°C - 60°CCompact size: 100 (L) x 100 (H) mm
-
Product
12DI/2Counter/2DO IoT Modbus/SNMP/MQTT Ethernet Remote I/O
ADAM-6051
Isolated Digital I/O Module
12ch digital input/2ch counter/2ch digital output(pulse output)Protocols:MQTT(TLS),SNMP,Modbus TCP,RESTful API,ASCIIGCL to perform basic logic control rulesPeer-to-Peer function to map I/O statusCloud access: Data update to AzureBuilt-in web serverWatchdog timer to recover the system
-
Product
PXI/PXIe Analog Output/Current Loop Simulator Module - 12 Channel
43-765-002
Analog Output Module
The 41/43-765-002 is a 12-channel Analog Output Module designed to meet the requirements of industrial control applications utilising current loops 4 – 20mA. It consists of up to four 16-bit, digital-to-analogue converters (DAC), capable of creating four current outputs each. Output current within 0mA - 4mA and 20mA - 24mA, give the ability to simulate error or extra signalling conditions. The ±24mA mode gives the ability to simulate either sourcing or sinking sensor.
-
Product
8-Ch Power Relay Output Module With LED
ADAM-5069
Relay Output Module
High Power Relay Output : 250Vac@5A, 30Vdc@5A8-channel Relay Output8 form A channels8 LED indicatorsJumper setting for output status when reset
-
Product
REM-11115, 4-Channel, 2-Wire Analog Output Module for Remote I/O
784749-01
Analog Output Module
4-Channel, 2-Wire Analog Output Module for Remote I/O - The REM‑11115 is an analog output module for remote I/O. Remote I/O systems are low-cost, modular systems for simple machine control and measurements. A remote I/O system consists of an EtherCAT bus coupler and individual modules mounted on a DIN rail. You control the REM‑11115 from a real-time controller, such as a CompactRIO Controller or an Industrial Controller. You can use remote I/O hardware to add low-cost I/O for simple tasks while your controller handles advanced tasks such as image processing, motion control, and high-speed or specialty measurements. You can use the REM‑11115 for voltage or current output, and it features a 2‑wire spring terminal connection method. The REM‑11115 has selectable output ranges and short-circuit-proof output channels.
-
Product
NI-9265, 4-Channel C Series Current Output Module
779334-01
Current Output Module
4-Channel C Series Current Output Module - The NI‑9265 is ideal for interfacing and controlling industrial current-driven actuators at high rates. The module has built-in open-loop detection, which generates an interrupt in software when an open loop is detected as well as zeroing … outputs to ensure safety and avoid driving actuators at system power on. The NI‑9265 requires an external power supply and includes a channel‑to‑earth ground double isolation barrier for safety and noise immunity.
-
Product
NI-9262, 1 MS/s/ch Simultaneous, ±10 V, 6-Channel C Series Voltage Output Module
785503-02
Voltage Output Module
1 MS/s/ch Simultaneous, ±10 V, 6-Channel C Series Voltage Output Module - The NI-9262 is a simultaneously updating analog output module. It features overvoltage protection, short-circuit protection, low crosstalk, fast slew rate, high relative accuracy, and NIST-traceable calibration. The NI-9262 module includes a channel-to-earth ground isolation barrier for safety and noise immunity.
-
Product
PXI/PXIe 16-Channel Digital Output Module
42-412A-024
Digital Output Module
The 40-412A-024 (PXI) and 42-412A-024 (PXIe) are 16-Channel Digital Output modules with high output voltage and current capability. The outputs can be used for high or low drive and each channel is capable of sourcing 0.5A from the high side or 0.5A sink on the low side. Accidental operation of both high and low side driver on the same channel is prevented by the supplied driver. Outputs are fully protected against over-voltage, over-current and thermal overload, ensuring robust and reliable operation in the toughest test environments. For high side driving, the voltage source is supplied externally, allowing the module to drive high capacity loads separate from the chassis power supply. For low side driving, the external source is not used and the module’s output operates an open collector or open drain driver.
-
Product
PXI/PXIe Analog Output/Current Loop Simulator Module - 8 Channel
43-765-003
Analog Output Module
The 41/43-765-003 is an 8-channel Analog Output Module designed to meet the requirements of industrial control applications utilising current loops 4 – 20mA. It consists of up to four 16-bit, digital-to-analogue converters (DAC), capable of creating four current outputs each. Output current within 0mA - 4mA and 20mA - 24mA, give the ability to simulate error or extra signalling conditions. The ±24mA mode gives the ability to simulate either sourcing or sinking sensor.
-
Product
PXI Analog Output/Current Loop Simulator Module - 4 Channel
41-765-004
Analog Output Module
The 41/43-765-004 is an 4-channel Analog Output Module designed to meet the requirements of industrial control applications utilizing current loops 4 – 20mA. It consists of up to four 16-bit, digital-to-analogue converters (DAC), capable of creating four current outputs each. Output current within 0mA - 4mA and 20mA - 24mA, give the ability to simulate error or extra signaling conditions. The ±24mA mode gives the ability to simulate either sourcing or sinking sensor.
-
Product
Digital Output
VME-2170A
Digital Output Board
The VME-2170A optically coupled digital output board consists of VMEbus compatibility logic,data control logic, four 8-bit output registers, and 32 optically isolated high-level outputs. The board is implemented as a double Eurocard form factor PC board, and provides all necessary address decoding and data transfer control logic to accept both 8- and 16-bit data transfers. Optical couplers isolate the 32 outputs from each other and from the VMEbus.
