Intelligent Electronic Device
a microprocessor that controls power equipment devices.
-
product
Intelligent Interface Card
Space Shuttle cPCI
The Shuttle Bus cPCI is an intelligent interface card providing all Launch Data Bus, Ground Data Bus, and Multiplex De-Multiplex Multiple Remote Terminal capability to the Shuttle Bus, as required by NASA specification 84K01203 (Hardware Specification, Launch Data Bus (LDB) and Ground Data Bus (GDB) Interface Board). In summary, this card provides all features and functions required to meet the above specification, in a cPCI platform, with Simplex & Half-Duplex modes provided. Specific operational modes provided include for LDB_BCT, LDB_MRT, GDB_BCT, GDB_MRT, BUS_MON, MDM_MRT, Primitive and Calibration modes.
-
-
product
Differential And I/Q Device Measurements
S96089B
The S96089B combines source-phase control of multiple internal or external sources with frequency-offset mode, enabling simplified test of I/Q modulators/converters, differential mixers, and harmonics or amplifiers.
-
product
4 Port Devices
Four port devices can be realized by joining two 3 port devices via the appropriate ports. As system performance requirements become more demanding, new design approaches must be adopted. These include Faraday rotation devices and phase shift circulators. The bandwidth and isolation limitations of 3 port devices are overcome through a distributed architecture that enables more ferrite material to be incorporated into the transmission path, thereby achieving an increase in the biasing magnetic field. Phase shift circulators can be designed to handle higher RF power than 3-port devices.
-
product
Electronic Pilot Balloon Theodolite
TEBAL 2
F. W. Breithaupt & Sohn GmbH & Co.KG
*Available in 12/2016*Observe, measure and transfer angles of elevation and azimuth of the flight of an ascending pilot balloon at predetermined time intervals to a tablet/laptop/PC*Determine wind speed and wind direction at certain air layers with an easy-to-use software*Ruggedized design*Easy to use*Quick measurement*Quality made in Germany*Reliable data and documentation
-
product
Electronic Kits & Modules
This kit contains everything you need to build, the microcontroller will be programmed with the latest firmware before shipping.
-
product
High Power DC Electronic Load
36000A Series（50KW / 60KW）
36000A Series has its own control and display panel, CC / CR / CV / CP / Dynamic modes, 150 sets Store / Recall memory which provides load set-up more efficiently, also can be remote controlled via GPIB、RS232、USB and LAN interface.SHORT time setting and SHORT_VH, SHORT_VL setting function, also can measure Short Voltage and Current.
-
product
Device Testing
The BTL Working Group (BTL-WG) has developed a test package which contains a set of testing procedures. These can be acquired and used by manufacturers to pre-test their products for BACnet compliance before they send their products to an RBTO (Recognized BACnet Testing Organization) for BTL Testing. The BTL Test Package is available on the test documentation page.
-
product
High Power DC Electronic Load
3350G Series（4KW~6KW）
Each 3350G Series module has its own control and display panel, CC / CR / CV / CP /Dynamic modes, also can be controlled via RS232、Ethernet、USB and GPIB interface.
-
product
Thermal Imaging System for Electronics Testing
ETS320
Whether the goal is product testing or scientific research, heat can be an important indicator of how a system is functioning. The FLIR ETS320 is a non-contact thermal measurement system that pairs a high-sensitivity infrared camera with an integrated stand, for hands-free measurement of printed circuit boards and other small electronics.
-
product
IOT Device Management Platform
The Internet of Things revolution is ongoing and has gained significant traction over the last few years. This revolution is based on the availability of huge amounts of information coming from the data sensed and transmitted by intelligent connected objects. In order to cope with this revolution, the importance of efficient and reliable monitoring and management tools has increased significantly.
-
product
MODEM SHARING DEVICES
The Modem Sharing Devices are designed to allow RS-232 DTE (terminal) devices to share Leased Line and Dial line Modems or DSU's. Data arriving at the Master Port is continually broadcast to all Subchannels. The attached terminal device that raises the RTS control signal is automatically given control of the MSD. Data rates of up to 128 Kbps are supported.
-
product
Intelligent Vibration Sensing Gateway
From sensor, data acquisition, edge computing to AI utility, Advantech offers well-integrated solutions for clients to easily deploy a PHM system.
-
product
Battery Electronics
CAES Battery Electronics provide autonomous, dissipative, and continuous cell balancing to maximize available battery capacity, and therefore battery cycle life, throughout a mission.
-
product
Multipurpose X-Ray Diffractometer with Built-In Intelligent Guidance
SmartLab SE
The SmartLab® SE is a highly versatile multipurpose X-ray diffractometer with built-in intelligent guidance. It offers continued refinement of the original ease of use features that enabled the original SmartLab to receive the R&D 100 Award in 2006: automatic alignment, component recognition, cross beam optics and advanced photon counting hybrid pixel array detectors (HPAD).
