Compression
the result of being pressed.
See Also: Force, Crimp Force, Pull Force, Pull off Force, Push Pull Force, Peeling, Tension, Gravity, Electrical, Magnetic, Crush, Extensometers, Bending
-
Product
Package Testing
-
Lansmont package testing equipment is designed to perform industry standards, such as ASTM, ISTA, ISO, EUMOS and others. Our equipment is compliant with all of the most common ASTM and ISTA package testing procedures. There are individual standards that specifically reference how to perform drop testing, compression testing, side impact testing and vibration testing. In addition to those standards, there are groups of procedures referred to as distribution simulation tests, which incorporate some strategic combination of testing inputs, with the idea of simulating a typical journey through the supply chain. Some of the most common distribution simulation standards that are performed globally are published by ASTM and ISTA.
-
Product
Mechanical Testing
-
A range of processes including:Tensile and Compression Load TestingA test piece or component is subjected to tension (or compression) until either a proof load is achieved or failure occurs.Testing can be carried out on both metallic and some non-metallic materials.
-
Product
Capture & Replay System
-
PacketStorm Communications, Inc.
The PacketStorm CRS is a packet capture and replay system with hardware time stamping at 10Gbps. The user specifies which packets to capture based on the filter parameters. Packet captures can be continuous or stop capture after a certain number of frames, bytes, or time. The 10G filters include: Source Address, Destination Address, Source Port, Destination Port, and Protocol. The CRS file management includes automatic file compression and decompression. Operation is via the console or the remote GUI. There are two CRS versions: 1U and Lunchbox. The 1U version is intended to be installed in a rack or on a test bench. The lunchbox version includes a keyboard, mouse, and monitor and is intended to be moved about between stations and labs.
-
Product
3-Component Quartz Force Rings And Links
-
Three-component dynamic force sensors are offered in both ICP® and charge output configurations for dynamic and quasi-static force measurement applications. Each utilizes an array of precision aligned, quartz sensing crystals. Measurements along the z-axis are proportional to applied compression, tension and impact forces. Measurements along the x and y axes are proportional to shear forces that are imposed upon preloaded crystals by the test fixture.
-
Product
Upsetting Testing Machine
-
JINAN PRCISION TESTING EQUIPMENT CO., LTD
The full-automatic rapid upsetting testing machine adopts hydraulic loading and manual control. The metal material applies pressure along the axis of the sample at room temperature or hot state to compress the sample, test the ability of the metal to withstand upsetting plastic deformation under the specified forging ratio, and display metal surface defects. It is mainly used in the upsetting test of metal materials such as iron and steel enterprises, standard parts manufacturers, and tool manufacturers to test the ability of metal to withstand upsetting plastic deformation under the specified forging ratio and display the metal surface characteristics.
-
Product
Voice/Audio Quality Analyzer
OPERA™
-
The OPERA™ Voice/Audio Quality Analyzer represents the latest developments to objectively evaluate and assure the quality of compressed voice and wide-band audio signals, based on modeling the human ear. With OPERA you can achieve a comprehensive analysis of the end-to-end quality of today's and next generation networks, such as VoIP, VoDSL, VoATM, ISDN, GSM, POTS, from the caller to the callee. Also, you can test the audio quality of compression formats such as MP3, AAC, AC3, Microsoft Windows Media, from the studio source to the receiver, or from the server to the client.
-
Product
Force Sensors
-
General purpose force sensors are offered in either stud or axial mounted configurations. They are internally pre-loaded and can be used for dynamic compression, tension, and impact force measurements. Tapped mounting holes on both ends of the radial connector style support link, platform, integrated link, and free-standing installations. The axial mounted type offers protection of the electrical connector and sensor cable from potential damage during drop testing and in free-standing installations. Supplied impact caps facilitate impact and drop force measurements.
-
Product
General Purpose Quartz Force Sensors
-
General purpose force sensors are offered in either stud or axial mounted configurations. They are internally pre-loaded and can be used for dynamic compression, tension, and impact force measurements. Tapped mounting holes on both ends of the radial connector style support link, platform, integrated link, and free-standing installations. The axial mounted type offers protection of the electrical connector and sensor cable from potential damage during drop testing and in free-standing installations. Supplied impact caps facilitate impact and drop force measurements.
