Filter Results By:
Products
Applications
Manufacturers
ADC
quantization of an analog signal into a digital signal.
See Also: Analog-to-Digital Converters, FPGA, Transducers
-
product
8-Channel ADC Module
FMC108
Sundance Multiprocessor Technology Ltd.
The FMC108 is an eight-channel ADC FMC (FPGA Mezzanine Card) which is fully compliant with the VITA 57.1-2010 standard. The FMC108 card provides eight A/D 14-bit 250MSPS channels which can be sampled by an internal clock source (optionally locked to an external reference) or an externally supplied sample clock. A trigger input for customized sampling control is also available. The FMC108 has the HPC (high-pin count) connector, front panel I/O, and is conduction cooled compliant. The board is also available with Mil-I-46058c compliant Conformal Coating.
-
product
Infiniium S-Series High-Definition Oscilloscope: 4 GHz, 4 Analog Channels
DSOS404A
4 GHz bandwidth (upgradable)4 analog channels Capture a longer signal trace with 20 GSa/s max sample rate and 100 Mpts/channel of standard memory Get superior signal integrity with system ENOB of 7.2 bits and 10-bit analog-to-digital converter (ADC)Gain increased usability with the multi-touch supported 15 inch capacitive touch screen and solid state drive for fast boot and reliability Improve your testing with a wide range of protocol, compliance, and analysis software
-
product
64 Channel ADC for VMEbus
VME392
The VME392 features 64 self-contained ADC channels with a resolution of either 12 or 16-bit (see ordering information). This product is ideally suited for mass acquisition with high accuracy for reasonable cost. The 64 channels are grouped into four sections of 16 channels each. Each section behaves completely independent from the other sections.
-
product
PXIe 14 Bit High Speed Digitizer - 400 MS/s on 2 Channels
M4X.4480-X4
The M4x.44xx-x4 series digitizers deliver the highest performance in both speed and resolution. The series includes PCIe cards with either two or four synchronous channels where each channel has its own dedicated ADC. The ADC’s can sample at rates from 130 MS/s up to 500 MS/s and are available with either 14 bit or 16 bit resolution. The combination of high sampling rate and resolution makes these digitizers the top-of-the-range for applications that require high quality signal acquisition.
-
product
Digital MultiMeter
12061
Chroma Systems Solutions, Inc.
The 12061 6½ Digital Multimeter has assorted settings for resolution, integration time and ranges that allow users to optimize the configuration of measurement speed, resolution and accuracy when in individual measurement test modes. The 12061 has built-in a high speed, low interference A/D converter with a maximum speed of 2000 rdgs/s, making it the best solution for high speed measurement.
-
product
Octal 1.4 Gsps, 14-bit ADC FMC+
ADF-O1414
The ADF-O1414 ADC FMC+ module from DEG delivers eight channels, each with 14 bits of resolution at a sample rate of 1.4 Gsps. Utilizing the Analog Devices AD9695 ADC, the ADF-O1414 enables defense applications requiring higher dynamic range, greater ENOB and wideband sampling performance.
-
product
T3DSO2000A Series Oscilloscopes
T3DSO2000A Series
Teledyne Test Tools T3DSO2000A Oscilloscopes feature two channel and four channel models with analog bandwidth options from 100 MHz to 500 MHz. Each model offers a maximum sample rate of 2 GSa/s, and a maximum memory depth of 200 Mpts in half channel mode. All models incorporate two 2 GSa/s ADCs and two 200 Mpts memory modules. When all channels are enabled, each channel has sample rate of 1 GSa/s and a standard record length of 100 Mpts. When only a single channel per ADC is active, the maximum sample rate is 2 GSa/s and the maximum record length is 200 Mpts. For ease-of-use, the most commonly used functions can be accessed with its user-friendly front panel design.
