Filter Results By:
Products
Applications
Manufacturers
Coaxial Cable
-
product
Coaxial Cable Drivers & Amplifiers
B-1020
*Wideband: DC to over 30MHz*Maximum Output: to 10V PK, 20V PK-PK*Maximum Input: ±5V to ±200V PK-PK as required. Also to 900kV PK with Ross Voltage Divider*Signal Isolation: 500,000 Ohm 450V PK*Input Impedance: Up to 2 Megohms*Load Impedance: 50 Ohm or greater*Power Source: AC or Optional Battery*Will drive over 500 Feet of Coaxial Cable
-
product
Coaxial Cable Tester
6106
Peaceful Thriving Enterprise Co Ltd
This device is designed to test the connection of F type coaxial cable. The testing includes continuity and cable mapping. The tester includes 4 mapping terminals with different color and a F type adapter, which are very helpful for cable identification.
-
product
Low PIM Coaxial Cable Assemblies
For applications that demand low VSWR, low insertion and low PIM cable assemblies; RFI now offers semi-rigid and corrugated cable assemblies with factory soldered N and DIN connectors. Assembled using the latest soldering equipment for years of performance reliability. Each assembly is tested for insertion loss, VSWR and PIM rating and is shipped with individual test data. Available using flexible or super flexible corrugated cables with a standard or fire retardant jacket.
-
product
Dual, Low Noise, Coaxial Cable Optimized
DCOAX
Very high precision, three-terminal capacitance measurements can be affected by the self-inductance of the test cables, mainly at higher capacitance values. Magnetically induced noise can also reduce the quality of measurements. The cable now offered by Andeen-Hagerling both minimizes these problems and provides a way to standardize the residual self-inductance.
-
product
Coaxial Cable Termination Toolkit
ICFP
Ardent’s ICFP is a next generation coaxial cable termination toolkit for advanced system design de-embedding, de-bugging, and calibration. Designed for the lowest loss access to signal paths on an IC circuit footprint, this solution is a simple, cost effective alternative to expensive probers and x-y tables for Engineers who need to probe multiple signals at once.
-
product
Cables
Cables connect test and measurement devices to other NI and third-party hardware accessories or to individual header pins. They range from multipurpose coaxial cables to device-specific cables, all with industry-standard connector types to fit your system.
-
product
LCD Multifunction Cable Tester
MT-7059
Display test result on large LCD for easy reading and cable status identificationThe wire can be tracked directly in connection with Ethernet service, router, and PC terminalValidate and troubleshoot wiring on RJ11/RJ45 cables, Coaxial cable, USB cable, IEEE 1394 cableTest cable status for continuity, shorts, opens,miswired, crossover9 different tones selection for convenience use under different environment conditionAll installation and maintenance fields of telecommunication, networking, cable TV and more
-
product
SMB Female to BNC Female Cable, 50 Ohm, 61 cm (Quantity 8)
778415-01
The SMB-BNC Coaxial Cable, sometimes referred to as SMB-100 or SMB-110, connects measurement and signal devices. NI offers this 50 Ω cable in different lengths and quantities.
-
product
Microwave Wideband Direct Modulated DFB Transmitters
MT52 (40KHz~20GHz)
Hangzhou Huatai Optic Tech. Co., Ltd.
MT52 series microwave wideband direct modulated DFB transmitter, are able to transmit 20G microwave RF signal with long distance, wide bandwidth, and flat responsibility. They provide an outstanding linearity fiber optical communication for analogue and digital wideband microwave application. Due to avoidance of using expensive coaxial cable or wave guide, there will be no limitation in transmission distance, which improves the signal quality and reliability of the microwave communication. They can be widely applied in microwave communication system such as remote wireless; timing and reference signal distribution, telemetry, measurement and delay line etc.
-
product
LAN Cable Tester
21-6566-00
The Handheld Lan Cable Tester is an intelligent continuity tester for LAN cables, Phone cable and Coaxial cable. Open, short and misswiring are also tested. It provides the installers an ease of use which keeps you from wasting time through complex menus
-
product
Adapter/Stainless Steel
WADP-NFSM-01
Warison provides wide range of wireless passive coaxial components, includes Adapters, Attenuators, Coaxial Cables Assemblies, DC Blocks, Filters, Isolators & Circulators, Probes & Terminations. With outstanding capability of development and design, Warison is able to custom the spec based on customer��s demand. All Warison��s products pass inspection and electronic performance test before shipping out. It is our principal to deliver the best solution to all our clients.
