Filter Results By:
Products
Applications
Manufacturers
DWDM
Dense Wavelength Division Multiplexing
-
product
100GHz Single Fiber Bi-Direction Dense WDM
DWDM-1200
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai DWDM-1204, DWDM-1208 dense DWDM DWDM, which is based on mature thin film filtering technology, It has the feature of low insertion loss, high isolation and flexible channel configuration. It can bi-direction transmit 4 channel(1204) or 8 channel(1208) on one fiber up stream/down stream.
-
product
Passive Modules
Choose from a range of multiplexer and demultiplexer modules supporting both CWDM and state-of-the-art DWDM applications.
-
product
C-Band DWDM Line Amplifier EDFA (WLA-C)
HWA4200 (With SNMP)
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai HWA4200 series, is designed for C-Band 44 waves or 88 waves DWDM system design Line Amplifier gain flatness. Products using the most excellent optical performance, the most advanced electronic control technology and comprehensive software features, has a wide operating wavelength range, Low noise, excellent gain flatness characteristics and transient characteristics.
-
product
(125×150×20mm) C-Band DWDM Booster EDFA Module
WBA4100-FM05
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai WBA4100-FM04 series used 125 x 150 x 20mm MSA standard , is a digital control circuit of DWDM power amplifier function module. Products using the most excellent optical properties, electronic control technology and complete software function is most advanced, wide wavelength range, low noise, excellent gain flatness characteristics and transient characteristics. Application for C-Band 44 wave or the 88 wave of DWDM system.
-
product
Clock and Data Recovery/Retiming
Analog Devices provides single rate, multiple rate, and continuous tuning clock and data recovery (CDR) ICs for metro, long haul, DWDM, FSO, instrumentation, and other applications. Our any rate CDR ICs allow easy integration into protocol agnostic applications, automatically locking onto incoming data streams at any rate, from 10 Mbps to 2.7 Gbps or from 6.5 Mbps to 11.3 Gbps, without the aid of a reference clock while reporting the acquired data rate over the I2C interface. With a proprietary dual loop design, our any rate CDR ICs feature fast locking with superior jitter performance.
-
product
Optical Channel Monitor
Optoplex Optical channel monitor (OCM) uses proprietary thin-film interference filter technology combined with a micro-actuator and high-speed electronics. Optical channel monitor is used to measure critical information data on optical transmission signals in DWDM networks for monitoring signal dynamics, determining system functionality, identifying performance change, and providing feedback for controling network elements so as to optimize operational performance. In particular, Optoplex Optical channel monitor can automatically scan the C-, L- or C+L-band wavelength range and precisely measure channel wavelength, power, and optical signal-to-noise ratio (OSNR). See the following schematic diagram for OCM working principle.
-
product
C-Band DWDM VGA without Mid-Stage Access Next-Generation Variable Gain EDFA
HWA4500 (With SNMP)
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai HWA4500 series is a next-generation variable gain EDFA, which with the most excellent performance and most completes functions in the market. It adopts nowadays most excellent optical performance, most advanced electronic technology and most complete software functions. Remarkable transient suppression control technology and heat management control technology let many complicated optical functions achieved. It is the most versatile multifunction optical amplifier in the market.
-
product
C-Band / L-Band MWDM
WD1615/C, WD1516/L
Hangzhou Huatai Optic Tech. Co., Ltd.
WD1615/C, WD1516/L WDM is based on mature thin film filtering tech, with wide bandwidth, flatness, low insertion loss and high isolation. It is mainly applied to EDFA and DWDM network to achieve the combination and separation of C-Band and L-Band.
-
product
Erbium Doped Fiber Amplifier
EDFA
EDFAs are based on the light amplification in erbium-doped fiber, which are optically pumped by means of 980 nm or 1480 nm light sources. In this way, the light of a larger wavelength within the C or L band applied to the input of the amplifier is amplified, thus widening the range of optical communication links. EDFAs typically operate in saturation and the average signal power determines the average gain. The dynamics of EDFA are unaffected by the sequence and dynamics of a digital signal or channel interaction in DWDM systems. As a result, multiple channels can be bundled within the total erbium spectral amplification bandwidth. However, the total average output power in both cases is determined by the saturation power of the specific EDFA.
-
product
100GHz DWDM Optical Add/Drop Multiplexer (CATV Overlay Multiplexer)
OADM-1001-VOA (100GHz)
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai OADM-1001-VOA is an optical Add-Drop multiplexer with 100GHz channel interval. It is based on mature thin film filter technology, sealed with metal shell, and featured with low insertion loss, high isolation, wide channel and flexible configuration. It is the ideal device to Add(insertion Add)/Drop(Tape-out Drop) a specific wavelength(OADM) in optical fiber DWDM system. OADM-1001-VOA configures a manual-adjust optical attenuation, for adjust the equilibrium the optical power between insert channel and main signal channel, which is conveniently used for VOD overlay in CATV system.
