Filter Results By:
Products
Applications
Manufacturers
Combustion
-
product
Combustible Trip Amplifier Module
TA102A
The TA102A is a single-channel Combustible Gas Trip Amplifier Module designed for use with one General Monitors intelligent transmitter to monitor combustible gases and vapors within the lower explosive limit (LEL) and provide status indication and alarm outputs. Microprocessor-based electronics allow all options to be user selectable through a front panel interface (mode / select switch and digital display).
-
product
Fixed Digital Gas Detector
OLCT 10N
Teledyne Gas & Flame Detection
The OLCT 10N is a digital combustible gas detector designed for to detect combustible, toxic gases or oxygen. Intended for use in combination with the MX 16, MX 32 and MX 43 controller, the OLCT 10N provides a fast and accurate response.All transmitter information is received by the controller in less than 1 second.Non-intrusive operator interface requires only a simple magnetic wand and allows one man calibration without opening the enclosure.
-
product
Test and Check Advanced Kit w/ DL479/ CD100A/ EM152/ PDT550
TACK20
UEi Test & Measurement Instruments
Convenient Advanced Test and Check Kit, includes True RMS Clamp meter, Combustible leak detector, Dual input manometer, NSF waterproof thermometer, K-Type pipe clamp adapter, K-Type Input jack adapter, Carrying case
-
product
Laser Induced Incandescence (LII)
Soot is considered a hazardous pollutant emission and is typically a result of incomplete combustion processes, and thus is also related to combustion performance. Laser Induced Incandescence (LII) is a laser-optical measurement technique dedicated to soot diagnostics. LII can provide measurements of soot volume fraction, such as in Diesel engine exhaust, and even instantaneous images of soot distribution during formation inside a running IC engine.
-
product
Combustion
Our combustion gas analysers are compatible with a wide range of machines, such as engines, industrial boilers, incinerators and industrial furnaces. They can be used to assess various combustion parameters, from efficiency and yield to CO, O, NOx and other gas concentrations in flue and exhaust gases.
-
product
SUGGESTED REPLACEMENT/UPGRADE C165+*
C165
UEi Test & Measurement Instruments
The C165 Combustion Analyzer with EOS Technology and High Altitude Compensation eliminates the number one hassle experienced by HVAC contractors, the cost and down time of replacing the O2 sensor. The EOS technology for combustion analysis replaces the everyday electro-chemical O2 sensor with the EOS technology CO2 sensor lowering the cost of ownership and includes High Altitude Compensation
-
product
Gas Monitor
Ultima® XIR
The microprocessor-based, infrared Ultima XIR gas detector is precisely engineered to continuously monitor for combustible gases and vapors. The unit features DuraSource Technology, which offers improved IR life, and a HART port for easy output access.
-
product
Domestic Direct Reading Spectrometer
CS-8610
Wuxi Jinyibo Instrument Technology Co., Ltd.
1. Convenient, practical and reliable: unique combustion device, equipped with infrared detection system, direct connection, remote control operation.2 , patented burner design (using utility model patent technology)The burner electrode upgrading system adopts a spring structure, the electrode adjustment is convenient, and the double sealing ring guarantee the pressure balance in the furnace cavity without tempering.3 , to ensure accurate measurement results◆Using low-noise, high-sensitivity, high-stability pyroelectric infrared detectors.◆Specially-made new platinum infrared light source, continuous heating and high spectral efficiency.The modular design of the whole machine, the electronic circuit is highly integrated, which improves the reliability of the instrument.◆Industrial-grade integrated linear module power supply, stable output, no fault.◆The infrared detection part and the combustion furnace are connected by optical fiber, and cooperate with multi-level concealed isolation circuit to completely eliminate arc interference.◆Double filter device to reduce the impact of dust on the analysis results.4 , electronic balance is not quantitative sample: you can choose different brands of electronic balance, automatic online, to achieve non-quantitative weighing.
-
product
Oxygen Logger Sensor
NUL-205
This sensor can be used to make measurements of the level of free oxygen in air or dissolved oxygen in water. The free oxygen in air mode is used to measure changes in oxygen levels during combustion or in reactions that produce oxygen (hydrogen peroxide decomposition). The dissolved and free oxygen modes are very useful in the study of photosynthesis.
