Filter Results By:
Products
Applications
Manufacturers
Discrete Device
semiconductor typically having one circuit.
-
product
Combination Module: 2 Ch. MIL-STD-1553 & 12 Ch. Discrete I/O
CM8
The CM8 module is a combination of NAI's MIL-STD-1553B module, FTB, and Enhanced Discrete I/O module, DT4. The CM8 offers twelve channels of discrete I/O and two channels of MIL-STD-1553B communications. The twelve discrete I/O channels are programmable as either input (voltage or contact sensing with programmable, on-module pull-up/pull down current sources), or output (current source, sink, or push-pull) up to 500 mA per channel from an applied, external 3-60 VCC source. The discrete I/O channels also provide additional functionality modes such as Pulse Width Modulation (PWM) output mode and Pattern Generator output mode. The two MIL-STD-1553B communications channels feature a dual, redundant, balanced-line, physical layer; a (differential) network interface; time division multiplexing; half-duplex command/response protocol; and up to 31 remote terminals (devices).
-
product
Circbord
8003
VECTOR Electronics and Technology, Inc.
Pad per hole & peripheral ground plane.0.085” Square pads etched around each hole on wiring side.Accommodates any type DIP IC device or discrete component.Single sided board with pads and peripheral GND plane on one side only.Single-sided with no etch and plating on reverse side.
-
product
PXIe-4139 , ±60 V, ±3 A DC, ±10 A Pulsed, 40 W DC, 100 fA Precision System PXI Source Measure Unit
782856-03
PXIe, ±60 V, ±3 A DC, ±10 A Pulsed, 40 W DC, 100 fA Precision System PXI Source Measure Unit - The PXIe-4139 is a high-precision, system source measure unit (SMU) that features 4-quadrant operation and sources up to 40 W of DC power. This module features analog-to-digital converters that help you perform high-precision measurements with a current resolution of 100 fA or high-speed acquisitions up to 1.8 MS/s. The module can maximize stability and measurement accuracy with SourceAdapt technology, which you can use to tune the transient response to match the characteristics of any load. You can use the PXIe-4139 for applications including manufacturing test, board-level test, and lab characterization with devices such as ICs, power management ICs (PMICs), and RFICs and discrete devices including LEDs and optical transceivers.
-
product
Insulated Gate Bipolar Transistors
The Bourns® IGBT discrete BID series combines technology from a MOS gate and a bipolar transistor, creating the right component for high voltage and high current applications. This device uses advanced Trench-Gate Field-Stop technology providing greater control of the dynamic characteristics while resulting in a lower Collector-Emitter Saturation Voltage (VCE(sat)) and fewer switching losses.
-
product
MPI Fully Automatic Probe Systems
MPI Advanced Semiconductor Test
Addressing the RF and High Power communication devices and discrete passive components production test market requirements, MPI introduced the TS2500 200 mm fully automatic probe system series. The system is based on industry leading production equipment from the Photonics Automation Division and incorporates decades of experience in RF and High Power measurement techniques from the MPI’s Advanced Semiconductor Test (AST) Division in combination with other AST products such as RF Probes, related calibration technology, and High Power accessories.
-
product
ARINC 429 PXI Express Test & Simulation Instrument
PXIe-C429
Avionics Interface Technologies
16, 32, or 64 ARINC 429 Channels (up to 32 Tx & 32 Rx) - Programmable Tx channel output amplitude - Programmable High/Low Speed Operation - Eight (8) Discrete I/O (Four (4) inputs, and four (4) outputs) - Concurrent operation of all Tx/Rx Channels at high data rates - Full error injection and detection • Data capture filtering, 100% bus recording, and physical bus replay - Rate-oriented Label Transmission - Label Selective Trigger for Capture/Filtering - IRIG-B time code encoder/decoder with free-wheeling mode - Application Interface supporting C/C++, C# and VB.NET Development - Device driver support: Windows, Linux, LabVIEW Real-Time (others on request) - Compatible with AIT’s Flight Simulyzer GUI Bus Analyzer Software
-
product
Wide Bandgap Transistors
The key for the next essential step towards a more energy-efficient world lies in the use of new materials, such as wide bandgap semiconductors (WBG) which allow for increased power efficiency, smaller size, lighter weight, lower system cost or all of these together. STMicroelectronics offers the broadest product and technology portfolio of silicon carbide (MOSFETs) and gallium-nitride-based (e-mode HEMT) devices, covering bare dies, discretes and modules belonging to the STPOWER family.
