Filter Results By:
Products
Applications
Manufacturers
Couplers
enable a signal to be used in another circuit.
-
product
R.F. Coupler and high Pass Filter
7415-3
There are those who disagree with the r.f. conducted susceptibility test setup of Method CS02 of MIL-STD-462. Homemade rigs have sprouted to comply with the coupling capacitor requirement, each with it own disadvantage. Our little Type 7415-3 R.F. Coupler is the answer. A neat little box with BNC connectors and a pair of binding posts, it is rated at 270 V.A.C. at the LINE terminals and 20 volts PMS into the GEN port. Looks good and does a fine job.
-
product
Diesel Compression Tester
34700
Measures cylinder pressure on diesels equipped cars and trucks. Records maximum pressure reached during engine test. Release valve allows for immediate venting and resets gage for repeat tests. Swivel end quick coupler is connected to adapters sold separately. High pressure hose is 16 1/2" long. Gage is scaled from 0-1,000 PSI and 0-70 BAR.
-
product
Directional Coupler
DCZ-XXE/Y
The DCZ-XXE/Y directional couplers are used for extracting or introducing RF power flow in a transmission line withoutdistortion of signal characteristics. The directional couplers are available in 3, 6, 10, 15, 20 dB coupling values and30 - 35 dB minimum directivities*. 4-ports directional couplers are available in bi-directional (BDC4-XXE/Y) and dual-directional(DDC4-XXE/Y) configurations.
-
product
Directional Coupler
RF directionalcouplers coupler both coupler and style packages coupler various frequencies and power levels.
-
product
3 DB 90 Degree Hybrid Couplers
KRYTAR's 90 Degree Hybrid Couplers perform many functions, including splitting and combining signals in amplifiers, switching circuits, and antenna beam-forming networks used in a wide range of commercial and military applications. 90 degree hybrids are used in circuits requiring a balanced division of power into two transmission lines with 90 degree separation of phase.
-
product
90 Degree Hybrid Couplers To 600 MHz
This category of hybrid dividers features designs from 5 to 600 MHz with 2:1 to 4:1 bandwidth. Maximum insertion loss of 0.5 dB is specified for most units. These 90-degree hybrids are designed for a power rating of 1 watt maximum for a load VSWR of 1.2:1 or better. For use in 50-ohm environments.Pulsar Microwave currently offers this product line in three space-saving packages. The connectorized outline 412 comes standard with SMA female connectors. Outline C is a surface mount package useful for handheld applications with limited PCB area. Outline 301 is hermetically sealed for rugged environments.
-
product
Single connector for a HG cable, and two HM connectors
MVNA-8-350-2
The lower part of the Central Unit model MP-8-350-2 has a single connector for a HG cable, and two HM connectors (Fig. 9). Two Harmonic Mixers can work simultaneously, for instance HM2 detecting transmission through the DUT, and HM1, at port 3 of a directional coupler, detecting reflection from the DUT.
-
product
Inductive Coupler
CLAMPMITTER™
The CLAMPMITTER™ is a unique tool for inductive coupling. This self-contained inductive transmitter increases productivity, promotes safety and simplifies locates by condensing the transmitter and inductive coupler into one cordless package. Whether climbing down a manhole or accessing a utility box, the Clampmitter is an easy alternative to suiting up with a full transmitter and wired coupler.
-
product
10-16 DB Directional Couplers From 0.5 To 50 GHz
Single directional couplers within this series operate from 0.5 MHz to 50 GHz and are available in standard values of 10, 13 and 16 dB. They fulfill narrow and broadband requirements with coupling tolerances of +/- 1 to 1.25 dB. These couplers are optimized for best matching and high directivity with flat coupling response.
-
product
Couplers, Repeaters, Bus Switches, Connectors, Cables & More
Accessories for the MIL-STD-1553 data bus are as much of an interface as the communication card. Therefore at Excalibur we provide a full line of accessories for the MIL-STD-1553 data bus that include, Box/Inline Couplers, Repeaters, Bus Switches, break out boxes, connectors, terminators, transformers and custom cable assemblies. Excalibur uses only premier quality parts from known manufacturers. We constantly test our products to meet our higher standards.If you have a need for an accessory product for your card and it is not listed please contact us to see if it is a product we should be supporting.
