Filter Results By:
Products
Applications
Manufacturers
-
product
MBE Sources
Dopant
For precise control of fluxes for MBE dopant constituents, or for gases that do not require thermal cracking, Veeco's Dopant products are ideal.
-
product
TDR Structural Health Monitoring
Material Sensing & Instrumentation
MSI Time-Domain-Reflectometry (TDR) Structural-Health Monitoring probes the structural health of a composite part by propagating a fast electrical pulse along a distributed linear sensor which has been fabricated directly in the laminate. The sensor is formed from the native graphite fibers already used in composite manufacture, and constitutes zero defect. Fibers are patterned into a microwave waveguide geometry, or transmission line, and interrogated by a rapid pulse as shown below. Structural faults along the line cause distortions in waveguide geometry, producing reflected pulses similar to radar. Cracking, delamination, disbonds, moisture penetration, marcelling, and strain are all detected by propagation delay, for sensor lengths up to several meters.
-
product
Flame Ionization Detector
A flame ionization detector converts a hydrocarbon gas concentration into an electrical signal. The flame is hydrogen fueled and burns in hydrocarbon free combustion air. Either side of the flame are two electrodes between which an electric field is generated by means of a polarization voltage. The sample is pre-mixed with the fuel gas and heated in the flame to a temperature at which the hydrocarbon molecules ‘crack’ and CH fragments appear. These CH fragments are oxidated by the oxygen in the combustion air resulting in the formation of CHO+ ions. The ion current then passes to the electrodes and the resulting current measured is proportional to the quantity of C atoms derived from organic compounds.The Thermo-FID features two separate microprocessor controlled pressure compensations to avoid any influence from environmental or sample conditions. In addition, the complete Thermo-FID range of analyzers are equipped with a flame trap that is used as a heated sample inlet filter. The measurement chamber and all material in contact with the sample gas are heated between 120°C and 200°C to avoid condensation.
-
product
Visual Fault Locators
*Visual Fault Locator, we can understand its function in the letter. It could be regarded to be part of OTDR and the fiber fault locator is cheap.*Fiber visual fault locator is a kind of device which is able to locate the breakpoint, bending or cracking of the fiber glass. It can also locate the fault of OTDR dead zone and make fiber identification from one end to the other end. Designed with a FC,SC,ST universal adapter, this fiber testing red light is used without any other type of additional adapters, it can locates fault up to 10km in fiber cable, with compact in size, light in weight, red laser output.*Fiber visual fault locators include the pen type, the handheld type and portable visual fiber fault locator. Fiberinthebox also supply a new kind of Fiber laser tester/ optical fiber pen/ fiber laser pen, it can locates fault up to 30km in fiber cable.*Welcome to our store. Contact us at sales@fiberinthebox.com or Live Chat with us. Save your money & time right now! Buy from optical fiber supplies at Fiberinthebox.com with your confidence.
-
product
Cupping Tester
PCE-CPT 20
PCE-CPT 20 is a cupping tester, or coating flexibility tester, used for testing the adhesion, elongation and deformability of paints, lacquers, varnishes, powder coatings and other surface coatings on metal sheets. Used in manufacturing production, paint shop and quality control applications, the PCE-CPT 20 cupping tester aids in determining coating strength, durability and elasticity. A mandatory test in Qualicoat and QIB accredited quality control laboratories, a cupping test, also referred to as an Erichsen test or dent test, uses a spherical punch to deform a sample. This deformation results in a cup-like bulge. When using the PCE-CPT 20 to perform a cupping test in accordance with the ISO 1520 standard, the sample should be placed coating side up so that the 20 mm spherical punch presses against the uncoated underside of the metal sheet. The cupping test is terminated when small cracks and/or detachments are observed on the bulged part of the sample. The PCE-CPT 20 cupping tester's easy-to-read display shows the bulge deformation distances that can be used to determine the coating's flexibility rating.
-
product
Thickness and Flaw Inspection
MultiScan MS5800
Eddy current testing is a noncontact method used to inspect nonferromagnetic tubing. This technique is suitable for detecting and sizing metal discontinuities such as corrosion, erosion, wear, pitting, baffle cuts, wall loss, and cracks in nonferrous materials.
-
product
Ozone Test Chamber
EKT-2001OZ-HPSSX
Designed and manufactured in accordance with ASTM D1149, ISO1431 & JIS K6259 standards. Providing precise and accurate ozone (OZ) concentration environment for rubber and polymer test. Widely applied to (1) Accelerated ageing research (2) Quality control and assurance tests and (3) R&D laboratory formula experiments for cracking resistance.
-
product
Pentype Visual Fault Locator
RA3105
Radiasun International Group Ltd.
The RA3105 Pentype VFL is specially designed for field personnel who need an efficient and economical tool for fiber tracing, fiber routing and continuity checking in optical network. It includes: Finding the breakpoint, poor connections, bending or cracking in fiber optic cables. Finding the faults of OTDR dead zone End-to-end visual fiber identification.
