Voltage Calibrators
An accurate voltage units of measure to facilitate comparison to and adjustment of instruments.
See Also: Voltage Sensors
-
Product
PXI High Voltage Programmable Resistor Module, D-Type Connector
40-230-150-HI
Programmable Resistor Module
The 40-230-150-HI (PXI) and 42-230-150-HI (PXIe) are programmable resistor modules with 1 channel which can be set between 4.5Ω and 1.5MΩ with 0.125Ω resolution with maximum voltage of 1kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
PXI High Voltage Programmable Resistor Module, Connector
40-230-323-HI
Programmable Resistor Module
The 40-230-323-HI (PXI) and 42-230-323-HI (PXIe) are programmable resistor modules with 2 channels which can be set between 3Ω and 3.55kΩ with 1Ω resolution with maximum voltage of 1.2kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
VisualDetect LCD Voltage Detector / Interface Tester
VDL-01AB
-
Hachmann Innovative Elektronik
VisualDetect LCD is an easily operated voltage detector and interface-tester. Its automatic, thorough self-test ensures reliable function. The permanently enabled interface-tester warns against defect interfaces. Additionally the LC-display indicates the measured current [I/A] and frequency [f/Hz]. Thanks to the integrated configuration menu it can be adjusted to switchgears operated below nominal voltage on-site.
-
Product
Solid State Voltage Injector
J2110A
-
While it is possible to obtain high quality injection transformers with bandwidths as wide as 1Hz to 5MHz or more, in some cases this is still insufficient for some tests. For example a typical heater control loop might have a bandwidth of less than 1Hz while some linear regulators and opamp circuits can have bandwidths of up to 100MHz or in some cases even higher. For these applications, a solid state injector can provide the necessary bandwidth. A solid state injector can perform at DC, while the upper frequency limit is dictated by the components selected and the printed circuit board material and layout. It is possible to obtain a solid state injector with a working range of DC – 200MHz, though above 50MHz the interconnection between the injector and the circuit being tested can become quite critical. It is essential that ripple from the injector power supply does not dramatically degrade the dynamic range or the signal to noise ratio of the measurement. The resulting plots are often much cleaner when using a solid state injector than with a transformer injector.
-
Product
Electronic Calibration Module (ECal), 50 GHz, 2.4 Mm, 2-port
N4693D
-
The Keysight N4693D microwave electronic calibration (ECal) module makes calibration of Keysight vector network analyzers fast, easy, and accurate. The N4693D is a precision 2-port ECal module that supports 2.4 mm connectors up to 50 GHz. Select either female-female, male-male, or female-male connectors. The plastic storage case for the N4693D is included for securing your ECal module and accessories.
-
Product
Voltage Control Attenuator
-
RF Lambda’s voltage control attenuators allow for precision control of RF signals. With a voltage variable control pin the signal can be fine-tuned as needed by the system. These attenuators offer fast response time and wide band operation. Hermetically sealed options are available upon request.
-
Product
High Voltage Dry Reed Relays For up to 15 kV
SERIES 62 & 63
-
ungsten switches with power rating of 50 Watts maximum? Three switch types:5kV stand-off, 3.5kV switching10kV stand-off, 7.5kV switching15kV stand-off, 12.5kV switching? Series 62 has push-on connectors on top face for EHT and solder pins and nylon studs on the underside for PCB mounting
-
Product
Standard Voltage 37 Pin D-Type Connectors
-
The connectors below are not compatible with Pickering products, however, are offered for developing a connection solution for use with other products.
-
Product
High Voltage DC Power Supply
IT6700H Series
-
IT6700H series high-voltage DC power supplies is with maximum output power 3000W, adjustable voltage 0-1200V and current 0-10A, IT6700H series have desktop and shelves installation function, easy to operate. IT6700H series provide list mode, built-in RS232 / USB / GPIB communication interface, rich SCPI instructions facilitate the formation of a variety of intelligent test platforms.
-
Product
Clamping Voltage Tester
MIG0603CLV1
-
The MIG0603CLV1 is a generator for testing varistors. It has circuits with three different source impedances and up to 11 different measurement ranges. The instrument is used to perform varistor clamping voltage tests on up to 1000 V varistor types. The test impulse is a 8/20µs current waveform up to 200A which is maintained over the entire load range.
-
Product
FaithTech Ultra Low Voltage And High Current DC Load
NZ/N Series
-
Shenzhen FaithTech Technology Co., Ltd.
Ultra low voltage and high current DC electronic load is a high reliability and high performance electronic load product derived from FT conventional electronic load for low voltage and high current test scenarios such as fuel cell test and CPU power supply device test. For different current levels, this product includes two series: NZ and N. The voltage is 0-20V or 40V, in which the NZ series can be loaded with 0V full current, and the N series can be loaded with ultra-low voltage and full current. The load capacity is up to 0V@1200A and 0.2V@5000A . This series of products has high precision and high cost performance, which is your good choice for testing.
-
Product
PXI High Voltage Power Multiplexer, Single 24:1
40-331A-001
Multiplexer Module
The 40-331A-001 single 24:1 MUX is part of our range of 40-331A/332 High Voltage Power Multiplexer and Matrix Modules and is suitable for applications requiring high voltage power relay switching with high density. They feature current handling up to 5A, 1000VDC/1000VAC peak cold switching and 110VDC/250VAC hot switching.
