Filter Results By:
Products
Applications
Manufacturers
-
product
Standard Air Capacitor Set, 1pF To 1000pF
16380A
The 16380A is a standard capacitor set consisting of four precision capacitors - 1pF (16381A), 10pF (16382A) 100pF (16383A), 1000pF (16384A). These capacitors are primarily used for performance tests of Keysight's 4-terminal pair LCR meters and impedance analyzers. Refer to the instrument's operation/service manual for the method of using these standards.
-
product
200KHz / 10000Freq.Point LCR Meter
MCH-2816A
It has high test frequency of 300kHz and 0.01Hz stepping arbitrary programming, and it has 10mV-2V signal level, all making it meet the precision test requirements of production line quality control, in-coming inspection and lab. Its HANDLER, RS232c interfaces are used for the component automatic sorting system, which provides the conditions for computer telecommunication and test recording. Flexible frequency-response analysis:Due to non-ideal inductor, capacitor and resistor, in order to precisely evaluate the characteristics of one component in one frequency band, MCH2816 could use its signal generation ability with 10mHz resolution to correctly analyze frequency response of the component parameters in any frequency band. In particular, it can do the precise measuring of the resonant impedance of the low-frequency ceramic resonant devices which has wide impedance range.
-
product
LCR Meters
PeakTech Prüf- und Messtechnik GmbH
A type of electronic test equipment used to measure the inductance (L), capacitance (C), and resistance (R) of an electronic component.[1] In the simpler versions of this instrument the impedance was measured internally and converted for display to the corresponding capacitance or inductance value. Readings should be reasonably accurate if the capacitor or inductor device under test does not have a significant resistive component of impedance. More advanced designs measure true inductance or capacitance, as well as the equivalent series resistance of capacitors and the Q factor of inductive components.
-
product
FAult Detector and OScilloscope 7 Functions in 1 Device
FADOS7F1
Prot-Ar-Ge Industrial Project Design R&D Ltd. Co.
Usage of FADOS7F1: Determining faults of all types of electronic cards such as electronic cards of medical devices, textile and any other machines; automobile electronics; computer, monitor, TV, etc. Electronic Components Test: IC, transistor, FET, IGBT, resistor, capacitor, indicator, ect. This device is used to determine the faults at all these electronic components.
-
product
PRECISION COMPONENT ANALYZER
6400 SERIES
The 6430B and 6440B Precision Component Analyzers provide thorough and accurate testing of any passive component to high resolution. In particular, for capacitor manufacturers, the instruments provide capabilities for both fast automatic production testing and complete design characterisation. Users include designers of passive components, manufacturing test, designing and testing materials as well as circuit designers who are evaluating component characteristics.
-
product
LCZ LCR Meter
SS1063
This (SS1061 / SS1062 / SS1063) LCZ Meters are a test system for passive components designed for the use in electronic inspection or production process for quality control. They meet any demanding requirement on production speed and precision, discrimination of qualified products from unqualified ones, as well as internal setup, storing and calling function for up to 10 instrument groups, so they Like as: transformer, inductor, resistor, capacitor, relay, motor, generator, eletric valve, contactor,cable,wire,etc.
-
product
50Hz-100kHz LCR Meter
11022/11025
Chroma Systems Solutions, Inc.
0.1% basic accuracyTransformer test parameters (11025), Turns Ratio, DCR, Mutual Inductance0Hz, 60Hz, 100Hz, 120Hz, 1kHz, 10kHz, 20kHz, 40kHz, 50kHz, 100kHz test frequencies21ms measurement time (≥100Hz)Agilent 4263B LCR Meter commands compatible4 different output resistance modes selectable for non-linear inductor and capacitor measuringHigh resolution in low impedance(0.01mΩ) and high accuracy 0.3% till 100mΩ rangeAdjustable DC bias current up to 200mA (constant 25Ω) (11025)1320 Bias Current Source directly control capability0.01mΩ ~ 99.99MΩ wide measurement range (4 1/2 digits)Dual frequency function (11022 option) for automatic productionBIAS comparator functionComparator function and 8/99 bin-sorting functionPass/fail judge result for automatic productionHandler interface trigger edge (rising/falling) programmableTest signal level monitor functionStandard RS-232, GPIB, and Handler I/FOpen/short zeroing, load correctionLabView® Driver
-
product
Vacuum Capacitor
The LBA Technology vacuum capacitors store maintains a large stock of all types of RF capacitors, both vacuum and mica capacitors. While LBA is a factory dealer specializing in COMET and JENNINGS fixed and variable vacuum capacitors, we can supply virtually any style, value, or manufacturer's product on special order. Typical of other brands supplied are Meiden, Sangamo, and Cornell Dubilier. We provide fast quotes and worldwide shipping. The high quality vacuum capacitors we stock and sell typically have capacitances from 3 pF to 6600 pF, and peak test voltages to 100 kV at 1000 amps. These include both fixed and variable styles. A full line of capacitor accessories such as cylometers, insulators, corona rings, and mounting hardware is available from LBA.