-
product
Telecom Fiber Couplers
Thorlabs offers a varied selection of single mode (SM) and polarization-maintaining (PM) fiber couplers, as well as single mode 1x8 and 1x16 PLC waveguide splitters that have center wavelengths at common telecom wavelengths, including 850 nm, 1310 nm, and 1550 nm.
-
product
3 DB 180 Degree Hybrid Couplers
KRYTAR's 180 Degree Hybrid Couplers offer wide frequency coverage in single, compact packages which provide low insertion loss, high directivity and tight coupling. These hybrid couplers offer simple solutions in many applications within those frequency bands including electronic warfare (EW), commercial wireless, SATCOM, radar, signal monitoring and measurement, antenna beam forming, and EMC testing environments. For many space-restricted situations the compact size of these KRYTAR couplers are ideal. These couplers can be also be manufactured to meet military specifications.
-
product
IPM Drive
IPM drive photocouplers (optocouplers) are optically coupled isolators containing a GaAlAs LED on the input side and a photo diode and signal processing circuit on the output side in a single chip. This coupler is a high common mode transient immunity (CMR), high CTR type whose pulse width changes according to the operating temperature, making it ideal for driving IPMs (intelligent power modules).
-
product
3x3 1x1 2x2 1x2 Couplers
Couplers can be used to split light from one or more fibers onto two or three fibers or to combine light from two or three fibers onto one or more fibers.
-
product
High Power Single And Dual Directional Couplers
Pulsar Microwave manufactures a line of single and dual directional couplers specifically designed for high power operation. There are various narrow and broadband designs from 0.1 MHz to 10 GHz. These directional couplers come in standard values of 30, 35, 40 and 50 dB with coupling tolerance of +/- 1 dB.The high power directional couplers have low insertion loss. Coupling flatness is maintained at +/- 1 dB or less among models. Most units hold a mainline VSWR of 1.2:1 or better throughout the operating frequency range. Pulsar Microwave has designs up to 2.5 kW input power. Typical directivity is 20 dB or more.Standard outlines are available with SMA or N type female connectors. For higher power ratings, typically the mainline will use N connectors with SMA on the coupled ports.
-
product
Voltage Input Module For Remote I/O
The Voltage Input Module for Remote I/O features 2-, 3-, and 4-wire spring terminal connection methods, a built-in power supply for sensors, four selectable input ranges, and simultaneous sampling. A remote I/O system consists of an EtherCAT bus coupler and individual modules mounted on a DIN rail. You control the Voltage Input Module for Remote I/O from a real-time controller, such as a CompactRIO Controller or an Industrial Controller. You can use remote I/O hardware to add low-cost I/O for simple tasks while your controller handles advanced tasks such as image processing, motion control, and high-speed or specialty measurements.
-
product
Conducted Immunity Test System
Conducted RF immunity tests acc. to IEC/EN61000-4-6 and BCI tests acc. to ISO 11452-4 and MIL-STD 461 CS 114 Signal generator,RF-power amplifier, RF-power meter and directional coupler (optional) in one 19”-caseStand-alone operation possible with optional available netbookControl-software includedMost important parameters are shown on an integrated displayAutomatic EUT-monitoringOperation via USB port of a PC or NotebookComplete range of CDNs available
-
product
Octocouplers
Panasonic Industrial Devices Sales Company of America
Panasonic's PhotoIC Coupler is a high performance optocoupler which consists of LED in input circuit, and custom IC in output circuits. PhotoIC Couplers are commonly used for high speed communication requiring physical isolation in various equipment and devices.
-
product
High-Speed CMOS Output
High-speed CMOS output photocouplers (optocouplers) are optically coupled isolators containing a GaAlAs LED on the input side and a CMOS output IC on the output side. This coupler is a high common mode transient immunity (CMR), high-speed CMOS output type device designed for high-speed logic interface circuits.
