Fuel Cell Test Systems
-
Product
ARINC-708/453 2-Channel Test & Simulation Module for the Weather Radar Display Databus
M8K708
-
The M8K708 module is an ARINC-708 / 453 2-channel test and simulation module for the Weather Radar Display Databus. The M8K708 supports two ARINC-708 / 453 channels, each selectable as transmit or receive. Each channel implements an 64K×16 FIFO and supports polling and/or interrupt driven operation.The M8K708 comes complete with Windows software, a C-driver software library including source code and may be used with Exalt, Excalibur’s Analysis and Laboratory Tools, a Windows monitoring application. In addition, Excalibur produces adapter cables that convert the carrier board I/O Molex™ connector to two twinax CJ70-49 connectors. The cable may be purchased at an additional cost.
-
Product
Optics Test Systems
Lens Test
-
Optik Elektronik Gerätetechnik GmbH
LensTest enables the measurement of air gaps, lens thickness, lens radii and lens surface centration errors in mounted lenses as well as the active alignment of lens surfaces during optics assembly for centering without rotating the assembly.
-
Product
Cells and Electrodes
-
Electrochemical cells are designed to their special purpose. The method, the matter and their reactions as well as the environmental conditions define the limitations and demands for electrochemical cells and the electrodes. Standard corrosion testing cells may have a large volume, since corrosion products shall not change the solution grossly during the test. On the other hand, it may be valuable to collect corrosion products - then a very small volume is desired ("eluation cell"). Special corrosion tests for pitting reqiure a setup where undesired crevice corrosion is excluded ("Avesta cell" , "Quarfort Cell" or "Flushed port cell". Or you want to investigate in crevice corrosion, then the cell design should meet such conditions. Have a look to the variety of cells shown here, and call us if you have a special task where a fresh design is required.
-
Product
Meter Testing System
ASTel
-
Three-phase Meter Test Equipment of ASTeL 3.2x.x series system is a fully automatic system enabling simultaneous, multi-position calibration and legalization of electric energy meters. The automatics include power sources, reference standards, stand controllers, photoelectric scanning heads, separating transformers, and other elements of the system. All these elements are controlled through a Windows based executive program.
-
Product
Isolated Digital I/O 60VDC, 150mA
OTP2 module no.186
-
The National Instruments PXI-6528, PCI-6528, and PXI-6529 Digital I/O Modules are isolated digital I/O interfaces for PCI and PXI. These modules can use inputs from NI 6528 and PXI 6529 devices to capture the status of sensors, actuators, and logic devices. NI 6528 devices have 24 SSR outputs for switching external devices with input currents up to 150 mA. The NI 6528 and PXI-6529 devices are suitable for a variety of applications, from automotive development and industrial factory automation to aerospace, laboratory research, and biomedical applications due to their high current handling capacity and isolation.
-
Product
Test Port Adapter Set, 3.5 Mm To 3.5 Mm
85130D
-
The Keysight 85130D test port adapter protects the test set port from being directly connected to the device under test. These adapters have a special rugged female connector that connects to the network analyzer test port. This special connector does not mate with a standard male connector but converts the rugged test set port to a connection that will mate with the device under test. This set contains a 3.5 mm to PSC-3.5 mm male adapter and a 3.5 mm to PSC-3.5 mm female adapter. The frequency range for these adapters is dc to 26.5 GHz with a return loss of 28 dB or better.
-
Product
Laser Diode Burn-in Reliability Test System
58604
-
The Chroma 58604 is a high density, multi-function, and temperature controlled module for laser diode burn-in and lifetime tests. Each module has up to 256 SMU channels which can source current and measure voltage in various control modes as described below.
-
Product
VLF Test System
BAUR PHG 70 portable
-
Portable, high performance test generator with VLF truesinus technology. The BAUR PHG 70/80 portable VLF test systems are used for cable and cable sheath testing of medium-voltage cables of up to 50 kV and electrical equipment.* 3 voltage shapes in one device: VLF truesinus, VLF square wave and DC voltage* For medium-voltage cables of up to 50 kV operating voltage* Cable testing, fault conditioning, cable sheath testing
-
Product
Resonant Testing System
-
Originally designed to precrack specimens for fracture mechanics, the current versions offer much more possibilities due to a modular concept:*Bending up to 160 Nm*Tension/Compression up to 8 kN*Torsion
-
Product
Nanomechanical Test Systems
-
Bruker’s nanomechanical test systems deliver the highest degree of performance, accuracy, reliability, and versatility for quantitative mechanical and tribological characterization at the nanoscale and microscale. Utilizing multiple patented and proprietary technologies, the Hysitron product line of standalone nanomechanical test systems enable quantitative characterization at length scales unreachable by others. Combined with the most comprehensive suite of hybrid characterization techniques, the TI 990 TriboIndenter, TI 980 TriboIndenter, TI Premier Series, and TS 77 Select nanoindenters will keep your materials development at the forefront of technology.
-
Product
The Compact AI GigE Vision Systems for the Edge with Intel Movidius Myriad VPU
EOS-i6000-M Series
-
The ADLINK AI Plug-and-Play (PnP) Solution is a set of ADLINK AI edge hardware and data connectivity platforms that help our partners build and deploy AI solutions faster and simpler. With ADLINK Data River™ enabled at AI edge platforms, devices, AI inferences, and data integrations, the AI PnP Solution offers a crossplatform, flexible, scalable solution that delivers business value.
-
Product
Vibration Test Systems
G-0 Series
-
The G-0 Series Vibration Test Systems consist of all-round, rugged, high quality vibration generators energy-efficient solid-state PWM power amplifiers, ideally suited to any vibration tests requiring high reliability such as MIL, IEC and JIS standardized tests for aircraft, automobiles, electronic components, electric apparatus and aerospace equipment.