-
product
Pressure Manometer
This product is widely used in measuring fan pressure,wind speed,oven pressure,and hydraulic system. This product can also be used in controlling the gas ratio in combustion and valve control and monitoring the blood pressure and breath pressure with other medical devices
-
product
High Speed Gated Imaging and Spectroscopy Cameras
PI-MAX 4®
Teledyne Princeton Instruments
The PI-MAX 4® improves time-resolved imaging and spectroscopy with either intensified CCD (ICCD) or intensified EMICCD (emICCD) systems. With a wide range of applications, such as plasma diagnostics, combustion and quantum computing, there is no other ICCD that can match the performance and flexibility of the PI-MAX 4 .
-
product
Combustible and Toxic Gas Detection
IMR IX616
IMR Environmental Equipment, Inc.
It has a high-quality sensor, and uses natural diffusion as the method for detection. It has high sensitivity and reproducibility. It also uses an embedded MCU controller and is easy to operate. The shell has special high strength anti-slip rubber it is water-proof, explosion-proof and dust-proof. It has alarms that are visual, audible, and with vibration.
-
product
Test and Check Kit w/ DL469/ CD100A/ EM152/ PDT550
TACK10
UEi Test & Measurement Instruments
Convenient Test and Check Kit, for quick testing, includes True RMS Clamp meter, Combustible leak detector, Dual input manometer, NSF waterproof thermommeter, Carrying case
-
product
Isoperibol Calorimeter
AC500
The AC500 determines calorific value, a key indicator of quality and value in solid and liquid fuels, through measurement of the heat released after combustion of a sample. This stand-alone benchtop unit uses a fully-integrated circulation system for a compact footprint—no additional heaters or coolers required. An integral water-measuring station simplifies sample preparation, and a Windows®-based operating system uses an electronic thermometer accurate to 0.0001°C to measure temperature every six seconds. Two-channel correction is possible through constant temperature monitoring in both the outer jacket and the calorimeter proper.
-
product
Gas Monitor System
Henan Bosean Electronic CO.,Ltd.
Used to detect combustible, flammable and toxic gases, and oxygen depletion.
-
product
Flame Ionization Detector
A flame ionization detector converts a hydrocarbon gas concentration into an electrical signal. The flame is hydrogen fueled and burns in hydrocarbon free combustion air. Either side of the flame are two electrodes between which an electric field is generated by means of a polarization voltage. The sample is pre-mixed with the fuel gas and heated in the flame to a temperature at which the hydrocarbon molecules ‘crack’ and CH fragments appear. These CH fragments are oxidated by the oxygen in the combustion air resulting in the formation of CHO+ ions. The ion current then passes to the electrodes and the resulting current measured is proportional to the quantity of C atoms derived from organic compounds.The Thermo-FID features two separate microprocessor controlled pressure compensations to avoid any influence from environmental or sample conditions. In addition, the complete Thermo-FID range of analyzers are equipped with a flame trap that is used as a heated sample inlet filter. The measurement chamber and all material in contact with the sample gas are heated between 120°C and 200°C to avoid condensation.
-
product
Infrared Gas Detector
SMC 5100-28-IT
The SMC 5100-28-IT detector uses infrared technology, an accurate and stable gas detection method that is low maintenance and can operate in highly combustible and/or low oxygen environments.
-
product
Multi-Stage Injection Analyzer
FJ-8000 series
Common rail method already is commonly known as an injection system of diesel engine now. That system enables multi-stage fuel injection by offering high injection pressure in various driving situation. Adopting the common rail system helps improving fuel consumption, reducing noise and vibration, because the system can make the fuel approximate complete combustion which suppresses PM and NOx generation. FJ-8000 series is the multi-stage injection analyzer that supports more accurate injection by measuring injection quantity, injection rate, injection timing, and injection period by multi-stage injection of common rail system in the environment that is near to an actual vehicle environment.
-
product
Gas Monitor
TG5000
The TG5000 Gas Monitor is an effective and economical solution to detecting combustible and toxic gases, as well as oxygen deficiency/enrichment, in wastewater, commercial and light industrial applications. The TG5000 helps personnel to work safely in these environments offering a variety of sensor and configuration options.