-
product
Fiber Visual Fault Locator
Fiber visual fault locator is a pen type device which is able to locate the breakpoint, bending or cracking of the fiber glass,this small fiber optic equipment can locate the fault of OTDR dead zone and make fiber iIdentification from one end to the other end .
-
product
Crack Width Ruler
The range also includes gauges used for the measurement of crack width in concrete and other structures.
-
product
Crack Width Ruler
143
Elcometer 143 Crack Width Ruler is a simple gauge that has been designed to provide inspectors with a low cost alternative to a graduated microscope for determining the width of a crack in concrete or other building materials.
-
product
Conformal Coating Inspection (CI AOI)
They cover the components, the area around the components and identify most coating issues including cracks, bubbles, insufficient / excess coating, loss of adhesion and other common contaminations. Full coverage inspection for conformal coating.
-
product
Manual Cartridge Dispensers
2K 50mL
Featuring a compact design, these versatile dispensers accept all ratios and eliminate cartridge cracking. Our durable two-component 50mL manual dispensers are lightweight and well balanced, making them easy to position and hold steady.
-
product
Roughness Testers
Roughness is an important parameter when trying to find out whether a surface is suitable for a certain purpose. Rough surfaces often wear out more quickly than smoother surfaces. Rougher surfaces are normally more vulnerable to corrosion and cracks, but they can also aid in adhesion. A roughness tester is used to quickly and accurately determine the surface texture or surface roughness of a material. A roughness tester shows the measured roughness depth (Rz) as well as the mean roughness value (Ra) in micrometers or microns (µm). Measuring the roughness of a surface involves applying a roughness filter. Different international standards and surface texture or surface finish specifications recommend the use of different roughness filters. For example, a Gaussian filter often is recommended in ISO standards.
-
product
Ultra-sonic Test System
V-Meter
The V-Meter is an advanced ultrasonic, pulse-velocity test system widely used for quality control and evaluation of concrete structures. It can identify non-homogeneous conditions such as voids, cracks, honeycombs and frozen concrete.
-
product
Flaw Detectors
Flaw detectors are essential for ensuring the safety and quality of industrial products. They accurately identify defects such as cracks, voids, and inclusions without damaging the materials. Ultrasonic testing is particularly notable for its precision and versatility among the various non-destructive testing methods.
-
product
Moisture Meters
Moisture can be found in any material. Even materials considered to be dry have a minor amount of moisture. An imbalance of moisture, whether it be excessive moisture or too little moisture, can cause problems ranging from undesired mold and bacteria growth to cracks and defects. To avoid a moisture imbalance, it is essential to monitor moisture content with a moisture meter that returns accurate and reliable measuring results. A moisture meter can measure the moisture content of everything from the air (relative humidity) to construction and building materials (concrete, wood) to biomass and agricultural products (hay, straw, grain, corn, beans, pellets) to solid waste (pulp, slurry) and beyond. Many moisture meter devices can also measure temperature. The moisture measurement range of each moisture meter varies depending on the model. Some moisture meter products take moisture measurements, store the moisture measurement data to an internal memory or SD cad, and allow the stored moisture measurement data to be transferred to a computer for detailed analysis by means of an evaluation software. PCE Instruments' moisture meter products come factory calibrated. ISO calibration certificates are available optionally for purchase as accessories to most moisture meter models. An ISO calibration certificate may be important to your company in meeting specific quality standards.
-
product
Non-destructive Asphalt Density Testing Equipment
PaveScan RDM
Geophysical Survey Systems, Inc.
The PaveScan RDM is ideal for uncovering inconsistencies that occur during the paving process, including poor uniformity and significant variations in density. By detecting these problems, PaveScan RDM helps to avoid premature failures such as road raveling, cracking and deterioration along joints.
-
product
Crack Detectors
GAOTek offers a large selection of crack detectors which are affordable, easy to operate and user-friendly. For some industries such as aviation, civil, infrastructure and space technology, even the slightest crack can lead to risks of hazards. There have been cases in the past where projects costing billions were destroyed in seconds due to a minute crack on the surface of the body. GAOTek provides trustworthy devices with various features that are helpful in detecting the smallest crack on an object.
-
product
Concrete Investigations
The first signs of cracking and rust staining can serve as an early warning that deterioration of a reinforced concrete structure is about to take hold, However, these signs are not always in evidence requiring specialist knowledge coupled with appropriate technology to identify if the structure is suffering deterioration, albeit in the early stages.
-
product
Ozone Aging Test Chambers
Dongguan Amade Instruments Technology Co., Ltd
Ozone aging test chamber is also called as ozone climate simulator or ozone aging tester. It is one of climatic testing instruments, which is to simulate and intensify the ozone condition for determining the cracking resistance of vulcanized or thermoplastic rubbers when subjected to dynamic or static tensile strain exposed at a man-made constant temperature to atmosphere containing given concentration of ozone in conformance with relevant specification. Ozone test is an indispensable method for people to research effects and mechanisms of ozone on rubbers, quick identify and evaluate anti-aging performance of rubbers and find solutions for improvement of quality and lifespan.