-
product
Atlas LCR Passive Component Meter
LCR40
The Atlas LCR40 automatically identifies and analyses almost any passive component (Inductor, Capacitor or Resistor). It measures its parameters using automatically selected test frequencies (DC, 1kHz, 15kHz and 200kHz).
-
product
R.F. Coupler and high Pass Filter
7415-3
There are those who disagree with the r.f. conducted susceptibility test setup of Method CS02 of MIL-STD-462. Homemade rigs have sprouted to comply with the coupling capacitor requirement, each with it own disadvantage. Our little Type 7415-3 R.F. Coupler is the answer. A neat little box with BNC connectors and a pair of binding posts, it is rated at 270 V.A.C. at the LINE terminals and 20 volts PMS into the GEN port. Looks good and does a fine job.
-
product
Decade Box, Calibrated W/D & U, Capacitance, 5, 100pF to 11111µF, 5 %
72-7265 CAL DU
The 72-7265 CAL DU from Tenma is a capacitance decade box. It is ideal for service, prototype and experimental use. This useful tool may be set at any non polarized capacitor value from 100pF to 11,111µF in 100pF increments. The decade accuracy is ±5% capacitors used throughout at <1μF, 1KHz test frequency, ≥1μF, 100Hz test frequency. It has weight of 304g/0.69lb and dimension is 14.7cm × 11.7cm × 5.5cm (5.79" × 4.61" × 2.16"). It is typically used in general applications, troubleshooting, maintenance, education and vocational training, production line testing, radio and TV services, working standards, research design & develop, physics laboratory work.
-
product
1kV DC Hipot Tester For Capacitor
AllWin Instrument Science and Technology Co., Ltd.
The max capacitor up to 50uFcharge time is 0~5s; test time is 1~99s( continue set)The max leakage current can up to 300mA
-
product
Electrolytic Capacitor Test & Scanning System
DU-9001
Delta United Instrument Co., Ltd.
The 10 capacitor - LCC/DZ/R in order to automatically scan test improve the test reliability and test efficiencyEach test channel can be opened / short circuit return to zero with high precision.Wide range scan box can be used to test 3mm~35mm 10 capacitorsSuitable for high voltage capacitance test, 450V330uF 10 capacitors can be smooth test
-
product
High Voltage Relays
B-1001
Air insulated types for isolating loads, tap selections, safety discharge & grounding to help meet OSHA and other safety regulations. Ratings from 1mA to 800 amps continuous, to 100,000 amps capacitor discharge. Peak 1 minute test voltages from 5kV to 300kV. Single or Multipole. Auxiliary contacts are optional on all types. Options include latching, extended life, and tungsten contacts available for high current closing. DC, 25-800Hz & air pressure actuation available. Also usable in oil or insulating gas with increased ratings.
-
product
Insulating Oil Dielectric Loss Tester
HDLT
Hention Electrical Equipment Co., Ltd.
This integrated precious insulation oil dielectric loss tester is for measuring dielectric loss TAN and capacitance of transformer insulation oil.This is a high precision instrument; integrated with oil cup, temperature control instrument, temperature sensor, dielectric loss test bridge, AC test power, and standard capacitor, etc.
-
product
Capacitance Tester
ZHANGZHOU HUAYI ELECTRONICS CO.,LTD.
Is a piece of electronic test equipment used to measure capacitance, mainly of discrete capacitors. Depending on the sophistication of the meter, it may display the capacitance only, or it may also measure a number of other parameters such as leakage, equivalent series resistance (ESR), and inductance. For most purposes and in most cases the capacitor must be disconnected from circuit; ESR can usually be measured in circuit.
-
product
Insulation Resistance Meters
Scientific Mes-Technik Private Ltd
General purpose insulation resistance meterAnalog indicator, High measurement speedTest voltage range: 10 V to 500 VSuitable for Test capacitor insulation testEasy operation
-
product
Voltage/Continuity Tester
CT-01
Standard Electric Works Co., Ltd
● Audible and optic continuity test.● Audible and optic voltage check.● Voltage protection : 600V● Robust and ergonomic housing.● For checking electric light bulbs, securings, wirings and so on.● Application : resistor, voltage, semiconductor, capacitor and so on.
-
product
Capacitance Standard Set, 0.01uF To 10uF
16380C
The 16380C is a standard capacitor set consisting of three precision capacitors - 0.01uF (16385A), 0.1uF (16386A), 1uF (16387A),and an optional 10uF (16388A). These capacitors are primarily used for performance tests of Keysight's 4-terminal pair LCR meters and impedance analyzers. Refer to the instrument's operation/service manual for the method of using these standards.
-
product
Battery Cell Testing Equipment
Xiamen WinAck Battery Technology Co., Ltd.