-
Product
PXIe-6738, 16-Bit, 32-Channel, 1 MS/s PXIe Analog Output Module
783800-01
Analog Output Module
16-Bit, 32-Channel, 1 MS/s PXIe Analog Output Module—The PXIe‑6738 is a high-density analog output module. The device is ideal for applications such as stimulus-response tests and open-loop simulations at high densities. You can achieve the maximum sample rate if using up to eight channels, where each channel is on a separate bank. The PXIe‑6738 also includes 10 digital I/O lines, four counter/timers, digital triggering, and advanced timing to meet a wide range of application requirements. Its digital triggering and PXI Express synchronization capabilities allow it to be coupled with additional data acquisition, motion, and vision products to create highly custom measurement solutions to test innovative designs.
-
Product
Relay Output Board
VME-2232A
Relay Output Module
VME-2232A is a 32-Channel Relay Output Board with Built-in-Test (BIT). Software compatible with the VMIVME-2232 and the VMIVME-2533.
-
Product
32-CH Discrete Output Daughter Board Module
HSL-DO32-DB-N
Digital Output Module
*Slave ID consumption: 2 - N: for 32-CH NPN sinking type outputs*Photo couple isolation voltage: 2500Vrms*Output switching capacity: Single channel 500mA; all channels 60mA at 24VDC*Output response time:ON OFF: 180µs, OFF ON: *1.2µsTerminal Base:HSL-TB64 or HSL-TB32U-DIN
-
Product
PXI Analog Output/Current Loop Simulator Module - 8 Channel
41-765-003
Analog Output Module
The 41/43-765-003 is an 8-channel Analog Output Module designed to meet the requirements of industrial control applications utilizing current loops 4 – 20mA. It consists of up to four 16-bit, digital-to-analogue converters (DAC), capable of creating four current outputs each. Output current within 0mA - 4mA and 20mA - 24mA, give the ability to simulate error or extra signaling conditions. The ±24mA mode gives the ability to simulate either sourcing or sinking sensor.
-
Product
NI-9403, 5 V/TTL, 32 Bidirectional Channels, 7 µs C Series Digital Module
779787-01
Digital Module
5 V/TTL, 32 Bidirectional Channels, 7 µs C Series Digital Module - The NI‑9403 is a configurable digital I/O interface for input or output with shift‑on‑the‑fly capabilities. Each channel features transient isolation between the I/O channels and the backplane. With reconfigurable I/O (RIO) technology (CompactRIO only), you can use the LabVIEW FPGA Module to program the NI‑9403 for applications such as custom, high-speed counter/timers; digital communication protocols; and pulse generation. In a CompactDAQ chassis, you can use the NI‑9403 only as a static (software-timed) digital I/O module. You cannot use these modules to route timing or triggering signals.
-
Product
NI-9426, 24 V, 32 Channel (Sourcing Input), 7 µs C Series Digital Module
780030-02
Digital Module
24 V, 32 Channel (Sourcing Input), 7 µs C Series Digital Module - The NI‑9426 works with industrial logic levels and signals to connect directly to a wide array of industrial switches, transducers, and devices. Each digital input line is compatible with 24 V logic levels.
-
Product
NI-9375 , 30 V, 32-Channel (Sinking Input, Sourcing Output), 7 µs (Input)/500 µs (Output) C Series Digital Module
781030-01
Digital Module
30 V, 32-Channel (Sinking Input, Sourcing Output), 7 µs (Input)/500 µs (Output) C Series Digital Module - The NI‑9375 is a digital I/O interface that works with industrial logic levels and signals for direct connection to a wide array of industrial switches, transducers, and other devices. Each digital input line is compatible with 24 V logic levels, and all the output lines are compatible with 6 V to 30 V signals, based on the external power supply. The NI‑9375 offers isolation between the input and output banks from channel‑to‑earth ground.
-
Product
8-CH 12-Bit Isolated Analog Output Cards
PCI-6308 Series
Analog Output Module
- Supports a 32-bit 5 V PCI bus- Isolated 8-CH 12-bit voltage output- 2500 VRMS optical isolation- Jumper selectable bipolar and unipolar output ranges- 4-CH isolated DI and 4-CH isolated DO- Current output version available on PCI-6308A
-
Product
PXI-6723, 13-Bit, 32-Channel, 800 kS/s PXI Analog Output Module
778998-01
Analog Output Module
13-Bit, 32-Channel, 800 kS/s PXI Analog Output Module—The PXI‑6723 delivers low-cost, high-density analog outputs to meet a wide range of applications, such as stimulus-response, signal simulation, waveform generation, and actuator stimulation. In addition, the device provides eight 5 V TTL/CMOS digital I/O lines; two 24‑bit, 20 MHz counter/timers; and digital triggering and external clocking capabilities. The PXI‑6723 can replace several kinds of instruments, including stand-alone proportional integral derivative (PID) controllers, low-speed arbitrary waveform generators, and function generators. You can control each data point for each channel to define common waveforms, such as square, sine, or sawtooth, as well as complex waveforms.
-
Product
NI-9264, 25 kS/s/ch Simultaneous, ±10 V, 16-Channel C Series Voltage Output Module
785190-01
Voltage Output Module
25 kS/s/ch Simultaneous, ±10 V, 16-Channel C Series Voltage Output Module - The NI‑9264 is a simultaneously updating analog output module that accommodates higher‑channel‑count systems. Higher density modules conserve chassis space, which leaves room for other measurement types. Each channel has its own digital‑to‑analog converter. The spring-terminal version of the NI‑9264 uses a 36‑position connector for the output channels, and each channel has a ground connection.
-
Product
4-CH Analog Output Module
ND-6024
Analog Output Module
- Channels: 4- Voltage Output: -10 V to 10 V- Output Isolation: 5000 VRMS- Resolution: 12-bit resolution- Accuracy: ± 0.02% of FSR- 7 TTL digital input