-
product
USB-7845, Kintex-7 70T FPGA, 500 kS/s Multifunction Reconfigurable I/O Device
783200-02
Kintex-7 70T FPGA, 500 kS/s Multifunction Reconfigurable I/O Device - The USB‑7845 features a user-programmable FPGA for high-performance onboard processing and direct control over I/O signals for complete flexibility of system timing and synchronization. You can customize these devices with the LabVIEW FPGA Module to develop applications requiring precise timing and control such as hardware‑in‑the‑loop testing, custom protocol communication, sensor simulation, and high-speed control. The USB‑7845 features a dedicated A/D converter per channel for independent timing and triggering. This design offers specialized functionality such as multirate sampling and individual channel triggering, which are outside the capabilities of typical DAQ hardware.
-
product
Modular High-Quality Audio Conversion System
DREAM ADA-128
The Dream ADA-128 redefines flexibility, capacity, and performance standards in professional audio conversion. In creating it, we ripped up the rule book and started again, using all our 30+ years of ADC and DAC development experience. Building on the legacy of the Prism Sound Dream ADA-8XR, the resulting Dream ADA-128 architecture is so capable that it is set to meet the needs of the most demanding facilities for years to come.
-
product
4-20mA Input A/D Converters
Analog Devices range of 4-20mA Input A/D Converters deliver accuracy, robustness and flexibility for Industrial Control applications. As the world’s leading supplier of data converters, Analog Devices is constantly introducing new A/D converters (ADCs) that drive system level architectures. Our portfolio of leading industrial 4-20mA Input A/D Converters offer considerable integration including, sense resistor, signal conditioning circuitry and advanced on-chip diagnostics to maximize performance and provide an integrated system level solution, all based upon robust silicon processes.
-
product
Standard High Speed A/D Converters
Analog Devices high speed A/D converters (ADCs) offer the best performance and highest sampling speed in the market. The product offerings include low IF A/D converters (20 MSPS to 125 MSPS), high IF a/d converters (125 MSPS to 1.3 GSPS), and wideband ADCs (>1 GSPS). The high speed a/d converter portfolio offers cost and performance optimized solutions for various applications such as communications infrastructure, electronic test and measurement, and aerospace and defense.
-
product
Torque Instrument
DTR is a microprocessor based digital indicator, totally autonomousand with input for strain gauge based torque transducers.A ≤±0,02% accuracy makes it possible to be used use in qualitysystems as first or second line sample, periodically calibrated by aSIT center. Measuring system consists of a particularly long-termstable analogue section, of a carrier frequency amplifier whichminimises thermal drifts and of a 16 bits A/D converter whichensures 65.000 internal divisions.
-
product
Module Spectrum
nRF52833 Series
Nordic nRF52833 solutioin features an Arm Cortex-M4 processor with 512 KB Flash and 128 KB RAM. Supports SPI, UART, I2C,I2S, PMD, PWM, ADC, NFC and USB interfaces
-
product
Infiniium S-Series High-Definition Oscilloscope: 2 GHz, 4 Analog Channels
DSOS204A
2 GHz bandwidth (upgradable)4 analog channels Capture a longer signal trace with 20 GSa/s max sample rate and 100 Mpts/channel of standard memory Get superior signal integrity with system ENOB of 7.5 bits and 10-bit analog-to-digital converter (ADC)Gain increased usability with the multi-touch supported 15 inch capacitive touch screen and solid state drive for fast boot and reliability Improve your testing with a wide range of protocol, compliance, and analysis software
-
product
Taper System, CCD Beam Imaging Camera
TaperCamD series
355 to 1150 nm, standard CCD detectorHyperCal Dynamic Noise and Baseline Correction software (Pat. Pending)CTE Comet Tail Elimination for > 900 nm (Pat. Pending)Port-powered USB 2.0; flexible 3 m cable, no power brick14-bit ADC, 4 MB image buffer & on-board microprocessorWindow-free sensors standard for no fringing25,000:1 electronic auto-shutter, 40 s to 1000 ms1,000:1 SNR (30/60 dB Optical/Electrical)
-
product
Oscilloscope
RTM3000
Designed as daily problem-solving tool, the R&S®RTM3000 combines the power of ten (10-bit ADC, 10 times the memory and 10.1" touchscreen) with a Rohde & Schwarz probe interface for all Rohde & Schwarz probes.