-
product
Rad Hard Supervisory
Renesas' radiation hardened supervisory circuits reduce the complexity required to monitor supply voltages in microprocessor systems. These devices significantly improve accuracy and reliability relative to discrete solutions.
-
product
Gaming Platform Based on AMD Ryzen™ Embedded R1000/V1000 Series Supports up to Eight Independent Displays Including 4K UHD
ADi-SA2X-RZ
ADi-SA2X-RZ all-in-one gaming platform features powerful processing and graphics performance for gaming infotainment and retail. Equipped with AMD Ryzen™ Embedded R1000/V1000 Series, the ADi-SA2X-RZ provides compelling graphics performance from a Radeon™ RX Vega Graphics and/or a PCI Express 3.0 x16 discrete graphics card together with multi-display support for up to eight independent monitors. With the powerful processing performance, advanced security functions, smart middleware solutions, and versatile I/O array, the ADi-SA2X-RZ fully satisfies the needs of your gaming application. The ADi-SA2X-RZ is a true application-ready gaming platform providing OEMs with a highly flexible and reliable all-in-one system that offers unparalleled portfolio of services that help developers save time and remain in compliance. The platform is designed to meet the GLI- 11 (Gaming Laboratories International) certification and all major global gaming market compliance requirements. The comprehensive middleware as well as the security and extensive I/O solutions enable developers to easily bridge applications with peripheral devices, sensors, and surrounding solutions up to central monitoring and control systems.
-
product
HS-1760 Flight Rated XMC Network Interface Controller
XMC-1760-NIC-CC
Avionics Interface Technologies
Dual Channel configurations supporting NC/NC, NC/NT, or NT/NT - 75 Ohm single ended copper or 150 Ohm differential - Eight (8) opto-isolated discrete I/O lines - Rear I/O through the P16 connector - Conduction-cooling and/or conformal coating available - x4 PCIe interface to NIC interfaces, with DMA controller for data movement - Designed for extended temperature operations - ANSI Application interface supporting C development - Device driver support: Windows, Linux, & VxWorks (others on request)
-
product
Discrete Device Test System
capability to perform parallel testing of power discrete devices. As the standard specifications of mainframe, 341-TT/P has 1.2kV/20A and 351-TT/P has 2kV/50A capabilities. These systems have 2 testing subsystems, each of which has 4-station capability by multiplexing to 4 handler/prober stations for high volume production testing.
-
product
PXIe-4137, ±200 V, ±1 A DC, ±3 A Pulsed, Up to 40 W DC, 100 fA Precision System PXI Source Measure Unit
783761-02
PXIe, ±200 V, ±1 A DC, ±3 A Pulsed, Up to 40 W DC, 100 fA Precision System PXI Source Measure Unit - The PXIe-4137 is a high-precision, system source measure unit (SMU). It features 4-quadrant operation and sources up to 40 W of DC power and can pulse up to 500 W. Analog-to-digital converter technology helps you perform high-precision measurements with a current resolution of 100 fA or high-speed acquisitions up to 1.8 MS/s. The module also can maximize stability and measurement accuracy with SourceAdapt technology, which you can use to tune the transient response to match the characteristics of any load. The PXIe-4137 is ideal for a broad range of applications including manufacturing test, board-level test, and lab characterization with devices such as ICs, power management ICs (PMICs), and RFICs and discrete devices including LEDs and optical transceivers
-
product
Switch Modules - 16 Single Pole, Form C, Discrete Relays which are Wired & Controlled Individually
JX16/KC
This module has 16 single pole, Form C, discrete relays which are wired and controlled individually. The relays can be externally wired to make any configuration needed. Use as individual A-B relays or use them to drive external relays, solinoids, or any external device. It is available with Type S or M reed relays.
-
product
Component Test and Analysis Laboratories
The Component Test and Analysis team specializes in electronic and mechanical components such as hybrids, connectors, cables, harnesses, passive or discrete components, and digital or linear devices. The test lab has extensive experience in developing test software to electrically and environmentally characterize virtually any integrated circuit, including analog, digital, mixed signal, converters, FPGA and ASICs, as well as experience in developing actual radiation environments for parts testing. The component analysis team offers the analytical expertise and advanced instrumentation to identify root cause explanation for a wide range of component-level failures, as well as the resources to evaluate for possible quality and reliability issues through non-destructive and destructive techniques. With access to a detailed database, the Component Test and Analysis team offers a 25-year history of test and analysis data — a valuable resource for addressing new customer requirements.