The battery cycle life tester is a high-precisionsystem designed specifically for the battery cell charge and discharge testing.It is suitable for the battery cell cycle test, battery cell charge anddischarge aging test, battery cell performance test, battery cell capacitydetection test, battery cell IR test, deep-discharging test, function test ofhigh-power lithium-ion battery cells, such as EV battery module, ES batterymodule, super capacitor…
-
product
Decade Box, Calibrated W/Data, Capacitance, 5, 100pF to 11111µF, 5 %
72-7265 CAL D
The 72-7265 CAL D from Tenma is a capacitance decade box. It is ideal for service, prototype and experimental use. This useful tool may be set at any non polarized capacitor value from 100pF to 11,111µF in 100pF increments. The decade accuracy is ±5% capacitors used throughout at <1μF, 1KHz test frequency, ≥1μF, 100Hz test frequency. It has weight of 304g/0.69lb and dimension is 14.7cm × 11.7cm × 5.5cm (5.79" × 4.61" × 2.16"). It is typically used in general applications, troubleshooting, maintenance, education and vocational training, production line testing, radio and TV services, working standards, research design & develop, physics laboratory work.
-
product
Transformer/Capacitor Test Sets
*Quick and easy check for opens or shorts on transformers or capacitors before energizing*Provides clear indications of open circuits, short connections and confirmation that the test results are OK*Tests overhead, pad-mount and other distribution transformers as well as capacitors and capacitor banks*Tests the primary and secondary sides of de-energized transformers and capacitors without disconnecting*Helps prevent line workers from installing a fuse on a shorted transformer or capacitor*Automatic self-test featureMagnet holds the tester in place while testing
-
product
Capaciter Tester
KS-1600
Konstar Electric Industrial Co., Ltd
It is a dial instrument, and has the stable function and high reliability. It is driven by the battery. The instrument makes use of the indicator plate(102*79mm), thus displays clearly.This instrument can test the data of on-line capacitive resistance and on line impedance. It is an excellent instrument and an ideal tool for the people in labs, factory and household. When testing the mounted capacitor, it does net need to be completely out of power nor do the meter, and the meter can be testing continuously.
-
product
LCZ LCR Meter
SS1062
This (SS1061 / SS1062 / SS1063) LCZ Meters are a test system for passive components designed for the use in electronic inspection or production process for quality control. They meet any demanding requirement on production speed and precision, discrimination of qualified products from unqualified ones, as well as internal setup, storing and calling function for up to 10 instrument groups, so they are actually optimum test instruments for component incoming and production inspection. Like as: transformer, inductor, resistor, capacitor, relay, motor, generator, eletric valve, contactor, cable, wire, etc..
-
product
High Voltage Capacitance & Tan Delta Test Set
*Aesthetically designed Single Unit consisting of Measuring Bridge, Power Supply with in-built Standard Capacitor. Ideal for field /portable applications.*Highly compact & Portable – Approx 66Kgs only.*Advanced Protection Circuitry –specially suitable for 400kV s/s applications.*Successfully passed all required EMI/EMC Tests at SAMEER Chennai IEC 61000-4-2;IEC 61000-4-3; IEC 61000-4-4; IEC 61000-4-5; IEC 61000-4-11;*Improved Plug-in type of “Power In” and “Gnd” connectors.*Preo 2 Stage RF Power line Filters incorporated for 230V Power Input and Bridge Power Input for improved EMI Power line Protection*Improved 2 sets of LV measuring cables.*Improved HV cable outer covering hosepipe for rugged field use.
-
product
Connector Test
A connector test system which provides expansion of up to 160 Kelvin pair connections. The system incorporates high voltage AC and DC power supplies with a maximum output of +/- 2100 Volts peak for Hi Pot, Insulation resistance measurement. LCR bridge control is provided with 4 terminal multiplexing in order to add precision capacitance, inductance and resistance measurement capability. An integral H.V. capacitor bias option permits capacitance measurement to be made at up to 2.1kV.
-
product
Capacitance and Inductance Tester
JY6700
Capacitance measurementsInstrument can test take a single capacitor without stitches in test group capacitance to bring convenience to test. It will show test results of capacitance while show test
-
product
Decade Box, Calibrated, Capacitance, 5, 100pF to 11111µF, 5 %
72-7265 CAL
The 72-7265 CAL from Tenma is a capacitance decade box. It is ideal for service, prototype and experimental use. This useful tool may be set at any non polarized capacitor value from 100pF to 11,111µF in 100pF increments. The decade accuracy is ±5% capacitors used throughout at <1μF, 1KHz test frequency, ≥1μF, 100Hz test frequency. It has weight of 304g/0.69lb and dimension is 14.7cm × 11.7cm × 5.5cm (5.79" × 4.61" × 2.16"). It is typically used in general applications, troubleshooting, maintenance, education and vocational training, production line testing, radio and TV services, working standards, research design & develop, physics laboratory work.
-
product
Oil Tangent Delta Tester
MG-I
Chongqing Kailian Yongrun Industrial Co.,Ltd.
It is designed to test dielectric loss factor(tangent delta tgδ) and capacitance of transformer oil, capacitor oil, cable oil and other insulation oils.
-
product
Decade Capacitance Box
1412-BC
The wide capacitance range and high resolution of the GenRad 1412-BC decade capacitance box make it exceptionally useful in both laboratory and test shop. Owing to its fine adjustment of capacitance, it is a convenient variable capacitor to use with an Impedance Comparator. The polystyrene dielectric used in the decade steps is necessary for applications requiring low dielectric absorption and constancy of both capacitance and dissipation factor with frequency.
