Isolated Digital Output Cards
-
Product
PCIe 16 Bit Multi-purpose Digitizer - up to 5 MS/s on 2 Channels
M2P.5911-X4
-
The M2p.59xx series allows recording of up to eight single-ended channels or up to four differential channels both with sampling rates of up to 125 MS/s. These PCI Express cards offer outstanding A/D features both in resolution and speed. The cards can be switched between single-ended inputs with a programmable offset and true differential inputs. If used in differential mode each two inputs are connected together reducing the number of available channels by half. The 16 bit vertical resolution have four times the accuracy compared to 14 bit cards and sixteen times the accuracy if compared with a 12 bit card. All boards of the M2p.59xx series may use the whole installed on-board memory of up to 512 MSamples completely for the currently activated number of channels
-
Product
PCI-7813, 3M Gate Virtex-II FPGA, Digital Reconfigurable I/O Device
779370-01
-
The PCI‑7813 is a reconfigurable I/O (RIO) device that features a user-programmable FPGA for onboard processing and flexible I/O operation. With LabVIEW FPGA, you can individually configure the digital lines as inputs, outputs, counter/timers, PWM, encoder inputs, or specialized communication protocols. You can also program custom onboard decision making that executes with hardware-timed speed and reliability. The PCI‑7813 is well-suited for a wide variety of applications, such as high-speed waveform generation, sensor simulation, hardware-in‑the‑loop (HIL) test, custom communications protocols, bit error rate test, and other applications that require precise timing and control.
-
Product
Isolation Amplifiers
-
Knick Elektronische Messgeräte GmbH & Co. KG.
Unipolar and bipolar DC input signals 20 mV to 200 V and 0.1 mA to 100 mA calibrated range selection. Working voltage up to 1000 V AC / DC.
-
Product
32Ch Isolated Output Card
SET-1320
-
This card offers 32 optically separated open collector outputs that can switch up to 100mA at 60V. SET-1320 combines tight IO with high isolation voltages and an extensive output voltage range.
-
Product
32-CH Sinking Type Digital Input EtherCAT Module
EPS-1132
-
*32-CH sinking type digital input*Quick removable European type connector*Slave module healthy monitoring*Wide operation temperature range: -20°C - 60°C*Compact size: 100 (L) x 100 (H) mm
-
Product
Isolation Amplifiers
-
Isolation Amplifiers provide power supply designers with a higher performing, single chip alternative to isolation techniques based on optocouplers and shunt regulators. Analog Devices ADuM3190 and ADuM4190 isolated error amplifiers have a 400 kHz bandwidth, with 0.5% typical initial accuracy at 25°C and 1% total accuracy over the extended temperature range of –40˚C to +125˚C. This provides manufacturers of ac-to-dc and dc-to-dc power supplies with a significant upgrade in speed and operating temperature range, as well as a 5× improvement in transient response.
-
Product
12-Bit, 4-Ch Analog Output PCI Card With 16-Ch Digital I/O
PCI-1721
-
10 MHz maximum digital update rateSynchronized output function16-ch DI/O and one 10 MHz 16-bit resolution counterFour analog output channels with 1,024 samples FIFO bufferA 12-bit DAC is equipped for each of analog output channelsReal-time waveform output function with internal/external pacerFlexible output types and range settingsKeeps the output settings and values after system hot resetAuto calibration functionBoardID™ switch
-
Product
32-CH Isolated DIO Card
LPCIe-7230
-
ADLINK LPCIe-7230 is 32-CH isolated input and/or card. It provides a 2,500 C optical isolation protection. Two wide input range of the LPCIe-7230 makes it easy to sense the status of external devices. The non-polarity characteristic is suitable for a wide variety of industry applications. The LPCIe-7230 devices also feature a wide output range from 5 to 35 V, which is suitable for relay driving and industrial automations applications. The LPCIe-7230 also provides two interrupt sources on digital input channels, which are easily user configurable.
-
Product
PCI Bus Analog Output Board, 4 Isolated Outputs, 14 Bit
APCI-3501-4
-
4 analog output channels Optical isolation 500 V Settling time 30 µs typ. 14-bit resolution (13 bit for 0-10 V) Output voltage: ±10 V, 0-10 V (switchable through software) Output voltage after reset: 0 V Each output channel has its own ground line (without optical isolation from the others) Driver capacity: 5 mA/500 pF Short-circuit protection, EMI filters Noise neutralization of the PC supply Creeping distance: 3.2 mm acc. to DIN VDE 0411-100 Watchdog for resetting the analog output channels (4 different time units: µs, ms, s, min) or as 12-bit timer (with interrupt possibility), when the watchdog function is not necessary2 digital input channels, 24 V, isolated 2 digital output channels, 24 V, isolated Noise immunity Test level: ESD: 4 kV Fields: 10 V/m Burst: 4 kV Cond. radio interferences: 10 V
-
Product
Ethernet/LXI hybridNETBOX 14 Bit Digitizer and 16 Bit AWG - 500 MS/s Digitizer on 4 Channels, 625 GS/s AWG on 4 Channels
DN2.825-04
-
The hybridNETBOX DN2.82x series internally consists of a Digitizer and an AWG that can run together or independently. That allows simultaneous data generation and data acquisition for stimulus-response tests, ATE applications, MIMO applications or closed-loop applications. Used independently, the digitizer can acquire test data in the field and the AWG can replay this test data in lab. The hybridNETBOX offers 14/16 bit resolution and is available with digitizer sampling rates of up to 500 MS/s and AWG sampling rates of up to 1.25 GS/s. The hybridNETBOX can be installed anywhere in the company LAN and can be remotely controlled from a host PC.