-
Product
Fixed-Mount Thermal Camera
FLIR A50/A70 Image Streaming
-
FLIR A50 and A70 Thermal Image Streaming Cameras are the right choice for users who want camera control capabilities and image streaming over Ethernet, as well as flexibility to perform analytics and raw data collection on thermal characteristics using preferred software applications. With options for Wi-Fi, an integrated visual camera, compressed radiometric image streaming, and ONVIF S compatibility, these small and lightweight fixed-focus automation cameras will optimize process control and quality assurance to improve yield, product quality, through-put time, and lower costs.
-
Product
USB Audio/Video Codec
2253
-
Simultaneous encode/decode in a robust, compact unit Uncompressed + compressed outputs from one video input Low preview latency H.264 HP@L3, MPEG-4 ASP, MJPEG video compression AAC, G.711 audio compression, uncompressed PCM Text overlay Two general-purpose digital I/Os Industrial temperature range version available Transport Stream
-
Product
6U VPX FPGA Cards
-
Curtiss-Wright Defense Solutions
FPGAs have revolutionized the way digital signal processing (DSP) subsystems are configured. With a large number of gates, hardware multipliers, and high-speed serial interfaces, FPGAs enable sophisticated applications, including radar, signal intelligence, and image processing, which rely on repetitive processing that can be expressed in highly parallel form. FPGAs perform exceptionally well in FFTs, pulse compression, filters, and digital up/down converters.
-
Product
Ku Band Gain Control Amplifier
-
Expanding Teledyne RF & Microwave's existing line of high frequency amplifiers, microwave gain controllable amplifiers are designed and biased for critical performance applications. One example covers 10-13 GHz, offers 45 dB unattenuated small signal gain with 15 dB attenuation range. Typical gain flatness is ±0.5 dB, +35 dBm third order intercept point, +22 dBm minimum 1-dB gain compression, and 3.5 dB unattenuated noise figure 4.5 dB at full attenuation. This is only one of a series of microwave controllable amplifiers currently in production.
-
Product
Modulated Wideband Driver Amplifier
TBMDA2
-
The TBMDA2 modulated wideband driver amplifier is designed in order to create an inexpensive signal source for immunity testing of electronic building blocks and products. It is designed to be driven by the tracking generator output of spectrum analyzers. With its 1dB compression point of +27dBm, it can boost the output power of a tracking generator up to 500mW.
-
Product
MEP-C
100812
-
The MEP device model from ATX is perfect if you want to bring exceptionally high flexibility into your test and inspection area - with the simplest control via the compressed air valve. As a stand-alone fixture, your MEP-C is perfect for functional testing, final testing and smaller ICT applications up to 1000N.
-
Product
Manual Test Stands
-
Manual test stands offer basic force testing and economy.Lever models enable rapid testing of compression or tension, up to 220 lbf.Wheel-operated test stands enable precise control for either compression or tension and the force gauge remains in position when the wheel is released. Wheel stands are offered in a wide range of capacities from the 11 lbf capacity micro-movement stand up to 750 lbf models.
-
Product
Instron Materials Testing Software
-
Instron offers a comprehensive suite of materials testing software solutions designed to support a wide range of mechanical testing applications, from static tensile and compression to fatigue, impact, and melt flow. Built for precision and efficiency, these software packages provide powerful tools for test control, data analysis, and reporting, with support for industry standards such as ASTM, ISO, and EN. Whether for basic quality control or advanced research, Instron’s software solutions deliver flexible, user-friendly interfaces and robust data integrity features to meet the diverse needs of modern testing laboratories.
-
-
Product
CrumpleFlex Tester
TF117C
-
TESTEX Testing Equipment Systems Ltd.
The equipment tests a tube of fabric by twisting it through 90o stretching alternately compressing the tube at the same time. After completion of the test the fabric is tested for resistance to penetration by water. CrumpleFlex Tester is fitted with electronic pre-determined counter with automatic stop at a pre-determined number of cycles, also fitted with acrylic plastic interlock safety cover.