-
product
(70×90×15mm) C-Band DWDM FGA Full Function Module Fixed Gain EDFA Module
FGA4400-FM02
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai FGA4400-FM02 series is a fixed gain Full Functional EDFA module which is specifically designed for C-Band DWDM optic transmission system, accord with various communication technology requirements of 44 channels DWDM system. It adopts nowadays excellent optical performance, advanced electronic control technology and complete software functionalities. Excellent total integration electronic transient control technology ensures amplifier to achieve the locking of optimal flat gain (OFG) in large dynamic input optical power range.
-
product
Desktop Tunable Laser Source
GM8042
The GM8042 desktop tunable laser sources offer superior performance in testing DWDMcomponents, AWG & PLC components, optical amplifiers, DWDM system and performing other general-purpose fiber optical test and measurement applications. It is a high wavelength accuracy, high power output, compact dimensions, fast startup, and affordable tunable laser source system. UC INSTRUMENTS provides C band, L band, or C+L band tunable laser sources options.
-
product
Compact & Robust Tunable Laser
WSL-110
Designed for use in fiber optic transmission testing, our WSL-110 can also be used for DWDM component evaluation and coherent communications testing. The WSL-110 features grid tuning and gridless tuning options, allowing any wavelength to be accessed.
-
product
L-Band Separate Raman Fiber Amplifier
RFA6000
Hangzhou Huatai Optic Tech. Co., Ltd.
1. Erbium-doped Fiber Amplifier, due to the multiple cascades and the accumulation of noise caused by spontaneous emission, will reduce the system CNR greatly and thus it will limit the transmission capacity and distance of the system. Raman Fiber Amplifier (RFA) is a newly designed fiber amplifier based on Stimulated Raman Scattering (SRS) effect. It is considered as the core technology of new generation DWDM fiber over-long communication. Compared with Erbium-Doped Fiber Amplifier, Raman amplifier has the advantage of low Noise Figure (NF), wider gain bandwidth, flexible gain spectral region and stable temperature. It is the only device that can operate in 1300~1600 nm.
-
product
(125×150×20mm) C-Band DWDM FGA Full Function Module Fixed Gain EDFA Module
FGA4400-FM05
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai FGA4400-FM05 series is a fixed gain Full Functional EDFA module which is specifically designed for C-Band DWDM optic transmission system, accord with various communication technology requirements of 44 channels DWDM system. It adopts nowadays excellent optical performance, advanced electronic control technology and complete software functionalities. Excellent total integration electronic transient control technology ensures amplifier to achieve the locking of optimal flat gain (OFG) in large dynamic input optical power range.
-
product
C & L-Band Separate Raman Fiber Amplifier
RFA7000
Hangzhou Huatai Optic Tech. Co., Ltd.
1. Erbium-doped Fiber Amplifier, due to the multiple cascades and the accumulation of noise caused by spontaneous emission, will reduce the system CNR greatly and thus it will limit the transmission capacity and distance of the system. Raman Fiber Amplifier (RFA) is a newly designed fiber amplifier based on Stimulated Raman Scattering (SRS) effect. It is considered as the core technology of new generation DWDM fiber over-long communication. Compared with Erbium-Doped Fiber Amplifier, Raman amplifier has the advantage of low Noise Figure (NF), wider gain bandwidth, flexible gain spectral region and stable temperature. It is the only device that can operate in 1300~1600 nm.
-
product
Optical Wavelength Meters
Optical wavelength meter that uses a He-Ne laser as reference wavelength and employs the Michelson interferometer method, providing high-accuracy measurement. It can measure emission center frequencies of LDs for DWDM with high resolution and accuracy.The 8471 even provides a high sampling rate of 10 times per second, and is suitable for oscillation wavelength adjustment. In addition, its deviation display function allows wavelength variation to be measured with high resolution and accuracy.
-
product
C-Band DWDM Booster EDFA (WBA-C)
HWA4100 (With SNMP)
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai HWA4100 series, is designed for C-Band 44 waves or 88 waves DWDM system design power fiber amplifier gain flatness. Products using the most excellent optical performance, the most advanced electronic control technology and comprehensive software features, has a wide operating wavelength range, low noise and excellent gain flatness characteristics.
-
product
Optical Wavelength Meter
Optoplex Optical wavelength meter (OWM) uses proprietary thin-film interference filter in conjunction with Fabry-Perot cavity technology combined with a micro-actuator and high-speed electronics. Its working principle is schematically shown below. By comparison with Optical channel monitor / Optical performance monitor, the proprietary wavelength reference unit is introduced to ensure high precision wavelength measurements. Optoplex Optical wavelength meter is the only DWDM wavelength meter capable of measuring wavelengths of multi-lasers in DWDM networks over C-band and L-band wavelength range with a high accuracy better than that the wavelength locker can provide. For example, the device can simultaneously report 80 wavelength values of 80 channels at 50 GHz channel spacing with the wavelength accuracy ± 2 GHz. DPRAM, RS-232, or USB interfaces are available and OWM can be customized to meet specific requirements.
