Inspection Services
See Also: Inspection, Inspection Systems
-
Product
Services
-
Application & retrofit, start up, training/tech support, and more from TLP Solutions
-
Product
Services
ADC Channel Listening
-
The program is used for listening to signals coming to the input channels of ADC modules and FFT Spectrum Analyzers.
-
Product
Automated Surface Inspection for Glossy Components
-
Flawlessly glossy surfaces are among the most important quality features of many premium products. The smallest surface defects immediately have a degrading effect on the product. The result: disappointed end customers or buyers. At the same time, reflective surfaces are often very sensitive and a challenge for optical metrology. A manual inspection is tedious, expensive, and ultimately always governed by subjective decision criteria. During production, faulty painting or coating processes can cause high scrap rates. Defects that are not detected even during the final inspection can lead to expensive complaints and, in the worst case, to the loss of the customer. Only an efficient, automated surface inspection achieves the highest quality at acceptable costs.
-
Product
Pipe & Duct Inspection Cameras
-
Pipe & Duct Inspection Camera are video inspection cameras with a probe long enough (roughly 70 ft.) to locate and identify an obstruction in a water or sewer line or HVAC duct by taking close-up video clips and photos of it. The P16PIP probe (also available separately) that comes with the DPS16 Pipe & Duct Inspection Camera has better camera lighting and optics and slightly better resistance to water than the P610-20PR probe that attaches to a recording or non-recording wet/dry inspection camera console.
-
Product
Calibration Services
-
SIMCO provides calibration services to over 3,000 organizations including the top 10 U.S. biomedical manufacturers and 9 of the top 10 U.S. aerospace and defense manufacturers. A calibration industry leader since 1962, SIMCO has received calibration leadership awards for 8 consecutive years from independent research firm Frost & Sullivan. SIMCO has earned these awards and developed a strong reputation for being “the standard for quality service” by providing customers with the advantages listed below.
-
Product
The Complete Solution for Optical Surface Quality Inspection
OptiLux SD (Scratch-Dig)
-
RedLux’s OptiLux SD system provides the complete solution for control of optical surface quality (scratch-dig) by offering a breakthrough in measurement performance along with conformity to industry standards. Designed with flexibility in mind and further enhanced by a range of customer inspired features, the OptiLux SD can support the most demanding of optical surface quality inspection processes, from highly customized optical components in low volume, to standard components in high volume.
-
Product
Design for Test Service
-
Design For Test (DFT) is a technique used to implement certain testability features into a product. Testing House can provide an analysis of the CAD data for testability of your circuit board. Access to a board can be very difficult as boards get smaller and designs get more densely populated. We can work with your design engineer to improve testability and maintain an effective in-circuit test. When access to the board is limited and boundary scan devices are present, we can provide the customer a list of key nodes that will require access in order to provide a very effective test. Our analysis will provide a list of all the accessible test points and an explanation for any nodes declared inaccessible.
-
Product
Defect Inspection Systems
-
Candela® defect inspection systems detect and classify a wide range of critical defects on compound semiconductor substrates (GaN, GaAs, InP, sapphire, SiC, etc.) and hard disk drives, with high sensitivity at production throughputs.
-
Product
Mobile Design & Manufacturing Service
-
Advantech's extensive technology design experience offers tailor-made tablet solutions optimized for different vertical markets.
-
Product
Technical Service
-
Atlas Material Testing Solutions
Proper maintenance and calibration are critical to maximize the reliability of your test data. A poorly maintained instrument can produce results that diminish the repeatability and reproducibility of the data and an instruments downtime can delay your product's time to market. Atlas is committed to helping you acquire the most accurate data possible through our Technical Services support.
-
Product
Fiber Optic Inspection Microscope
80761
-
The Miller 400x Microscope helps inspect fiber optic connectors quickly and easily. Its ergonomic design and built-in features make it ideal for field and lab use. The microscope features a pressure-activated on/off switch, focusing wheel, eyepiece, auxiliary white LED light source rated for 100,000 hours, adapter tip for inserting ferrule and battery compartment. Includes 2.5mm universal adapter cap and zipper case.
-
Product
Automatic Flight Inspection System
AT-920DG
-
Airfield Technology is pleased to announce the availability ofa new product, the AT-920DG Automatic Flight InspectionSystem.The new AT-920DG system combines the unique groundbasedinspection capability of our original AT-920 with theproven DGPS positioning system and WinFIS flight inspectionsoftware from our larger, dual equipment AT-930DG system.
-
Product
Vison Inspection System
-
High Speed stroboscopic 2D vision inspection system for die attached and wirebond quality in back-end semiconductor processes. User friendly HMI for easy recipe creation and management. Able to configure with various defect identification module. (Strip Mapping, Inker, Scriber, Pucher, Bristle, Laser wire cutter and Laser clip bonding cutter.)
-
Product
Ceramics and Glass Inspection Systems
-
Due to their special material properties, ceramic and glass components are the basis of many high-tech products. The same properties make the production complex and costly. Substrate defects that lead to failure of finished components should be avoided at all costs. For this reason, early automated optical inspection is essential.For the inspection of sapphire and quartz glass Intego has developed systems to detect both external and internal defects and can also provide cutting suggestions. Using index matching it is possible to test rough or uneven glass profiles.For the inspection of ceramic components Intego offers solutions specifically tailored to the respective testing task. Our modular design uses standard components that have already been developed and tested and in most cases only requires minimal adaptation.