-
product
Tactical Grade Inertial Measurement Unit (IMU)
ADIS16490 iSensor
The ADIS16490 iSensor® device is a complete inertial system that includes a triaxial gyroscope and a triaxial accelerometer. Each inertial sensor in the ADIS16490 combines industry-leading iMEMS® technology with signal conditioning that optimizes dynamic performance. The factory calibration characterizes each sensor for sensitivity, bias, alignment, and linear acceleration (gyroscope bias). As a result, each sensor has its own dynamic compensation formulas that provide accurate sensor measurements. The ADIS16490 provides a simple, cost-effective method for integrating accurate, multiaxis inertial sensing into industrial systems, especially when compared with the complexity and investment associated with discrete designs. All necessary motion testing and calibration are part of the production process at the factory, greatly reducing system integration time. Tight orthogonal alignment simplifies inertial frame alignment in navigation systems. The SPI and register structure provide a simple interface for data collection and configuration control.
-
product
Video RF Splitters
Analog Devices acts as a major supplier of video RF splitters and related technology such as CATV line drivers. Our high performance drivers and splitters enable the implementation of the most advanced cable modems and set top boxes on the market. Typical applications for our technology include multituner digital set top boxes, cable splitter modules, multituners/digital cable ready (DCR) televisions, and home gateways where traditional solutions require discrete passive splitter modules with separate fixed gain amplifiers.
-
product
PXI-4132, 100 V, 2 W Precision PXI Source Measure Unit
780558-01
±100 V, 10 pA Precision PXI Source Measure Unit—The PXI-4132 is a programmable, high-precision source measure unit (SMU). It has a single isolated SMU channel that offers a four-quadrant output that incorporates remote (4-wire) sense as well as external guarding. With its high measurement resolution integrated guarding, the PXI-4132 is ideal for high-accuracy leakage measurements on integrated circuits, discrete components, PCBs, and cables. You can also perform high-speed I-V measurements on a variety of components including diodes and organic LEDs using the onboard hardware sequencing engine. In addition, you can synchronize multiple PXI-4132 modules using the PXI backplane to provide high-speed I-V measurements on transistors and more complex devices.
-
product
Software-based Electroacoustic Test System
SoundCheck
The SoundCheck®system from Listen includes everything you need to perform audio measurements on a wide range of devices – the software, the audio interface, other test interfaces and accessories, and test sequences. The system is centered around the SoundCheck software. This powerful package controls and communicates with the measurement hardware, and includes all the stimuli, algorithms and analysis functionality needed to develop and run virtually any electroacoustic or audio electronic test. It is paired with hardware ranging from a simple, all-in one audio test box to sophisticated discrete components for a complete test system. In addition to Listen hardware, a range of 3rd party products and test accessories are fully supported within SoundCheck.
-
product
Power ICs - Smart Load Switches
Combining multiple functions in a single IC, Vishay smart load switches eliminate the need for external circuitry . A simplified GPIO interface allows for power distribution and sequencing of multiple sub-systems. Slew-rate-control devices provide a controlled supply ramp to reduce inrush current, while fault protection and isolation switches increase robustness with reverse current, overtemperature, current limiting, and short circuit protection features. The ICs offer quick output discharge and small footprints, while their integrated design saves PCB space compared to discrete solutions, reduces BOM counts, and lowers manufacturing costs.
-
product
Test Handlers
Cohu has 50+ years of semiconductor test expertise designing and manufacturing pick-and-place, gravity feed, test-in-strip handlers, MEMS test cells, and turret-based test handling and back-end finishing equipment for ICs, LEDs and discrete components.Our test handlers support a variety of package sizes and device types, including automotive, mobile, power, micro-electromechanical systems (MEMS) and microcontrollers, among others.
-
product
PCIe-Mini Card
PCIe-Mini-AVIO-8
The PCIe-Mini-AVIO-8 is an avionic compliance discrete I/O card, it monitors or controls the on/off (high/low) status of up to 8 devices. 8 channels are used as an input and output for the Low side of 500ma drivers.
-
product
MACC - embedded
EXC-8000MACC
The EXC-8000MACC is a table driven translator (data converter - protocol converter) that enables devices supporting different communications specifications (e.g. Ethernet, Serial, ARINC 429, Mil-1553, Discretes etc.) to talk to each other.