-
product
Band DWDM EDFA
MSA Module C
Amonics now packages one of its most popular product lines, C-band DWDM Erbium-doped Fiber Amplifiers (EDFAs), into standard MSA size. The same reliable, stable and durable EDFAs are thus readily available for system integration of a wider range of applications. The devices provides the usual alarms and status indicators, with an integrated RS232 computer interface for easy control, diagnostic functions and data acquisition. This MSA series will be expanded to cover EDFAs of different specifications in our product range in order to meet the growing demands.
-
product
Optical Performance Monitor
Optoplex Optical performance monitor (OPM) uses proprietary thin-film interference filter technology combined with a micro-actuator and high-speed electronics. Optical performance monitor is used to measure critical information data on optical transmission signals in DWDM networks for monitoring signal dynamics, determining system functionality, identifying performance change, and providing feedback for controlling network elements so as to optimize operational performance. In particular, Optoplex Optical performance monitor can automatically scan the C-, L- or C+L-band wavelength range and precisely measure channel wavelength and power. See the following schematic diagram for OPM working principle.
-
product
100G,200G 1X2 DWDM Device (3Ports)
Flyin optronics’ 100GHz/200GHz 1x2 wavelength multiplexer utilizes thin film coating technology and proprietary design of non-flux metal bonding micro optics packaging to achieve optical add or drop at a ITU wavelength. It provides ITU channel center wavelength, low insertion loss, high channel isolation, wide pass band, low temperature sensitivity and epoxy free optical path . It can be used for wavelength add/drop in telecommunication network system.
-
product
12/24 CH Insertion Loss/Return Loss Automatic Testing System
CA3201
UC INSTRUMENTS CA3201 12/24 CH INSERTION LOSS/RETURN LOSS AUTOMATIC TESTING SYSTEM is special designed for MPO/MTP fiber cable and multi-channel fiber optical devices like PLC device. It also can be easy changed into AWG DWDM devices testing system ifwe change 1310 /1550 nm light source into UC INSTRUMENTS’ tunable laser source.
-
product
Passive Devices
Fiber Splitters, Muxes, CWDM, DWDM, WDM, PON, Fiber Jumpers, Fiber Attenuators.
-
product
DWDM DFB Light Source (42CH)
DWOS-1000
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai DWOS-1000 seires DFB optical source is the DWDM test platform with high capability, high stability and high flexibility. It is consist of the system rack and plug-in function module. The system rack is equipped with high capability RS232 communication interface, high precision parameter display and power supply module. There are 3 types of the function module: DFB Source module, DWDM, EDFA (optional).
-
product
VOA DWDM with EDFA With VOA, EDFA Dense Wavelength Division Multiplexer
DWDA-1000 (100GHz)
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai DWDA-1000 series is integrated by DWDM, VOA and EDFA module in a 1RU or 3D rack. Each channel of DWDM with a high-resolution factor electronic control adjustable optical attenuator will adjust and equilibrium the power. The insertion loss, power loss because of the channel equilibrium of DWDM will be amplified and compensation by the build-in gain flatness EDFA. Compact and simple device structure, thereby reducing the connections between devices to improve the index and reliability of the system. Can be used in DWDM system power equilibrium, optical add and drop multiplexed (OADW) flexible and expediently.
-
product
(70×90×15mm) C-Band DWDM Full Function Pre EDFA Module
WPA4300-FM02
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai Huatai WPA4300-FM02 series with 70 × 90 × 15mm MSA compact package, is a digital control circuit with DWDM full function preamplifier module. Products using the most excellent optical performance, the most advanced electronic control technology and comprehensive software features, has a wide operating wavelength range, low noise, excellent gain flatness characteristics and transient characteristics. Suitable for C-Band 44 or 88 waves DWDM system applications.
-
product
Multi-channel Optical Power Meter For Swept Test System
MPM-210HMPM-211, 212, 213, 215
Our MPM-210H is ideal for IL, WDL and PDL measurement of multi-port optical components including Dense Wavelength Division Multiplexing (DWDM), Arrayed Waveguide Gratings（AWG) , Wavelength Selective Switches (WSS) and more. When combined with our TSL-Series laser equipped with a power monitor output, the MPM-210H allows the user to complete real-time high precision IL measurements.
-
product
C-Band DWDM VGA with Mid-Stage Access Next-Generation Variable Gain EDFA
HWA4700 (With SNMP)
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai HWA4700 series is a next-generation variable gain EDFA, which with the most excellent performance and most completes functions in the market. It adopts nowadays most excellent optical performance, most advanced electronic technology and most complete software functions. Remarkable transient suppression control technology and heat management control technology let many complicated optical functions achieved. It is the most versatile multifunction optical amplifier in the market.
-
product
EDFA Amplifier
A line of Gain Flattening Erbium-Doped Fiber Amplifiers are designed for in-line amplification of DWDM networks. When a standard EDFA is used to amplify multi-channel DWDM signals, the output power level of various channels will vary according to the gain profile of the erbium fiber. This gain variation can be as great as 6 dB in magnitude. The EDFA-GB-R is unique in its dual-stage amplification and internal Gain Flattening Filter (GFF) to compensate the erbium fiber gain variation.
