Filter Results By:
Products
Applications
Manufacturers
Display
illuminates image signaling.
-
product
Insulation & Multifunction Tester (LCD Display)
1153 AI
Standard Electric Works Co., Ltd
● Microprocessor-controlled.● Automatic voltmeter AC/DC at Start/Reset.● Auto range● Auto off.● Battery test.● Battery test at switch ON/Reset.● Safety voltmeter before each test.● Auto discharge on all test and all ranges.● Leads Auto-Null key.● Test Auto-Stop.● Smart hold & stop on voltmeter ac/dc.● Ener-Save feature to extend battery life.● Continuity short circuit current > 220mA.● Continuity open circuit voltage of 5Vdc.● Nominal voltage @ 1mA on all insulation ranges.● Accept 8 rechargeable batteries or Alkaline of normal.● BS 16 edition.
-
product
Digital Display Spring Tensile & Compression Tester
STC Series
Jinan Testing Equipment IE Corporation
Spring tester is to test the characteristics of spring under tensile and compression mode in allowed capacity. The peak load, real load and displacement can be showed in real time. N, kgf, lbf can be displayed.
-
product
Fibre Linked EHV And Distributed Assets PD Monitoring System
EHV-PDM
The EHV-PDM is a PD monitoring system designed for application on critical EHV and distributed assets, where the monitoring point could be many hundreds of metres or tens of kilometres apart. Fibre linked monitoring points transmit PD data over long distances to the main monitoring unit, which then processes the data and displays the results on a secure customer web front end.
-
product
AS 857 AUTO SWITCHING TRANSMITTER
- Auto Switching to Secondary Input if Primary Signal Fail/Drops below -6dBm- Switches back to Primary Input when Primary Signal Reconnect/Improves above -4dBm- Input Signal Display of Active Input- AGC for both Input
-
product
Digital Multimeters
T3DMM Series
Teledyne Test Tools new T3DMM series are dual display digital desktop multimeters that provide a rich and powerful feature set. The design is easy-to-use from the front-panel and computer-based control via USB or LAN. Each model is equipped with a 4.3 inch TFT-LCD true color screen with 480 * 272 resolution for easy viewing. The T3DMM series also features numerical data display, histograms, trend charts, bar charts and statistics, in addition to the built-in arithmetic functions including Measurement statistics.
-
product
Cable Continuity Detectors
Shenzhen Noyafa Electronic CO.,LTD
NOYAFA Cable Continuity Detector can test the open circuit, short circuit, crossover and continutiy for RJ11/RJ45/BNC/USB cable, and the test result is displayed by the visible LED light status.
-
product
Line Testers
GAOTek provides a large collection of certified and feature-rich line testers for sale to the United States, Canada and Globally. These devices are mainly used for line installation, line performance testing, inspection, and maintenance of the telecommunication networks. They are particularly designed to accelerate telecom trouble shooting and with the help of latest technology they are equipped with a smart CPU, IC, and SMT. These devices have some unique features such as caller ID display and last number redial. Moreover, it can also be used for multi-line testing, wire pair checking, inspection of line insulation and test for breaks and faults.
-
product
Video Signal Generator
MSPG-3235
Analog was a main item in display device industries at the past time, but from now on, the digital is getting developed with multi-function and large-sized resolution like 4Kx2K. Preparing for this change, this signal generator is an essential equipment of LCD, LED, PDP, D-TV, TV, CRT display device industries, which was made for generator analog signal, digital signal, TV signal and D-TV signal, HDCP, code simultaneously and sufficiently examining a large size display device.
-
product
Thermal Imaging Camera
Zhejiang ULIRvisionTechnology Co., LTD
A thermal imaging camera is a device that uses infrared and thermal imaging technology to convert the image of the temperature distribution of the target object into a visible image through detecting the infrared radiation of the target object and applying signal processing and photoelectric conversion. The thermal imaging camera accurately quantifies the actual detected heat and images of the entire object in real-time in the form of a surface, thus accurately identifying the suspected fault area that is heating. The operator initially judges the fever condition and the fault location through the image color and hotspot tracking display function displayed on the screen of the thermal imaging detector, and strictly analyzes it, thereby embodying high efficiency and high accuracy in confirming the problem.
-
product
OBD-II Breakout Box
PPECB
The Power Probe OBD-II Breakout Box is a CAN Bus circuit tester compatible with 12 and 24 Volt systems. The tool connects directly into the Vehicle’s Data Link Connector (DLC) testing for any abnormalities such as shorting and reverse polarity at the pins. If shorting or reverse polarity is present, connecting the PPECB first will prevent harm before connecting a Diagnostic Scan Tool. The Breakout Box provides a live display of present communicating signals without having to use a Digital Multimeter. Additionally, you can quickly test the voltages at all 16 pins.