-
product
Adapter/Stainless Steel
WADP-24M24F
Warison provides wide range of wireless passive coaxial components, includes Adapters, Attenuators, Coaxial Cables Assemblies, DC Blocks, Filters, Isolators & Circulators, Probes & Terminations. With outstanding capability of development and design, Warison is able to custom the spec based on customer��s demand. All Warison��s products pass inspection and electronic performance test before shipping out. It is our principal to deliver the best solution to all our clients.
-
product
LANTRACKER
PH-100/120
The Lantracker is a network tester, pin-by-pin cable tester, and tone generator all in one. As a network tester, it detects whether a network is active or inactive and displays network speed (10/100/1000 Mbps) in either case. It also flashes the network hub or NIC’s port light corresponding to the cable it is connected to, to show the cable’s port number. As a cable tester, it performs loop-back or remote tests of network, data, voice, and coaxial cables, displaying the results on a pin-by-pin LED display which moves from pin to pin automatically or manually. The Lantracker can be used to test cable or shield integrity, testing network function and speed, and tracing cable using its tone generator function (tone probe not included). Includes an adaptor for testing coaxial-F cable. Uses 1 9V battery.
-
product
EOC Mater
EOCM-7101
Hangzhou Softel Optic Co., Ltd.
*EOCM-7101 is the outdoor EOC Master of the EOC (Ethernet Over Coaxial) solution. It is in compliant with HomePlug AV standard.*The EOCM-7101 have one EOC module. It provide one TV input, one com output and two 10/100/1000M auto-negotiation uplink ports.*It offers the high-speed data service to the customer based on the coaxial cable network.
-
product
Cable Tester, Coax Cable Mapper 8 ID Finder with Toner
TCT-128
A handheld testing device designed for CATV and security installers to test multi-run coaxial cable systems terminated with "F" or BNC connectors. Uses eight color coded ID finders to locate and identify cables.
-
product
Adapter/Stainless Steel
WADP-NFNF-01
Warison provides wide range of wireless passive coaxial components, includes Adapters, Attenuators, Coaxial Cables Assemblies, DC Blocks, Filters, Isolators & Circulators, Probes & Terminations. With outstanding capability of development and design, Warison is able to custom the spec based on customer��s demand. All Warison��s products pass inspection and electronic performance test before shipping out. It is our principal to deliver the best solution to all our clients.
-
product
IRIG-B TTL TO RS485 Converter
SPC - INS - 1010
Signals & Systems India Private Limited
The IRIG-B TTL signal is a time synchronization protocol that can be transmitted up to 50m maximum using coaxial cable. So the relay which is to be received the IRIG-B TTL signal may be far away from the IRIG-B source. The relay may be not able to synchronize with the GPS. To avoid such an incident in the field, some of the relays have provision to receive IRIG-B RS485 signal. The IRIG-B RS485 signal can able travel up to 1200m without any booster. All Time source equipment may not be supplied with IRIG-B RS485 signal output. The converter will act as a bridge between GPS Time source and Relays for time synchronization.
-
product
Adapter/Stainless Steel
WADP-24M29F
Warison provides wide range of wireless passive coaxial components, includes Adapters, Attenuators, Coaxial Cables Assemblies, DC Blocks, Filters, Isolators & Circulators, Probes & Terminations. With outstanding capability of development and design, Warison is able to custom the spec based on customer��s demand. All Warison��s products pass inspection and electronic performance test before shipping out. It is our principal to deliver the best solution to all our clients.
-
product
Wattchman RF Station Monitor/Alarm Systems
81090
The Coaxial Dynamics Wattchman Monitor/Alarm measures forward and reflected RF power simultaneously in 50-Ohm coaxial cables and transmission lines. It is compatible with our entire series of 7/8" through 6-1/8" Line Sections and will accept plug-in elements that range from 5 watts to 100 kW full scale from 0.45 MHz to 2300 MHz.
-
product
InfiniBand to BNC Cable, AI0-7 for PXIe-4492
787916-01
16-Pin K-Type Male InfiniBand to 8 1-Pin BNC Male, 50 Ohm Coaxial Cable - The SHB4X-8BNC is a coaxial cable that connects data acquisition and control devices.
-
product
Capacitive Divider
It can be chosen as PD sensor for Techimp PDCheck, PDScope or PDBaseII systems. It is suitable for on line or off line PD tests onrotating machines, for both spot measurements and monitoring applications. A BNC termination is available to connect the coupler through a coaxial cable.
