Filter Results By:
Products
Applications
Manufacturers
Current Probes
measure AC or AC-DC amperage without contacting conductors.
See Also: Current Sensors
-
product
T3RC Rogowski Coil Current Probes
T3RC Series
Teledyne Test Tools Rogowski Current probes offer a broad range of products covering a wide frequency span and current measurement ranges for maximum application coverage whilst being easy to use in difficult to reach parts of the circuit.
-
product
Current Probes
Current probes allow you to measure DC or AC current. Yokogawa's selection of current probes allow measurements ranges up to 500 ARMS and bandwidths up to 100MHz.
-
-
product
T3CP Series AC/DC Current Probes
T3CP Series
Teledyne Test Tools AC/DC Current Probes are powered by an external universal power supply and work with any Oscilloscope with a high-impedance BNC input. The range of five current probes includes models with bandwidths up to 100 MHz, peak currents up to 500A and sensitivities to 1 mA/div.
-
-
product
Godzilla High Current Probes, 150 Amp
HC500
Current Rating (Amps): 150Average Probe Resistance (mOhm): 25Test Center (mil): For more details, please contact us.Test Center (mm): For more details, please contact us.Full Travel (mil): 260Full Travel (mm): 6.60Recommended Travel (mil): 250Recommended Travel (mm): 6.35Overall Length (mil): 3,215Overall Length (mm): 81.66
-
product
Eddy Current Probes and Drivers
Proximity sensors work on the eddy current principle. A proximity system consists of an eddy current probe, extension cable and driver. A high-frequency RF signal is generated by the driver, sent through the extension and probe cables and radiated from the probe tip. The tip consists of a precision wound copper coil inside a chemical and temperature resistant PEEK case.
-
product
High Current Probes
The maximum continuous current rating of a spring probe is determined by its design, size, and construction. Typical probes are rated from 2 to 8 amps maximum continuously current at working travel. While this is sufficient for most board test applications, higher current applications will require a much more solid and rugged probe to withstand current capabilities of 10 to 150 amps and beyond.Another high current solution is our feed-through plunger probe line. As the name already describes, the plunger moves right through the probe and is made from a single piece, reducing the internal resistance of the probe to a minimum.
-
-
product
Micsig AC & DC Current Probes
CP2100
Shenzhen Micsig Instruments Co., Ltd.
*Split design, small and exquisite appearance, easy to test *Compatible with all BNC-connected oscilloscopes, adapters can also work with multimeters.
-
product
CC15010X, 10 MHz, 150 A Current Oscilloscope Probe
786849-01
The CC15010X, or Hioki 3274, is a clamp-on current probe that offers a wide DC to 10 MHz bandwidth and 150 A of continuous input. It is ideal for capturing transient current signals from switching power supplies, inverters, and motor controllers. The probe requires an external power supply.
-
product
Complete Power Analysis System
PK3564-PRO+
PK3564-PRO+ complete Power Analysis System includes PS3550 Power Analyzer, AC charger, Quick-Start manual, deluxe voltage leads, four eFX6000 flexible current probes, SD memory card, PSM-A Software, Mini Line-to-DC Converter, Bluetooth Adapter, USB Communications Cable, CASW Weather-Resistant Carrying/Operating Case, and 2-year deluxe warranty.
-
product
Current Probe
PA-677
*Max. 70ADC/140Ap-p*Sensitivity: ≧2mA*Bandwidth: DC~1MHz*Rise Time: 0.35μS*Over Range Function*50mV/A, 500mV/A Range*Adaptor/Battery Input*Separating Design,Convenient Durable
-
product
Current Probe With Hall Effect Technology
CP 35
The CP 35 current probe has been designed for use with oscilloscopes respectively for accurate, non-intrusive measurement of AC, DC and complex waveform currents.
-
product
AC / DC Current Probe, 100 MHz, 30 Arms
N2783B
The N2783B current probe is an accurate and reliable solution for measuring AC and DC currents. Using a hybrid technology that includes a Hall effect sensor and an AC current transformer, the probe provides accurate measurement of DC or AC currents up to 30 Arms continuous.