-
product
DC Ground Fault Locators
We currently offer one highly capable DC ground fault locator for sale to the United States, Canada and Globally. This fault locator is highly reliable and highly capable of locating any ground fault in a variety of settings. This one piece of ground fault locator equipment is all you will ever need to find any fault, in any location, in any system. With advanced computations and fuzzy logic it can very accurately display the insulation level of the tested circuit. We offer the best and only ground fault locator you will ever need. To learn more about his product please click below where you will also be provided key features and the ground fault locator specifications.
-
product
Lead Acid Intelligent Battery Tester
612
This digital battery tester is designed for testing 6V and 12V standby SLA, cyclic GEL and car FLOODED batteries. Simple in operation, the ACT 612 simulates a full 20 hour (C20) discharge test in seconds and displays the DC Voltage results and Ah capacity available.
-
product
SWR/ Power Meters
SX600/SX600N
Frequency range:1.8 to 525MHz/S1(1.8 to 160MHz), S2(140 to 525MHz). Power display range:5W 20W 200W. Accuracy at full scale:±10%. Minimum power at SWR measurement:S1(1W), S2(4W)
-
product
FiberPulse OTDR
XO1
FiberPulse OTDRs send pulses down fiber optic networks from one end of the fiber, displaying a trace and reporting all detected events such as splices, connectors, macrobends and fiber ends and breaks. The total fiber length is reported along with name, location, loss and reflectance of detected events. The intuitive keypad design features integrated shortcut keys designed for quickly positioning and analysing events. Another feature of this unit is the Live Optical Signal Detect Function, which tests if the fiber is live before sending the pulse, this can effectively prevent accidental damage to the OTDR and attached communication equipment.
-
product
SMARC
ROM-5780 B1
Advantech ROM-5780 B1 SMARC 2.1 Computer-on-Module is powered by Rockchip RK3399 SOC which includes dual-core Arm Cortex-A72 and quad-core Arm Cortex-A53 processors and Arm Mali-T860MP4 3D graphics engine. It provides rich display interface: HDMI 4K@60Hz, eDP and LVDS to meet different requirement. It also features USB3.0, PCIe 2.0, SATA, Gigabit Ethernet, MIPI-CSI for embedded applications. It is the ideal solution for POS, vending, infotainment, Medical.
-
product
ALC (AGC) FTTB Optical Receiver
BG9244PL
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai BG9244PL product series have the bandwidth of 47~862MHz,with ALC (AGC) function, two outputs, the output level Vo=104dBμV (Pin:-7~+2dBm). The device has built-level gain and equalization adjustment, visual display about optical power, and can choose 1way or 2 ways high level output by illustration. It applies to FTTB optical access to network, is an ONU optical receiver unit of RFTV radio network with low power, high performance, high cost- effective.
-
product
Network Test LanCaster Pro ST
The NEW Lancaster Pro-ST is a low-cost wire map tester which tests and certifies structured cabling continuity to a TIA568A/B, USOC and ISDN standards. The new Lancaster Pro-ST displays on screen wiring configurations showing the length of all 4 pairs and length of pair to fault up to 150m (500ft).
-
product
Capacitance Tester
ZHANGZHOU HUAYI ELECTRONICS CO.,LTD.
Is a piece of electronic test equipment used to measure capacitance, mainly of discrete capacitors. Depending on the sophistication of the meter, it may display the capacitance only, or it may also measure a number of other parameters such as leakage, equivalent series resistance (ESR), and inductance. For most purposes and in most cases the capacitor must be disconnected from circuit; ESR can usually be measured in circuit.
-
product
Battery Internal Resistance Tester
HDGC-3915
HD Power Test Equipment Co.ltd
Battery Internal Resistance Tester is designed using the advanced AC discharge measurement method to test accurately voltage and resistance of battery. It is strictly designed to evaluate battery performance, state and life-time, which maintain all stationary power systems including Uninterruptible Power System. Battery Internal Resistance Tester can proceed the measurement in a group and in a single section of battery. With accurate testing of resistance and voltage, it gives an indication of battery capacity and technical status. The measurement data can be read on the instrument display directly. And it can also be uploaded to PC simply by using the USB drive. With the analyzing software, you could not only keep a record of the testing result but also have detailed analyzing for the status of batteries in different testing conditions.
-
product
C/I Non-Contact IR
* Safe, non-contact temperature measurement. * Laser spot indicator shows approximate center of target measurement area.* Display temperatures in either Fahrenheit or Celsius.* Adjustable emissivity for optimum temperature reading accuracy on a wide range of materials and surfaces.* Min, Max, Difference and Average temperature functions. * Backlight display for easy readings in any environment.* Auto power off for longer battery life.
-
product
Battery/Antifreeze/Cleaning Fluid Refractometer
RHA-200
Fuzhou Zhongtuo Optoelectronic Co.,Ltd
Digital Hand-held Refractometer is a precise optical instrument that can accurately and quickly measure the refractive index, concentration and other parameters of various aqueous solutions.Dimensions: 55x98x39 mmWeight: 150gPower supply: Rechargeable lithium batteryUser-friendly operation interface, LCD display, making the operation more simple and convenient. More quickly measurements, more accurate and clearer.