-
Product
32-CH 12-Bit 100 kS/s Isolated Analog Input Card
PCI-9113A
-
ADLINK PCI-9113A is a 32-CH, 12-bit, 100 kS/s isolated analog input card. The PCI-9113A provides analog inputs with 3 programmable input ranges for both bipolar and unipolar inputs. The 32-CH single-ended analog inputs can be converted to 16-CH differential analog inputs, which improve the noise rejection in harsh industrial environments. The analog inputs are isolated from the PC's system ground. This feature not only protects the PC from being damaged from surges on the signal lines, but also eliminates ground loops and common-mode problems commonly seen in industrial measurement applications. The PCI-9113A provides custom circuit area for input signal conditioning. Either signal attenuation or filtering can be applied on per channel basis. With all the features, ADLINK PCI-9113A delivers cost-effective and reliable data acquisition capabilities for ATE, sensor monitoring, data logging, power transmission, and a broad variety of industrial measurement applications.
-
Product
DisplayPort To DVI Adapter For Embedded Controllers
Y1261A
-
Achieve backward compatibility between DisplayPort and a DVI computer monitor.
-
Product
NI-6584, 16 Mbit/s, 16-Channel Digital I/O Adapter Module for FlexRIO
781290-01
-
16 Mbit/s, 16-Channel Digital I/O Adapter Module for FlexRIO—The NI-6584 is a digital I/O adapter module that, when combined with a PXI FPGA Module for FlexRIO or the Controller for FlexRIO, creates a digital instrument for interfacing with 16 RX and TX pairs of RS485 or RS422. This digital I/O adapter
-
Product
High Density SPDT Plug-In Switch Card
1260-116
-
The Astronics 1260-116 is a 24-channel, Form C, single-pole double-throw (SPDT) switch card for use in either the 1260-100 VXI Carrier or the 1256 GPIB/RS-232 Switching Mainframe.
-
Product
Value DSP-Based 4-Axis Motion Control Universal PCI Card
PCI-1245V
-
Encoder input is 10 MHz for 4xAB mode, 2.5 MHz for CW/CCW modePulse output up to 5 MppsSupports linear and circular interpolationHardware emergency inputSupports E-GearSupports programmable acceleration/deceleration rateMemory buffer (10K points) for trajectory planning which is designed in DSP(Auto-blending is not supported)Position compares triggering up to 100 KHz, and memory buffer is up to 100 K points in DSPPosition latchProgrammable interrupt and watchdog timerRDY/LTC-dedicated input channels & SVON/CMP/CAM-DO/ERC-dedicatedoutput channels are switchable for general input and output purposes
-
Product
PXI Analog Output Module
-
PXI Analog Output Modules support both static and software-timed voltage output applications. Modules also include 5 V TTL/CMOS digital I/O lines. Some PXI Analog Output Modules can deliver simultaneous, multichannel updates for control and waveform output applications, such as stimulus-response, power supply control, high-speed, deterministic control, and sensor/signal simulation. These advanced features enable you to use the PXI Analog Output Module to replace several kinds of instruments, including stand-alone proportional integral derivative (PID) controllers, low-speed arbitrary waveform generators, and function generators.
-
Product
Ethernet/LXI digitizerNETBOX 16 Bit Multi-purpose Digitizer - 40 MS/s on 40 Channels
DN6.593-40
-
The digitizerNETBOX DN6.59x series allows recording of up to 48 synchronous channels with sampling rates of 20 MS/s up to 125 MS/s. These products offer outstanding A/D features both in resolution and speed as a remote instrument. The powerful A/D amplifier section offers 6 different input ranges, programmable offset and a software switching from single-ended (full number of input channels) to true differential (half number of input channels).
-
Product
Dual-Port Isolated RS-422/485 Communications and Watchdog Card
WDG-2S
-
This multifunction card contains a watchdog timer, two RS422/485 serial communications ports, and an internal temperature monitor and computer voltage monitor. This is a full-length card that installs in "long" expansion slots of IBM PC/XT/AT and compatible computers. The following paragraphs describe functions provided.