-
Product
Inspects MEMS and Wafer Level Devices
NorCom 2020-WL
-
The NorCom 2020-WL is specifically designed for wafer-level inspection and leak tests up to 1000 devices per cycle. The system can inspect up to an 8” wafer on or off a saw frame. It is designed to test MEMS and other wafer level devices that have a cavity.
-
Product
Sound Level Meter for Automotive – Car Noise Emission Inspection
HD2010MCTC
-
The level of noise produced by vehicles shall comply with standards prescribed by international regulations. During car inspections, horns and exhaust devices must be in good condition and comply with the requirements.
-
Product
Services
-
Direct and through our trained distributor network, Protea offers On-Site System Service for our fixed installations and At Factory Service for our transportable analysers.
-
Product
Weathering Test Services
-
Atlas Material Testing Solutions
The climates of southern Florida and central Arizona are recognized as global benchmarks for natural weathering environments. The warm, humid, subtropical environment of our outdoor test sites in Miami and the intense sun and arid climate of our site in Phoenix are some of the harshest climates to which your products can be exposed. Often the best natural weathering test scenario requires testing in a variety of climates. For that reason, Atlas offers the world’s largest network of outdoor weathering test facilities with more than 20 sites worldwide.
-
Product
Thickness and Flaw Inspection
OmniScan MX ECA/ECT
-
With thousands of units being used throughout the world, the OmniScan® MX is a field-proven, reliable instrument that is built to withstand harsh and demanding inspection conditions. Compact and lightweight, its two Li-ion batteries provide up to 6 hours of manual or semi-automated inspection time.
-
Product
Wafer Inspection Machine
IV-W2000
-
The IV-W2000 is a wafer inspection machine that features on-the-fly scanning and inspection as well as automatic handling of 6/8/12-inch wafers. With the option to have a Chinese language UI, this machine is also known for being intuitive and user-friendly.
-
Product
Industrial CT X-Ray Inspection System
X5000
-
The X5000 is the most versatile system offered by North Star Imaging. The system boasts a large scanning envelope and excellent ergonomics for loading sizable objects while still maintaining the sensitivity to inspect even the smallest of items.
-
Product
Automatic Double-Sided Bare PCB Final Inspection AVI System
FI-18 Series
-
InScan Limited (SIP) Co., Ltd.
InScan FI-18 is a compact and high performance fully automatic double sided AVI system for Final Inspection of PCB boards.The setup is based on golden board and CAD data which greatly simplifies the setup process. The FI-18 series inspects and processes a double sided board sized 210X300 mm 5.5 sec. Superior interline high resolution CCD sensor.
-
Product
Semiconductor Wafer Microscope Inspection System
MicroINSPECT
-
MicroINSPECT Semiconductor Wafer Defect Microscope Inspection System combines state-of-the-art robotics, intelligent microscopes and SITEview software to provide a flexible, easy-to-operate defect inspection platform for either micro or macro defect wafer inspection.
-
Product
GoPxL Inspection Software
-
GoPxL® is our next generation software application for creating end-to-end, web-based inline measurement and inspection solutions deployed on Gocator® 3D Smart Sensors and Gocator® 2D Smart Cameras.
-
Product
TPMS Service
-
To warn you that at least one or more tires are significantly under-inflated, possibly creating unsafe driving conditions.
-
Product
Motor Vehicle Inspect Lines Engineer Program
-
Foshan Analytical Instrument Co, Ltd.
It is suitable for measurement of motor vehicles equipped ignition engine with max total mass more than 3500kg.Including the dual idle speed method test.Meet the requirement of GB18285-2005"Limits and Measurement Methods for Exhaust Pollutomts from Vehicles Equipped Igintion Eigine under Two-speed Idle conditions and simple Driving Mode Conditions".The system can select the prompt mode of the dirver mode or the prompt mode of lattice screen.
-
Product
Digital Inspection Camera
MaxiVIDEO MV108S
-
It turns your Autel tablet into a video inspection scope, allowing you to examine difficult-to-reach areas hidden from sight. It is capable of recording digital still images and videos. Includes mirror, hook and magnet attachments.
-
Product
Pinhole Detection Inspection Kit
Elcometer 270
-
The Elcometer 270 Pinhole Detectors Inspection Kit utilises the wet sponge technique and has been designed to set a new standard for wet sponge detectors - a high quality, low voltage detector with similar accessories to a high voltage spark tester.
-
Product
Calibration / AVP Service
-
Comware Technical Services, Inc.
Regular calibrations / AVPs will help ensure the measurement integrity of your system. We supply the calibration equipment or you can provide us with your own in-house equipment.
-
Product
STEEL PLATE INSPECTION MACHINE
-
Yubain Steel Plate Inspection Machine can effectively detect steel plate problems, including pinholes, hole breaks, hole deviations, leaks, multiple holes or few holes... and other shortcomings, which can help customers efficiently inspect incoming materials and inspections in the manufacturing process. , To avoid product damage due to steel plate problems, reduce financial losses and customer complaints.