-
product
Transmitter (Export Only)
SMB
The input section features the unique servo bias input circuitry with a standard TA5M type jack for use with electret lavaliere mics, dynamic mics, or line level signals. A DSP-controlled analog audio limiter is employed before the A-D converter. The limiter has a range of more than 30 dB for excellent overload protection and a dual release envelope that makes the limiter acoustically transparent while maintaining low distortion. The limiter recovers quickly from brief transients, with no audible side effects, and also recovers slowly from sustained high levels to keep audio distortion low while preserving short term dynamics.
-
product
Digital Panel Meters
Built-in Bezel at no additional charge3, 3 1/2 or 4 1/2 Digit ReadoutAuto Calibrating, Auto Zeroing, A/D Converter Operation from single +5V supply or 9V battery (low power units)Large easy to read LED or LCD displayOptional Backlighting on LCD ModulesUser Selectable decimal point placement(all models) Built-in color filter on all LED modulesLED colors available, Red (std)Yellow, green, amber, aqua, orange, blue
-
product
Signal Chain µModule Receivers
µModule®
Analog Devices µModule® (micromodule) receivers consist of high performance, high speed ADCs with fixed-gain, high speed amplifiers and antialias filters. Our integrated ADC and driver products include integrated bypass capacitance and simplify the high frequency layout required to preserve ac performance. The board space savings are significant for instrumentation applications such as spectrum analyzers, oscilloscopes ,and communications test equipment, or for communications applications such as high sensitivity receivers, software-defined radio (SDR), or signal intelligence receivers. Our portfolio uses system-in-package (SiP) technology similar to multichip modules (MCM) to integrate components with different technologies, along with passive components to make an integrated subsystem.
-
product
14-Bit, 2.6 GSPS, JESD204B, Dual Analog-to-Digital Converter
AD9689
The AD9689 is a dual, 14-bit, 2.6 GSPS analog-to-digital converter (ADC). The device has an on-chip buffer and a sample-andhold circuit designed for low power, small size, and ease of use. This product is designed to support communications applications capable of direct sampling wide bandwidth analog signals of up to 5 GHz. The −3 dB bandwidth of the ADC input is 9 GHz. The AD9689 is optimized for wide input bandwidth, high sampling rate, excellent linearity, and low power in a small package.
-
product
High Speed Digitizers
High performance and high speed digitizers with wide bandwidth and high dynamic range. Featuring high-speed Analog-to-Digital Converters (ADC) with Real-Time Field Programmable Gate Array (FPGA) based digital processors. Long acquisition memory coupled with fast PCIe offload and streaming over optical data interfaces (ODI).
-
product
Intelligent A/D I/O Unit
RAD242
Model RAD242 is an intelligent, two-differential-channel, 24-bit analog-input interface unit that includes a Delta-Sigma A/D converter. The converter has a digital output filter with adjustable notch frequency from 10 Hz to 2000 Hz. The pod also has 13 bits of digital input/output. A precision 10 VDC voltage that can be used for transducer excitation is available at connector pin 5. As much as 60 mA current can be provided. It is packaged in a NEMA 4 enclosure for remote installation in harsh environments. RAD242 also provides a user-definable interrupt input and counter/timer input. An optional RAD Firmware Development Kit is available if you wish to use those user-programmable input lines or to develop a custom program.
-
product
6ch ADC, 2ch DAC – High-Pin-Count
RFM-ADAFF62
Sundance Multiprocessor Technology Ltd.