-
Product
64-Ch Isolated Digital I/O PCIE Card
PCIE-1756
-
Wide output range (5 ~ 40 VDC)High sink current on isolated output channels (500mA max./ch)Wide input range (10 ~ 30 VDC)High-voltage isolation (2,500 VDC)Interrupt handling capability2,000 VDC ESD protectionEither +/- voltage input for DI by groupHigh over-voltage protection (70 VDC)Output status read-backKeeps the output settings and values after system hot resetChannel-freeze function
-
Product
Handheld Digital Multimeter, 4 digit, with IP 67
U1241C
-
The strong and solid U1240C Series handheld digital multimeters (DMMs)are the tools technicians or industrial test engineers use to perform their work confidently and efficiently. Designed for handheld users working in various environments, the U1240C series is certified to IP 67 and capable to withstand up to 3-meter (10 feet) drop to suit harsh working environments. The U1240C handheld DMMscan even work longer for you with up to 400 hours of battery life. With the built-in LED flashlight, the U1240Chandheld DMMsallow users to single-handedly illuminate test area.
-
Product
20W to 30W - Single Output / Multiple Output
PXE Series
-
*Industry Standard 2" x 1.6" Footprint*9-18, 9-36, 18-36, 18-75, 36-75 Vdc Inputs*3.3, 5, 12, 15, ±5, ±12, ±15 Vdc Outputs*1600 Vdc Isolation*-40 to 100 °C Case Temperature*Six-sided Shielding*EN61000-4 Immunity
-
Product
Digital Signal Processor Card
CHAMP-AV8
-
Curtiss-Wright Defense Solutions
The CHAMP-AV8 6U OpenVPX digital signal processor (DSP) combines the floating-point performance of the 3rd generation Intel Core i7 processors with the substantial bandwidth and system-enabling features of the 6U OpenVPX form factor. Utilizing a pair of 2.1 GHz quad-core processors featuring the Advanced Vector Extensions (AVX) instruction set, the CHAMP-AV8 DSP card delivers up to 269 GFLOPs.
-
Product
8-Ch Source-Type Digital Output EtherCAT Slice IO Module
AMAX-5056SO
-
Channels: 8 (Source Type)Voltage Rating: 10~30VDCRated Current Output: 0.5A per channel at signal "1"Leakage Current: 10 μA per channel at signal "0"Output Delay: From logic level 0 to 1: 150μs; From logic level 1 to 0: 2ms
-
Product
4-Port RS-422/485 Isolated Serial Communications Card
cPCI-3544
-
- 32-bit CompactPCI®, PICMG® 2.0 Rev 2.1- Plug-and-play, IRQ & I/O address automatically assigned by PCI BIOS- Four asynchronous communications ports with intelligent buffer- Four RS-422/485 ports- 2500 VRMS isolation voltage
-
Product
16 Relay Output PCIe Board, 8 Isolated Digital Input Channels, 24V
APCIE-2200-16-8
-
8 electromechanical relays with change-over contacts The PCI-Express 16 relay board APCIe-2200-16-8 has 16 relay output channels and 8 isolated digital inputs, 24 V. 7 inputs are interruptible. The board is especially suited for applications like industrial I/O control, signal switching, alarm monitoring, as interface to machines, for the ON/OFF monitoring of motors, lights etc. in the harsh industrial environment.
-
Product
32Ch Isolated Input Card
SET-1310
-
This card provides 32 optically isolated digital inputs. SET-1310 combines high-density IO with high isolation voltages and a wide input voltage range. It allows to break ground loops and protect your system from high-voltage spikes, but also to connect high voltage signals to standard logic level acquisition devices. The channel-to-channel isolation allows to connect signals from different DUTs to a single acquisition system without compromises.
-
Product
Synchro to Digital-Resolver to Digital Converters
SDC-RDC 20
-
Computer Conversions Corporation
SDC & RDC 20 BIT Synchro / Resolver to Digital Converter
-
Product
Embedded MXM GPU Module with NVIDIA® Quadro® Embedded RTX5000
EGX-MXM-RTX5000
-
The EGX-MXM-RTX5000 module features advanced NVIDIA® Turing™ GPU technology in MXM 3.1 Type B+ form factor. It’s compact, slim and reliable design makes it suitable for mission critical environment. EGX-MXM-RTX5000 supports 4 DP 1.4b displays offering a flexible and easy solution for medical and gaming applications.
-
Product
16-bit, 100KHz, 8SE/4DIFF A/D Inputs; 4 14-bit, 30KHz D/A Outputs, 4 24V Digital I/O, all isolated
CPCI-3120-8-4
-
Input range:- ± 10 V, 0-10 V software programmable- 0-5 V, ± 5 V, 0-2 V, ± 2 V, 0-1 V,- ± 1 V (gain)- 0-20 mA (option)- software-programmable amplifier:- PGA x1, x2, x5, x10- Conversion triggered through software,scan, timer, external event- Onboard FIFO buffering for 256 analog values- Data exchange through 16-bit I/O or 32-bit memory (PCI DMA)- Sequence RAM- Overvoltage protection- input filter: 160 kHz
-
Product
16 Channel Isolated Analog Output Module
DP-cPCI-2502
-
The DP-cPCI-2502 is a 16 channel analog output module organized in four groups of 4 channels each. Each group is isolated with respect to each other and with respect to the system using optical isolators and DC-DC converters. Each output channel is driven by a 16 bit resolution precision DAC. The input digital data is converted to analog signals of ±10V range. The digital data for the DACs is written from the cPCI interface via two banks of latches enabling a double buffered output scheme.