-
product
Combustion Flue Gas Analyzer
712
Combustion Efficiency Analyzer. Combustible Gas Detector. CO Analyzer. Differential Thermometer. Differential Digital Manometer. Data Logging and PC Interface with Optional IRDA Adapter
-
product
CGS500 Combustible Gas Sensor
The Monicon CGS500 thermocatalytic combustible gas sensor has been designed to measure concentrations of combustible gases in the range 0-100% LEL. The CGS500 is fitted in an EExe certified junction box.
-
product
Flue Gas Analyzer (Instrument Only)
C160
UEi Test & Measurement Instruments
Backed by UEi Service+ to give up to 6 years’ warranty, next day recertification, and a reduced cost of ownership. The C160 Residential Combustion Analyzer is instrument only, easy to use with a rugged design, multiple sensor protections and altitude compensation. Essential information for installing and maintaining furnaces and boilers all in one device.
-
-
product
High Performance Isotope analysis of LC Separated Compounds
Iso CHROM® LC
Elementar Analysensysteme GmbH
Unlike the existing LC-inlet solution via chemical oxidation, the iso CHROM LC works with high-temperature combustion. It quantitatively converts organic carbon to CO2.In addition, the easy-to-use iso CHROM LC shows outstanding precision, accuracy, and linearity without significant peak broadening that can diminish the chromatographic performance. In continuous operation, virtually all peaks in a chromatogram can be analyzed for the stable isotope ratios of carbon.
-
product
Residential/Commercial Combustion Analyzer Kit for Oil-Fired Appliances /Printer
C165+OILKIT
UEi Test & Measurement Instruments
Backed by UEi Service+ to give up to 6 years’ warranty, next day recertification, and a reduced cost of ownership. The C165+ Residential/Commercial Combustion Analyzer is easy to use with a rugged design, multiple sensor protections, altitude compensation and differential pressure. Prints to optional printer and wireless App. The new LINK feature connects the included wireless pipe clamp temperature probes and other optional probes to the C165+. Essential information for installing and maintaining furnaces and boilers all in one device.
-
product
RH850 Family (Automotive only)
RH850/E2x
RH850/E2x microcontrollers are ideal for powertrain applications, have high operation processing performance for realizing new combustion systems for fuel-efficient engines, and built-in hardware for knock control such as a successive approximation A/D converter, delta-sigma A/D converter, cyclic A/D converter, Digital Filter Engine (DFE), and Advanced Timer Unit (ATU-V), and engine control such as fuel injection control.
-
product
High CO & NOX Analyzer
715
Combustion Efficiency Analyzer. NO & NOX Analyzer. CO Analyzer(calculates CO2). Differential Thermometer
-
product
Residential Combustion Analyzer w/ Printer Kit
C162
UEi Test & Measurement Instruments
The C162, with EOS Technology, eliminates the number one hassle experienced by HVAC technicians, the cost and down time of replacing the O2 sensor. The EOS award-winning technology for combustion analysis replaces the everyday electro-optical sensor with EOS CO2 technology, lowering the cost of ownership. The C162 offers direct CO2 measurement and features a 30 second start up time.
-
product
Long Neck Combustible Gas Leak Detector
CD100A
UEi Test & Measurement Instruments
The CD100A is the service persons tool designed to detect combustible gas leaks in residential and small commercial applications. Semiconductor sensor responds instantaneously to all combustible gases. The easily adjusted, steady tic rate provides a precise indication of the leak source. The CD100A can be used in tight quarters where others might not fit.
-
product
PCIe Gen3 Full HD, High Speed, Compact Camera for
CB019MG-LX-X8G3
Full HD, High speed, compact, fast camera for: Vehicle Impact, Airbag Deployment and Safety Restraints Testing, Digital Image Correlation (DIC), Projectile, Explosives, Ballistics, Combustion and Missile Launch Tracking, Fluid and Flow Visualization, Sports Broadcasting, Commercial Film, Television and Studio Production, Fluidics and Particle Image Velocimetry (PIV), Flat panel inspection (FPD), printed circuit board (PCB) examination and more.