-
product
PD Coupler
Techimp Capacitive PD Couplers offer both the PD and sync signals references, allowing a thorough investigation of the signal originating inside the asset they are connected to.Techimp Couplers are individually tested according to the following international standards: IEC60358; IEC60694; IEC60270.
-
product
Passive Component Integration
Integrate passive optical components of your choice such as WDM couplers, splitters, band-pass filters, PM beamsplitters and circulators. PXIe and benchtop models support SMF, MMF and PMF.
-
product
Immunity Testing Systems
CIS Series
The CIS series test systems are configured to perform conducted immunity testing according to IEC 61000-4-6. The system includes an ACS series power amplifier, coupling/decoupling Network (CDN), directional coupler, 150Ω to 50Ω adapters, power attenuators, cables and [optional] CSAT software. These systems, when properly configured, are capable of testing your products to all levels given in IEC 61000-4-6 up to 230 MHz. You can choose from three systems. Follow the links below for detailed information, including a comprehensive datasheet listing system specs.
-
product
30 DB Directional Couplers From 0.5 To 40 GHz
Pulsar Microwave's CS30 series single directional couplers operate at narrow and wideband frequencies within 500 MHz to 40 GHz. They have a nominal coupling value of 30 dB, with tolerances of +/- 1 to 1.25 dB. These directional couplers are rated at 50 watts maximum input power. These couplers are optimized for best matching and high directivity with flat coupling response. They come standard with SMA or N female connectors.
-
product
Taps And Passives
ATX offers the latest innovations in passives for HFC networks, including taps, couplers, splitters and power inserters. The 2GHz XS Series enables MSOs to support DOCSIS® 4.0 architectures, while the 1.2GHz SG Series will maintain a 1.2GHz plant and offers compatibility with Cisco’s popular Surge-Gap portfolio of hardline taps and passives. A bonus feature with the ATX 2GHz taps and passives is the upgradeable faceplate, futureproofing these HFC devices for 3GHz and beyond.
-
product
90 Degree Hybrid Couplers To 26.5 GHz
Pulsar Microwave manufactures hybrid couplers and dividers from 400 MHz to 26.5 GHz for use in 50-ohm systems. These hybrids are available in narrowband and wideband designs with up to 20:1 bandwidth ratios. Most models are built to handle 100 watts input power. The designs are stripline, and optimized for best matching and isolation performance. Available with SMA or N type female connectors.
-
product
Cylinder Leakage Tester Kit
CLT200
Quickly locates internal engine problems such as bad rings, valves and leaking head gaskets. Dual 2-1/2" heavy duty gauges with protective outer boots. Scales read 0-100psi and 0-700 kg/cm2Pressure regulated manifold includes high quality quick couplers for fast set-ups.
-
product
PCI Express to VME Interface
SIS1100-E2/3104-2
The SIS1100-e2/SIS3104-2 interface/bus coupler is the choice for demanding VME readout applications. VME block tranfser speeds up to 160 MByte/s are readily accomplished in conjunction with state of the art VME slave hardware.
-
product
Digital Output
VME-2170A
The VME-2170A optically coupled digital output board consists of VMEbus compatibility logic,data control logic, four 8-bit output registers, and 32 optically isolated high-level outputs. The board is implemented as a double Eurocard form factor PC board, and provides all necessary address decoding and data transfer control logic to accept both 8- and 16-bit data transfers. Optical couplers isolate the 32 outputs from each other and from the VMEbus.
-
product
Dual-Directional Couplers
KRYTAR’s directional couplers are uniquely designed for systems applications where external leveling, precise monitoring, signal mixing or swept transmission and reflection measurements are required. These couplers provide simple solutions for many applications including electronic warfare (EW), commercial wireless, SATCOM, radar, signal monitoring and measurement, antenna beam forming, and EMC testing environments. For many space-restricted applications the compact size makes KRYTAR directional couplers ideal solutions.
-
product
RF Directional Couplers
Directional Couplers from the leading manufacturers are listed below. Use the filters to narrow down on products based on your requirement. Download Datasheets, Compare products and Request Quotations. Your Inquiry will be directed to the manufacturer and their distributors who will get back to you with a quote.