-
Product
Custom Compression Blocks & Spacers For Solid-State Battery Test Cells
CEP1
-
Precision-machined titanium alloy electrode posts, compression blocks, and spacers for solid-state battery test cells and electrochemical research. Available in custom sizes and configurations, these components provide stable mechanical support, reliable electrical contact, and excellent corrosion resistance.
-
Product
Thermostatic Chambers
-
Various test devices are available for tensile, bending and compression testing in specific environments.
-
Product
DC/AC High Current Probe
698
-
Unit is designed for use with digital multimeters,lab scopes or graphing meters. With 1000 Amp capabiltiy, this instrument can be used to test starting and charging systems. It can even be used to test relative compression when used with your lab scope or graphing meter.
-
Product
LT Range Broadband Power Amplifiers 20 MHZ - 1000 MHZ
LT Series
-
Class A solid stateBroadband (instantaneous single band): 20 MHz 1000 MHzTypical output power : 90 W CWLinear output power (1 dB compression) guaranted with harmonics <-20dBc:P1dB > 60 W and H < -20 dBc from 20 MHz to 80 MHz andP1dB > 75 W and H < -20 dBc from 80 MHz to 500 MHz andP1dB > 45 W and H < -20 dBc from 500 MHz to 1000 MHzAir cooling: self contained fansCan operate in full mismatch conditions without damageUpgradable to LT 160 possibleReliable, efficient and robust19" Rack3 years standard warranty
-
Product
Dynamic Mechanical Analysis
-
The DMA systems from Anton Paar perform dynamic mechanical analysis in torsion, tension, bending and compression at unprecedented precision. Whatever your DMA requirements are, the DMA systems from Anton Paar are efficiently and comfortably adapted to meet your needs. Use the systems for the dynamic mechanical analysis of solutions, melts, solid bars, films, foils, or reactive resins.
-
Product
Frequency Converter Characterization With Wideband Modulated Signal
N5245BQ
Network Analyzer
The N5245BQ provides the N5245B 50 GHz PNA-X network analyzer, application software and accessories for frequency converter measurements with modulated signal such as EVM, NPR and ACPR in addition to gain, gain compression, IMD and other measurements
-
Product
Testing Equipment
-
Our product line of material testing equipment can perform several different types of tests and on different types of samples in tension and compression. With our testing software Califort, simply press the green arrow and your tests and measurements start.
-
Product
Low Profile Compressive Load Cell
CCLP-1.0
-
Low Profile Compressive Load Cell – 0.5t to 20t
-
Product
Trace-Level Dilution Calibrator
Model T700U
-
Teledyne Advanced Pollution Instrumentation
The Model T700U is a microprocessor based calibrator for precision, trace-level gas analyzers. Using highly accurate mass flow controllers combined with compressed sources of standard gases, calibration standards are provided for multipoint span and zero checks using up to 4 gas sources.In addition to the features of the Model T700, the Model T700U is designed for the demanding requirements of trace-level measurements. The ability to calibrate and verify linearity for NO2 at levels below 50 ppb is difficult with standard calibrators. To overcome this limitation, the Model T700U ozone generator operates in two modes; a high range with similar performance to the Model T700 ozone generator, and a low range, or "fractional" mode, for producing accurate ozone levels down to 3 ppb. To ensure the highest accuracy of NO2 output, the calibrator measures the ozone concentration prior to performing a GPT, and the range is selected automatically by the Model T700U based on ozone concentration and flow specified by the user.
-
-
Product
Sand and Dust Chamber
-
Designed to test a product’s resistance to extremely dusty, desert-like environments, Thermotron’s D-27 Sand and Dust Chamber provides the capability of meeting specific automotive test standards. Powerful blowers intermittently blow compressed air up through finely powdered dust and then allow the dust to settle back down covering the product.
-
Product
Load Bank
-
Being the reckoned names in the industry, we offer world-class range of Load Bank that is manufactured with perfection. We offer in different configurations such as Resistive, Inductive, and Capacitive. Our entire product range has high compressive strength and ensures smooth operations. They are durable in nature and are delivered in stipulated time frame.