-
product
ARINC 429 Test & Simulation Interface for PCI Express
PCIe-C429X
Avionics Interface Technologies
16, 32, or 64 ARINC 429 Channels (up to 32 Tx & 32 Rx) - Programmable Tx channel output amplitude - Programmable High/Low Speed Operation - Eight (8) Discrete I/O (Four (4) inputs, and four (4) outputs) - Concurrent operation of all Tx/Rx Channels at high data rates - Full error injection and detection - Data capture filtering, 100% bus recording, and physical bus replay - Rate-oriented Label Transmission - Label Selective Trigger for Capture/Filtering - IRIG-B time code encoder/decoder with free-wheeling mode - Application Interface supporting C/C++, C# and VB.NET Development - Device driver support: Windows, Linux, LabVIEW Real-Time (others on request) - Compatible with AIT’s Flight Simulyzer GUI Bus Analyzer Software
-
product
Switch Modules - 8 Single Pole, Form C, Discrete Power Relays which are Wired & Controlled Individually
JX8/KCP
This module has 8 single pole, Form C, discrete power relays which are wired and controlled individually. The relays can be externally wired to make any configuration needed. Use as individual A-B relays or use them to drive external relays, solinoids, or any external device. Screw Terminal Connectors and Armature power relay for switching up to 8 Amps of DC or AC current.
-
product
Semiconductor Test System
IST Information Scan Technology, Inc.
As power modules age, their performance degrades. Proper testing and maintenance of semiconductor devices used in power switching can ensure optimal performance and prevent down-time throughout a device’s lifecycle. The IST Model 8900 Series Discrete Semiconductor Test Systems allows you to effectively identify the percent of degradation in semiconductor devices by simulating the exact current and voltage of the parameters used by devices under real operating conditions.
-
product
PXIe-4138, 60 V, 3 A System PXI Source Measure Unit
782856-01
±60 V, 3 A System PXI Source Measure Unit—The PXIe‑4138 system source measure unit (SMU) delivers high power, precision, and speed. It is ideal for a broad range of applications including manufacturing test; board-level test; lab characterization with devices such as integrated circuits (ICs), power management integrated circuits (PMICs), and radio frequency integrated circuits (RFICs); and discrete devices including LEDs and optical transceivers. The PXIe‑4138 features 4-quadrant operation. The PXIe‑4138 is a hardware-timed instrument with a high-speed sequencing engine for synchronizing acquisitions between multiple SMUs. The module supports direct DMA streaming between the host PC and SMU, so you can stream large waveforms and measurement data at the full update rate and sample rate of the instrument.
-
product
PXIe-4139, ±60 V, ±3 A DC, ±10 A Pulsed, 20 W DC, 100 fA Precision System PXI Source Measure Unit
782856-02
PXIe, ±60 V, ±3 A DC, ±10 A Pulsed, 20 W DC, 100 fA Precision System PXI Source Measure Unit - The PXIe-4139 is a high-precision, system source measure unit (SMU) that features 4-quadrant operation and sources up to 20 W of DC power. This module features analog-to-digital … converters that help you perform high-precision measurements with a current resolution of 100 fA or high-speed acquisitions up to 1.8 MS/s. The module can maximize stability and measurement accuracy with SourceAdapt technology, which you can use to tune the transient response to match the characteristics of any load. You can use the PXIe-4139 for applications including manufacturing test, board-level test, and lab characterization with devices such as ICs, power management ICs (PMICs), and RFICs and discrete devices including LEDs and optical transceivers.
-
product
NI-9423, 24 V, 8 Channel (Sinking Input), 1 µs C Series Digital Module
783735-01
24 V, 8 Channel (Sinking Input), 1 µs C Series Digital Module - The NI‑9423 works with industrial logic levels and signals to connect directly to a wide array of industrial switches, transducers, and devices. Each channel is compatible with 24 V logic levels, can accept up to … 30 V discrete logic levels, and has an LED that indicates the status. The NI‑9423 offers isolation between the input and output banks from channel to earth ground. The NI‑9423 is a correlated digital module, so it can perform correlated measurements, triggering, and sychronization when installed in a CompactDAQ chassis.
-
product
Intelligent MCC Controller
MM2
The Motor Manager II (MM2) combines control functions and comprehensive motor protection in one package. This compactdevice provides sophisticated control and protective relaying at significant cost savings over the discrete devices normallyfound in a low voltage motor control center (MCC).
-
product
Ion Beam Etch
Nexus IBE Series
Etch precise, complex features for high-yield production of discrete microelectronic devices and components with the NEXUS® Ion Beam Etch (IBE) Systems.