-
product
Positional Current Probe, PCB Track Touch And Measure
I-prober 520
Current measurement from insulated probing of conductorSuitable for observation and measurement of current in PCB tracks, component leads and ground planesWide dynamic range of 10mA to 20A peak to peakWide bandwidth of DC to 5MHzLow noise figure equivalent to <6mA rms at full B/WSafety rated to 300V Cat II (600V Cat 1)Suitable for connection to any oscilloscopeHigh accuracy general purpose H-field probeConverts to 'closed magnetic circuit' current probe
-
product
30A, 50MHz High Sensitivity Current Probe
CP030A
Teledyne LeCroy current probes are available in a variety of models for a wide range of applications. The full range of Teledyne LeCroy current probes includes models with bandwidths up to 100 MHz, peak currents up to 700 A and sensitivities to 1 mA/div. Teledyne LeCroy current probes are often used in applications such as the design and test of switching power supplies, motor drives, electric vehicles, and uninterruptible power supplies.
-
product
Non-contact Sheet Resistance/resistivity Measurement Instrument With PC
NC-10 (NC-20)
*Easy operation and data processing by PC*No damage measurement by non-contact eddy current method*Replaceable probes by meas. range (*Second or more probe is for the option)*1 point measurement of center position*5 types of model for each measuring range*Temperature correction for silicon wafer function
-
product
CC05120X, 120 MHz, 5 Arms Current Oscilloscope Probe
786847-01
The CC05120X, or Hioki CT6701, is a clamp-on current probe that offers a wide DC to 120 MHz bandwidth and 5 Arms of continuous input. It is ideal for capturing transient current signals from switching power supplies, inverters, and motor controllers. The probe requires an external power supply.
-
product
AC Current Probes
CWT
Power Electronic Measurments Ltd
The CWT Rogowski current probe is suitable for measuring AC currents ranging from 300 milliamps to hundreds of kA from below 0.1Hz to >30MHz.
-
product
Broadband Current Probes
Conducted currents can be measured without making direct contact with the source conductor or metallic surface by means of clamp-on broadband current probes. The BCP-5xx EMC Current Probes are designed to permit field intensity meters, spectrum analyzers, and other 50W impedance instruments to measure quantitative magnitudes of current.
-
product
Scanning Electron Microscope
SEM
Delivers the world's best resolution with the incorporation of the newly-developed, super-high resolution Gentle Beam (GBSH). In addition, the maximum probe current of the In-lens Schottky Plus gun has been increased from 200 nA to 500 nA.
-
product
Clamp Meter
Shenzhen Graigar Technology Co.,Ltd.
A clamp meter is an electrical tester that combines a basic digital multimeter with a current sensor. Clamps measure current. Probes measure voltage.
-
product
AC / DC Current Probe, 2 MHz, 500 Arms
N2780B
The N2780B current probe is an accurate and reliable solution for measuring AC and DC currents. Using a hybrid technology that includes a Hall effect sensor and an AC current transformer, the probe provides accurate measurement of DC or AC currents up to 500 Arms continuous.
-
product
Current Probe
PA-659
*Maximum Current Value: +/- 150ADC, 100A RMS*1mA = 5mA, 50mA (switchable)*Rising Time: 0.7uS*Bandwidth: DC ~ 500kHz*Over Range Indicator*Battery, AC Power Supply Adaptor (free), dual usages
-
product
500A, 5 MHz CURRENT PROBE, BNC, AC/DC, 500A rms, 750A Peak Pulse
T3CP500-5
500A, 5 MHz CURRENT PROBE, BNC, AC/DC, 500A rms, 750A Peak Pulse.
-
product
Fixed Aperture RF Current Monitoring Probe
TBCP1-200
The TBCP1-200 is a fixed aperture RF current monitoring probe.The probe has a 3dB bandwidth of approximately 200 MHz. The aperture of the RF current monitoring probe is 25 mm. Its transfer impedance is > 14 dB Ohm in the range from 40 kHz to 200 MHz.
-
product
High Current Probes for EV Battery Packs
Up to 500Amps - customized connections - battery pack charging.
-
product
30 Amps, 50 MHz BW Current Probe - AC/DC , 50 Amp Peak Pulse
CP030
Teledyne LeCroy current probes are available in a variety of models for a wide range of applications. The full range of Teledyne LeCroy current probes includes models with bandwidths up to 100 MHz, peak currents up to 700 A and sensitivities to 1 mA/div. Teledyne LeCroy current probes are often used in applications such as the design and test of switching power supplies, motor drives, electric vehicles, and uninterruptible power supplies.
-
product
Wafer Probers
Full Automatic Wafer Prober. Semi Automatic Wafer Prober. High Current Probe Block. 6-inch Manual Prober. 8-inch Manual Prober. 12-inch Manual Prober.