-
product
RGB Video Driver
PCI900
The PCI900 is a PCIe form factor module that has dual RGB analog video receiver inputs. It outputs two analog RGBs that provide the capability to drive UXGA video up to 110 feet over coaxial cable. The input impedance is 75 ohms with a signal level of 1 VPPper RS-343A with sync on green. The output characteristic being 1 VPP into 75 ohms per RS-343A which can drive a minimum of 110 feet of cable.The PCI900 receives only power from the PCIe bus and has no other connection to the PCIe bus.
-
product
signal analyzer
DSA DOCSIS
Only the highest signal quality ensures maximum throughput. The R&S®DSA DOCSIS signal analyzer has been designed to support users by ensuring the highest signal quality. DOCSIS is the standard for transmitting IP data within hybrid fiber coaxial (HFC) cable TV networks.
-
product
Analog Transmission
A pair of AHD (Analog HD) CCTV video signal transmisson units, it can send AHD video and DC power through one coaxial cable simulaneously. The distance between Sender and Viewer can be up to 800 meters.
-
product
High-performance LPDA
ALP690
The ALP690 is a high-performance LPDA (log periodic dipole array) antenna with a bypassable, built-in RF amplifier for use with wireless microphone receivers in location or studio production. The design delivers +4 dBd of passive gain in a directional pattern to extend operating range, and, when DC power is applied, the amplifier applies gain to overcome loss in long coaxial cable runs. By offering both active and passive operation modes, the ALP690 can be used as a receiver antenna (active or passive) and as a transmitter antenna (passive only).
-
product
Flexible Cable Assembly
WCBA-WC0129M.29M1
Warison provides wide range of wireless passive coaxial components, includes Adapters, Attenuators, Coaxial Cables Assemblies, DC Blocks, Filters, Isolators & Circulators, Probes & Terminations. With outstanding capability of development and design, Warison is able to custom the spec based on customer��s demand. All Warison��s products pass inspection and electronic performance test before shipping out. It is our principal to deliver the best solution to all our clients.
-
product
Microwave Wideband Externally Modulated Transmitters (without RF Amp)
MT80 (30KHz~40GHz)
Hangzhou Huatai Optic Tech. Co., Ltd.
MT80 series microwave optical transmitter, adopts external modulation technique, are able to transmit 40GHz microwave RF signal with long distance, wide bandwidth, and flat responsibility. They provide an outstanding linearity fiber optical communication for analogue and digital wideband microwave application. Due to avoidance of using expensive coaxial cable or wave guide, there will be no limitation in transmission distance, which improves the signal quality and reliability of the microwave communication. They can be widely applied in microwave communication system such as remote wireless; timing and reference signal distribution, telemetry, measurement and delay line etc as well as 10Gb/s and 40Gb/s high speed communication system. MT80 adopts low noise, narrow linewidth CW DFB laser as light source; LiNbO3 external modulator as signal modulation, no laser chirp, low dispersion distortion, high extinction ratio, Full-transparency operation mode. It can be applied in long distance and extra-long distance transmission after EDFA.
-
product
Adapter/Nickel
WADP-NMSM
Warison provides wide range of wireless passive coaxial components, includes Adapters, Attenuators, Coaxial Cables Assemblies, DC Blocks, Filters, Isolators & Circulators, Probes & Terminations. With outstanding capability of development and design, Warison is able to custom the spec based on customer��s demand. All Warison��s products pass inspection and electronic performance test before shipping out. It is our principal to deliver the best solution to all our clients.
-
product
Adapter/Stainless Steel
WADP-24F29F
Warison provides wide range of wireless passive coaxial components, includes Adapters, Attenuators, Coaxial Cables Assemblies, DC Blocks, Filters, Isolators & Circulators, Probes & Terminations. With outstanding capability of development and design, Warison is able to custom the spec based on customer��s demand. All Warison��s products pass inspection and electronic performance test before shipping out. It is our principal to deliver the best solution to all our clients.
-
product
2 Pack InfiniBand to BNC Cables, AI0-7 and AI8-15, 0.2m, for 449x
780040-01
16-Pin K-Type Male InfiniBand to 8 1-Pin BNC Male, 50 Ohm Coaxial Cable - The SHB4X-8BNC is a coaxial cable that connects data acquisition and control devices.