The RFM-ADAFF62 is a six channel Analog to Digital and two channel Digital to Analog mixed converter FMC which complies with VITA 57.1-2010. Each AD channel provides AC coupled single-end analog input and 16-bit single-ended output with 20-105MHz sampling speed based on ADI AD9650. Each DA channel provides 16-bit single-ended input and one DC coupled differential analog output with 1 – 500MHz sampling speed based on Maxim MAX5888A.
-
product
ATE For ADC Module
MS 1527
The Semi-ATE is used for testing the analog ADC. It shall carry out the functional test on ADC analog module. The ATE shall have all necessary IO signals on the connector end. The semi-ATE can carry out the functional tests on ADC analog module with host PC or laptop. It provides +15V, -15V, +5V & -5V to module and +2.5V high precision reference voltage. It can able to control keysight N6700B Power supply mainframe using RS422 interface.
-
product
Vibrator Control System
FORCE-III
The Force 3 Vibrator Control System is the newest generation of vibrator control system. It is designed to control individual vibes, or synchronize entire fleets of trucks. Using GPS, or VHF/UHF radio, for its time base the Force 3 both starts the Vibrator and controls its sweep with unparalleled precision and accuracy.The Force 3 is equipped with the latest ADC chips for better sweep resolution, increased computing power for faster response, GPS for precise source location, 8 Gbytes of internal memory for integrated VSS and PSS data storage, and integrated Wi-Fi for easy data offloading.
-
product
Portable 2 Channel/4 Channel FFT Analyzer
CF-9200/9400
The CF-9200 and CF-9400 are an all-in-one portable FFT analyzer. All FFT analysis operations can be performed with the integrated hard keys and capacitance type touch panel without requiring an external PC for analysis. The new, exclusively developed 100kHz high-performance analysis front-end system incorporating a 24-bit A/D converter enables easier and more reliable analysis of noise and vibration generated by plant lines, pumps, motors, automobiles, railway vehicles, home electrical appliances and devices, and electrical and electronic parts than previous models. The CF-9200 and CF-9400 also offer solutions for field workers in their FFT analysis, including the resonance and frequency characteristics of mechanical structures in a vibrating environment with electromagnetic vibrators and impulse hammers.
-
product
Clock And Trigger Synchronization Board With Atomic Clock
CLKSYNC-PCI-AC
CLKSYNC-PCI-AC is a clock and trigger distribution board designed to provide up to eight synchronous clock and trigger outputs. The CLKSYNC-PCI-AC is designed for use with multi-channel, ADC and DAC systems where precise clock and trigger synchronization are required.
-
product
16-Channel RTD Signal Conditioning Card
ProDAQ 5821
The ProDAQ 5821 series of Signal Conditioning Cards is designed to interface with a variety of sensors, principally RTDs, Thermistors, Cryogenic Diodes and Voltage type sensors. Each version of the 5821 provides the capability of precise 4-wire measurement. In order to achieve this, a precise 500μA constant current source is provided per channel. The current source can be disabled on a per channel basis and is monitored to ensure that current is flowing. The value of the output current is stored on-board after calibration. In order to achieve the highest accuracy the output current may be automatically calibrated 'on-the-fly' using the ProDAQ 3416 24-bit Sigma-Delta ADC card and an on-board precision resistor.
-
product
Multifrequency Clock Synthesizer - PCIe
Model 7890
Simultaneous synthesis of up to five different clocks, Eight SMC clock outputs, Ideal for A/D and D/A converter clock sources, Typical phase noise: -125 dBc/Hz @ 1 kHz offset
-
product
1100-Channel GSM Channelizer wih Quad A/D - PCIe
Model 78663
Model 78663 is a member of the Cobalt® family of high-performance PCIe boards based on the Xilinx Virtex-6 FPGA. This fourchannel, high-speed A/D converter with1100 GSM DDCs (digital downconverters) accepts IF signals from an RF tuner. It is ideal for capturing all transmit and receive signals in both upper and lower GSM bands.