-
Product
PXIe High Voltage Programmable Resistor Module, D-Type Connector
42-230-035-HI
Programmable Resistor Module
The 40-230-035-HI (PXI) and 42-230-035-HI (PXIe) are programmable resistor modules with 2 channels which can be set between 3.5Ω and 201kΩ with 4Ω resolution with maximum voltage of 1kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
Conformance Calibration Standard Test Card for GS1-DataBar Symbol Verifiers
AI-CCS-DATABAR
-
This test card is ideal for testing verifiers, scanners, and other GS1-DataBar barcode reading equipment. It also can serve as an excellent training aid to ensure new operators are using the proper methodology and are proven competent in the use of verifiers.
-
Product
PXIe High Voltage Programmable Resistor Module, REDEL Connector
42-230-344-HI
Programmable Resistor Module
The 40-230-344-HI (PXI) and 42-230-344-HI (PXIe) are programmable resistor modules with 1 channel which can be set between 4Ω and 1.5MΩ with 2Ω resolution with maximum voltage of 1.2kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
Voltage Voltmeter
Voltstik
-
The Voltstik is a distribution voltage voltmeter designed for use on lines and in substations. This meter is employed onto a line by using a hot stick and universal chuck adapter. It is capable of measuring voltage phase to phase, and phase to ground. This high impedance instrument is an excellent choice for solving multiple problems associated with operating a medium voltage system. Its key applications are defined under three groups, safety confirmation of the voltage present, troubleshooting voltage problems, and phasing.
-
Product
High Collector To Emitter Voltage
-
High collector-to-emitter voltage photocouplers (optocouplers) are optically coupled isolators containing a GaAs infrared light emitting diode and an NPN silicon Darlington connected phototransistor. The isolation voltage during input and output and the voltage between the collector and the emitter of the transistor are both high.
-
Product
PXIe High Voltage Programmable Resistor Module, D-Type Connector
42-230-045-HI
Programmable Resistor Module
The 40-230-045-HI (PXI) and 42-230-045-HI (PXIe) are programmable resistor modules with 2 channels which can be set between 4Ω and 2.954MΩ with 4Ω resolution with maximum voltage of 1kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
Dual Channel High Voltage Linear Amplifier
A800D
-
This unit contains two independent A800 amplifiers that share common ground reference and power supply.
-
Product
High Voltage Probe
HVP-40
-
*MAX. Voltage : DC : 40KV, AC : 28KV, (50/60Hz only) CAT II.*1000MΩ Input Impedance.*Accuracy **DC: ± 1% to 20KV. ± 2% to 40KV. **AC: -5% to -10% (50/60Hz)*Division Ration : 1000:1*CE, TUV GS, UL, CUL, IEC1010
-
-
Product
Ice Point Calibrators
-
These ice point calibrators are designed to accurately calibrate probes at the freezing point of water. These devices have multiple thermowells to calibrate multiple sensors simultaneously.
-
Product
Calibration Devices For Spring Impact Hammer
CX-TF06A
-
Shenzhen Chuangxin Instruments Co., Ltd.
Calibration Devices for Spring Impact Hammer
-
Product
PXI Voltage Amplifier 10K Ohm, SMB
41-650-012
Amplifier
The 41-650 is a 5 channel voltage amplifier ideal for increasing the output voltage from other PXI modules, enabling users to easily generate the signal voltages commonly required in applications such as automotive test. Each amplifier can be independently programmed to a gain of 1, 2, 5, 10 or 20, enabling it to be used with modules with low output voltage capability. Inputs and outputs can be provided either on SMB connectors or on a D Type connector to suite the user’s wiring system.
-
Product
High Voltage Amplifier
HA-805
-
*800Vp-p(±400V DC) *200mAp-p(±100mA DC) *Bandwidth: ≦300KHz(400Vp-p) *Slew Rate: 300V/us *Gain(AMPL):0~180(10 Turn VR) *DC Offset: ≦0~±400V(10 Turn VR+SW) *Output Resistor: 100Ω *Microprocess Control Protection
-
Product
Accredited Humidity Calibration Services
-
Thunder Scientific's calibration laboratory is accredited by NVLAP (National Voluntary Laboratory Accreditation Program), Certificate of Accreditation No. 200582-0 to ISO/IEC 17025 and ANSI/NCSL Z540-1 1994.
-
Product
4-in-1 OSLT Calibration Kit, DC to 40 GHz, 2.92 mm (m)
CK562A
-
The Network Analyzer Calibration Kits with open, short, load, and thru (OSLT) provide the RF components needed to enable stable and accurate error correct measurements. Calibration of a network analyzer using Spanawave's Network Analyzer Calibration Kits allow for precise measurements. The Calibration Kits offer broad test equipment coverage for use with the 8003 Scalar Network Analyzer as well as being compatible with most network analyzers produced by other manufacturers. Spanawave calibration kits yield complete calibrations, as it takes into consideration the three major sources of systematic error correction by one port calibration at both ports.
-
Product
PXIe High Voltage Programmable Resistor Module, D-Type Connector
42-230-144-HI
Programmable Resistor Module
The 40-230-144-HI (PXI) and 42-230-144-HI (PXIe) are programmable resistor modules with 1 channel which can be set between 4Ω and 1.5MΩ with 2Ω resolution with maximum voltage of 1kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
Insulation Tester Calibrator
M191
-
High resistance calibrator for insulation testers up to 10 kV. Other insulation related functions include HV capacitance, short current, dielectric and polarization parameters and timer test.
-
Product
Gage Calibration Services
-
Accu-Chek calibrates all inspection, measuring, and test equipment (IMTE) to either manufacturer’s specifications, Federal/Military/ANSI specifications or, if requested, we can perform calibrations to customer requirements. We calibrate all IMTE using written procedures and standardized data sheets.