-
Product
Automotive Test Systems
-
Ono Sokki Automotive Test Systems - flow meter, non-contact speedometer, engine tachometer, crank angle detector, and more
-
Product
Microtester Test Systems
-
With the micro probes and the fine-pitch adapters used on them, you are able to contact the finest test structures. E-tests, functional tests, IC tests or high-current tests are made to be affordable, efficient and with a short cycle time. With the integration of HF adapters we also enable the double-sided testing of HF substrates up to high frequency ranges.
-
Product
Fuel Pressure Testers
-
• Developed with input from technicians on adaptor selection for 7.3 L, 6.7 L, 6.4 L and 6.0 L Ford®Power Stroke®engines• 0 100 PSI gauge and hose assembly• Low-pressure diesel-fuel delivery testing (lift pump)• Correct fuel delivery and dynamic fuel pressure are crucial to having a properly running engine• Helps prevent a lean condition that may cause burning of injectors or scorched cylinders• Convenient protective slide-lid case that will fit in a 4" drawer for easy tool access• Technical Support: 1-866-713-6007
-
Product
Multipurpose Mobile PXI DAQ System
-
The mobile DAQ system achieves seamless integration among signal conditioning, data acquisition, and synchronization that benchtop instruments would not have achieved. By choosing this system over using benchtop instruments, United Technologies Research Center saved hundreds of thousands of dollars.
-
Product
Dynamic Test System
3430-SW
-
The Dynamic Test System 3430-SW measures dynamic characteristics of IGBT/MOSFET devices at high speed. Maximum of 4 parallel measurement is available by connecting the 3430-SW mainframe test stations for each test items ( normal 2stations). One PC controls the whole system.
-
Product
olar Cells and Modules Online Measurement System
PV-LIT
-
The fully automatic PV-LIT testing system offers individual and serial testing options for solar cells and complete solar modules. The modular testing system allows easy integration into existing production lines and can be used in automated serial testing for quality assurance.
-
Product
Voltammetry Cell
VC-4
-
Capable for measuring of 1 - 3 ml of sample volume using electrodes with 6 mm of the diameter. Furnished holder prevents the vial from spilling.
-
Product
Relay Testing System
UNO
-
With high power outputs package in an extremely compact and rugged system, the UNO has a tremendous power-to-weight ratio. The design incorporates the latest in modern digital microprocessor technology to achieve unbeatable output characteristics in terms of power, accuracy, low distortion, and dynamic capability. This hi-tech solution enables the testing of many different functions required in relay testing without the need of additional accessories.
-
Product
Conformance Test System
TS8980
-
The R&S®TS8980 is the most compact full range conformance testing solution on the market for testing in line with requirements from GCF, PTCRB and regulatory bodies. It supports the entire device certification process for RF and RRM, covering the widest range of technologies including 5G NR based on 3GPP and carrier acceptance specifications. The test system is available in various configurations to cover the required scope of testing.
-
Product
Ventilator Test System
4070
-
The Certifier® FA Ventilator Test System 4070 is capable of testing multiple parameters of ventilator performance. It is designed to measure air, oxygen, and nitrous oxide flow and pressure in institutional, home care, field service, laboratory, and production applications. The Certifier FA ventilator test system is a battery-operated flow analyzer that can also test a variety of other medical equipment such as anesthesia gas delivery machines and oxygen concentrators.
-
-
Product
Flight Control System Test Platform
-
The Flight Control System Test Platform provides a hardware in-the-loop (HIL) closed-loop test environment for dynamic and maintenance testing of Flight Control Systems (FCS) of both commercial and military aircraft. The system simulates control surface activities from multiple combinations of rudder, flaps, elevator, aileron, and engine controls to the FCS. The system delivers repeatable, cost-effective testing in a fraction of the time needed with typical in-house simulation test systems.
-
-
Product
Laser Test Systems
-
Santa Barbara Infrared, Inc. offers an extensive family of test systems and components that test and characterize the performance of laser range finders, designators, illuminators and spot trackers.
-
Product
Universal Testing Systems
-
Instron universal testing systems are versatile, high-accuracy platforms (available in electromechanical and hydraulic variants) designed to perform a wide range of static mechanical tests, such as tension, compression, bend, peel, shear, puncture, and more, on virtually any material. They support force capacities from fractions of a newton up to thousands of kilonewtons, with precision load measurement, high data acquisition rates, and compatibility with thousands of accessories, including a wide range of extensometers, grips, fixturing, and automation solutions to meet demanding quality and throughput standards.
-
Product
Portable Fuel Analysis
MINISCAN IR Vision
-
The MINISCAN IR VISION is a high speed, compact and robust FTIR fuel analyzer for the comprehensive and automatic measurement of gasoline, jet and diesel fuels. The analyzer is configured to measure more than 100 fuel parameters and components for fuel blending, for quality inspection and to check compliance with fuel specifications directly at the point of sale.
-
Product
Tire and Wheel Testing Systems
-
Advanced Telemetrics International
Tire and Wheel Testing Systems can be custom designed and manufactured for practically any application. The inductively powered system is used to wirelessly measure tire pressure and temperature during testing.
-
Product
GTEM cells
-
Meets IEC/EN 61000-4-20, SAE J1752/3, IEC 62132-2 and IEC 61967-2. The GTEM cell is, in principle, a tapered coaxial line (offset septum plate), which is terminated by a hybrid combination of discrete resistors and RF absorbers to achieve a 50 Ohm broadband match. It is applied for Measuring of Emission, Radiated, radio frequency field-immunity test.