-
product
DL379BCOMBO w/ ATTPC3 and Dual NCV
DL379BCOMBO
UEi Test & Measurement Instruments
The DL379BCOMBO HVAC/R Clamp Meter with a CATIV 300V rating, dual level NCV, dual display and a 3-Year limited warranty is a very user friendly clamp meter. The detachable clamp head makes it entirely versatile and the meter for a tech to have in his, or her, tool box. And is combined with the ATTPC3 Pipe Clamp Adapter.
-
product
5 Digit Frequency Meter
CM1-F
CM1-F is an economical and simple frequency meter with a 20mm 5-digit LED display, and the display rangecan be set by pressing the button. Anti-interference design, reliable quality, simple installation and operation.At the same time, it has 2 sets of relay output or 1 set of analog output or 1 set of RS485 (Modbus RTU mode) communication ports for selection.The built-in design of the operation buttons can avoid human misoperation and is suitable for various mechanical use.
-
product
5 Digit Tacho/Linear Speed Meter (1/32 DIN)
CS3-RL
CS3-RL indicator was designed with high accuracy measurement of pulse and frequency.The innovation feature is input from 0.01Hz~100KHz the display resolution will auto-range according input frequency to shift decimal point.A compact body design for small equipment, laboratory instrument, and others.Also are available option relay output, analog output, RS485 Modbus RTU communication for most popular applications.
-
product
ATX Industrial Motherboard With LGA1150 Socket Intel® Xeon® E3-v3 Processor, Intel® C226, ECC DDR3, USB 3.0, SATA 3.0, Dual LANs, DisplayPort/DVI-I/HDMI And CFast™
IMB210
The IMB210 is an advanced ATX industrial motherboard based on the 4th Generation Intel® Xeon® E3/ Core™ i7/i5/ i3/ Pentium®/ Celeron® processors (codename: Haswell) in LGA1150 socket with Intel® C226 PCH. The optimized IMB210 is specially designed for workstations through better computing and visual performance ideally used in every major industry for tasks ranging from financial modeling to designing complex buildings and vehicles. With its built-in Intel® HD Graphics P4000, this industrial grade motherboard delivers great 3D visual performance with triple display capability through DisplayPort, HDMI and DVI-I ports demanded by professional-grade CAD and media/entertainment fields. In addition, the IMB210 supports Intel® Turbo Boost 2.0 technology, Intel® Hyper-Threading technology, Intel® HD Graphics with DX11 support, 3-D Tri-Gate transistors, 32 GB ECC DDR3 1600/1333 memory, and PCI Express 3.0 x16 slot. It also features Intel® Active Management Technology 9.0 (iAMT), Trusted Platform Module 1.2 (TPM), SATA RAID, as well as PCIe x4 expansion making it ideal for applications with added security features.
-
product
EPOCH 650
The large, full VGA transflective display combined with our patented digital high dynamic range receiver provides a stable, striking A-scan representation in any lighting condition. The EPOCH 650 is designed to meet the requirements of ISO 22232-1 and allows a full range of standard and optional flaw detection features.
-
product
DashBox
*Complete computer system configured as a stand-alone dashboard style website.*Designed to host data from one or more Brultech monitors.*Capable of displaying real-time energy, water or gas consumption as well as temperature.*Net metering capable for solar or wind generation systems.
-
product
Digital (1kV below) Insulation Tester
1160 IN
Standard Electric Works Co., Ltd
● Measures insulation (MΩ), Continuity (Ω) and AC voltage.● Three insulation test voltages(DC V) : 250V, 500V, 1000V.● 3½ digital LCD (2000 counts).● 68 × 34mm ( 2.677” × 1.338” ) large LCD display.● LCD backlight display.● Automatic circuit discharge.● Test insulation at rated voltage into a 1mA load.● 200mA short circuit testing current for continuity.● Auto ranging.● Fuse protection.● Data hold function.● BS 16 edition.
-
product
DC Bench Power
XDL Series
AMETEK Programmable Power, Inc.
The Sorensen XDL series II represents the "next generation" of high performance laboratory power supplies. The XDL provides multiple ranges for increased current capability at lower voltages and uses pure linear technology. Unlike other digitally controlled units, the XDL series II provides both numeric and rotary control while the illuminated keys and display legends provide instant confirmation of settings and status.
-
product
Continuous LPR Corrosion Meter
MS2001L
The MS2001L is a microprocessor-based, field-mountable corrosion rate meter. This versatile instrument measures the instantaneous corrosion rate and electrochemical current between the electrodes of any standard 2-electrode linear polarization resistance (LPR) probe. Corrosion rate is displayed on the LCD display.