-
product
High Voltage DC Electronic Load
3360F Series（600W~14.4KW）
3360F has its own control and display panel, CC/CR/CV/CP/Dynamic modes, 150 sets Store/Recall memory which provides load set-up more efficiently, also can be remote controlled via GPIB, RS232,USB and LAN interface.
-
product
Electronic Flow Meters
5050
Parker Conflow’s Code 5050 is an electronic flowmeter that has a user-friendly display and is used for measuring and outputting flow rate, pressure and temperature
-
product
IEC61588 Mandrel Test Device
CX-KD13
Shenzhen Chuangxin Instruments Co., Ltd.
This Mandrel Test Device conforms to IEC60588-1 Fig6 and IEC60065 Fig14--16.The test shall be performed by fixing the specimens of thin sheets on a mandrel made of nickel plated steel or brass with smooth surface finish.
-
product
Battery Test device
ATGB 1200
The ATGB 1200 is a battery tester for all standard battery technologies aimed at quality assurance, production and product development. Advantages of the ATGB: Creation of customized test sequences. Generation of load curves and peaks. Temperature measurement at the battery
-
product
High Power DC Electronic Load
34000C Series（6KW~24KW）
34000C Series has its own control and display panel, CC / CR / CV / CP / Dynamic modes, 150 sets Store / Recall memory which provides load set-up more efficiently, also can be remote controlled via GPIB、RS232、USB and LAN interface.
-
product
Bench Electronic Loads
EL30000 Series
The Keysight EL30000 Series Bench electronic load with a built-in data logger provides new levels of test insights for your devices like power supplies, batteries, DC to DC converters, and more. View voltage and current trends to make real-time decisions, rather than waiting hours for a test to complete. At the heart of the EL30000 is a highly accurate measurement system that provides real-time updates to the large display. Keysight’s PathWave BenchVue software allows you to operate the electronic load remotely, execute test sequences, log data, and integrate with other test instruments. Single and dual-channel models are available with up to 600 W for measurements that require more power. Start your test with confidence and finish with results you trust.
-
product
HighFfrequency Test Devices
VI Systems now releases engineering prototype samples of high performance transmitter and receiver optical subassemblies (TOSAs and ROSAs) for 25 Gbit/s and 40 Gbit/s applications and product development.
-
product
Electronic Loads
AMETEK Programmable Power, Inc.
Electronic loads have found a variety of applications ranging from power converter testing to current modulation. A large range of power sources can be tested using an electronic load from converters, inverters and UPSs to electrochemical sources such as batteries and fuel cells.
-
product
Multi-channel DC Electronic Load
IT8700 Series
IT8700 series programmable DC electronic load adopts removable modules design, supports up to 16 channels with mainframe extension transient mode up to 25 kHz, which improves your test efficiency, with high resolution and accuracy. Users can freely choose in the 8 load modules according to the number of channels and power requirements, controlled by mainframe control panel, or controlled by host computer software via built-in LAN / RS232 /USB / GPIB interface.
-
product
SF6 Gas Recovery Device
Weshine Electric Manufacturing Co., Ltd
SF6 gas recovery device is used for the manufacture and use of SF6 gas insulated electrical equipment and the recovery of SF6 gasin scientific research departments. It also has the ability to purify SF6 gas, vacuum and charge.It can vacuum SF6 electrical switch and measure the vacuum degree.It can fill SF6 gas into SF6 electrical switches.It can recover the gas of SF6 electrical switch.It can purify the recovered SF6 gas.Store SF6 gas.
-
product
Infusion Device Analyzers
Dual Channel with unique "Synchro-Start" function optimize IV Pump and Analyzer accuracyTest all types of pumps dual-rate, pulsatile flow, and PCA infusion pumpsAutosequence editing, plus test results
-
-
product
Electron Microscope Sample Preparation
Excellent sample preparation is the prerequisite for first-class electron microscopy. Be prepared – for great results in EM Sample Preparation! Perfect preparation makes the difference between trying and achieving, between failure and success, between results and excellent results. So be prepared for great results with Leica Microsystems!
-
product
Electronic Loads
PeakTech Prüf- und Messtechnik GmbH
Can be used for important test procedures in quality assurance as well as e.g. testing of power supplies and control units, batteries, fuel and solar cells. For precise load control for various purposes, this device offers load control according to constant voltage (CV), constant current (CC), constant load resistance (CR) or constant power (CP) with a highly precise resolution of 1mW, 1mV, 1mΩ and 1mA. The device also offers additional test modes, e.g. the battery test or the dynamic test. The PC interface and software offer the option of implementing freely programmable test sequences with data evaluation.
-
product
BAW Devices
Teledyne’s Bulk Acoustic Wave (BAW) Product Line has been producing BAW delay devices since the early 1960’s. Over the years, Teledyne Microwave Solutions (TMS) has constantly improved BAW technology and is currently the world’s only supplier of microwave bulk acoustic wave delay devices. Markets for BAW devices include instrumentation and radar altimeters and are available in connectorized, pin and surface mount configurations.