-
product
Video Endoscope Cameras
PeakTech Prüf- und Messtechnik GmbH
Is used to locate objects such as connection terminals, electronic components, break points, constrictions, cracks or components at hard-to-reach, hidden locations. This video endoscope camera offers a variety of excellent technical properties, such as the detachable monitor connected by video cable or the high-resolution camera with 6 dimmable LEDs for lighting, which can take photos and videos.
-
product
Automatic Type Cupping Testing Machine
GWB-60C
Jinan Testing Equipment IE Corporation
The digital cupping tester is mainly used in the test of metal sheets and thin strips. The automatic cupping testing machine can test the plastic deformation performance of the sheets and thin strips. The automatic cupping testing machine meets the requirement of international GB/T 4156-2007 "Metal Material Sheet and Thin Strip Erichsen Cupping Test". Adopting a hydraulic clamping and hydraulic stamping composite oil cylinder, the cupping tester automatically shuts down when a test sample has crack, so as to facilitate the observation of crack. With peak value memorizing function, the cupping tester can automatically memorize the maximal stamping force and the maximal deformation depth. A turning type clamp ensures the convenient replacement, assembling and disassembling of a punch and a test sample.
-
product
Non-Destructive Testing
Piezoelectric ceramic materials are the active component in nondestructive testing transducers. The material is driven with an ac signal to generate an ultrasonic sound wave that is coupled into an object. The ultrasonic wave is reflected back to the transducer when it encounters a change in density in the material caused by a crack, porosity, or other object with a different density.
-
product
Non Destructive Testing (NDT)
NDT covers a wide group of testing techniques used to evaluate the properties of a material, part, product, weld or system without causing damage. NDT carried out at KLL includes:Liquid Penetrant Testing (LPT) is used for the detection of surface breaking discontinuities on magnetic and non-magnetic metallic materials.Fluorescent and colour contrast penetrants are available to be used in the following methods:-Water washableSolvent removablePost emulsifiableMagnetic Particle Inspection (MT/MPI) is used for the detection of surface breaking and slightly sub-surface (up to 2mm) discontinuities.Bench type crack detectors and portable units are employed producing various waveforms (i.e. A.C, HWDC and induced magnetic flow) to give both circular and longitudinal magnetism.On-site testing is carried out using electro magnetic yokes and permanent magnets producing induced magnetic flow.Ultrasonic Flaw Detection (UT), also known as Ultrasonic Inspection, is used for the detection of volumetric discontinuities in ferrous and non-ferrous products (forgings and castings etc.), and welds in magnetic and non-magnetic materials.UT is capable of penetrating metals, dependent on the material characteristics, up to 10m in length.Some thickness and depth checks can also be carried out using ultrasound.Radiography services are available through sub-contract booked in advance. Notice is required for on-site work.Personnel are available at short notice for in-house or on-site work in the UK and overseas.All inspectors undertaking non destructive testing (LPT, MT/MPI and UT) are qualified to, and meet a minimum of, PCN Level 2.PCN Level 3 supervision is available in-house for LPT, MT/MPI, UT offering consultancy services including procedure writing and commentary, auditing of techniques and Level 3 Supervisor cover.We can assist clients in product qualification, material testing, quality assurance and audit programmes.
-
product
Outsole Belt Flexing Tester
UI-FT36
Outsole Belt Flexing Tester, which is also named as Bata Belt Flex Tester, is used to test sole flexing resistance ability. Belt Flex Tester is designed and applicable to SATRA TM133 Resistance to crack initiation and growth–belt flex method.
-
product
Ozone Test Chamber
EKT-2001OZ-HCSTX
Designed and manufactured in accordance with ASTM D1149, ISO1431 & JIS K6259 standards. Providing precise and accurate ozone (OZ) concentration environment for rubber and polymer test. Widely applied to (1) Accelerated ageing research (2) Quality control and assurance tests and (3) R&D laboratory formula experiments for cracking resistance.
-
product
X Ray Flaw Detector
A non-destructive testing (NDT) device used to inspect materials for internal flaws or defects such as cracks, voids, inclusions, and weld discontinuities.
-
product
AOI Handlings System
The AOI handling system is a compact facility with various test units. Via an ionization cleaning station the ceramics are transferred to the contacting station. There, the resistance values of the substrates are tested with a rigid needle adapter. Afterward, the ceramics are further conveyed to the three (optionally four) AOI test stations (for automatic optical inspection) and are tested for cracks, unevenness, faulty imprints, contamination, etc. The poorly evaluated ceramics arrive at a review station where the operator can assess and evaluate the errors on the monitor. If the operator is uncertain about a fault, the ceramic in question can be positioned under the microscope position and inspected by eye. Poorly defined ceramics are marked accordingly with an ink pen.
-
product
Variable Impact Tester
1615
The Elcometer 1615 Variable Impact Tester is a simple to use gauge ideal for evaluating the resistance of a coating to impact (elongation, cracking or peeling).
