Filter Results By:
Products
Applications
Manufacturers
Drivers
translate general instructions into hardware specfic commands.
-
product
Functional Testing
Functional Ethernet testing is done during the research and development phase of a product or service. It can cover many parameters depending on the DUT and the application. Using Xena’s products, your range of functional Ethernet testing includes:*Multicast*40/100G PCS and PMA Layer*Transparent Transport*Energy Efficient Ethernet (EEE)*Microbursts and random IFG*Synchronous Ethernet*Automotive Ethernet*1588v2 Performance Testing*Regression testing*Kernel drivers and NIC testing*Hardware emulation (ASIC*)
-
product
PCIe 16 Bit Arbitrary Waveform Generator - up to 1.25 GS/s on 2 Channels
M4I.6631-X8
The M4i.66xx-x8 series arbitrary waveform generators (AWG) deliver the highest performance in both speed and resolution. The series includes PCIe cards with either one, two or four synchronous channels. The large onboard memory can be segmented to replay different waveform sequences. The AWG features a PCI Express x8 Gen 2 interface that offers outstanding data streaming performance. The interface and Spectrum’s optimized drivers enable data transfer rates in excess of 2.8 GB/s so that signals can continuously replayed at a high output rate. While the cards have been designed using the latest technology they are still software compatible with the drivers from earlier Spectrum waveform generators. So, existing customers can use the same software they developed for a 10 year old 20 MS/s AWG card and for an M4i series 625 MS/s AWG.
-
product
T-Type Thermocouple, 32°F to 500°F Temperature Sensor
745685-T02
T-Type Thermocouple, 32°F to 500°F Temperature Sensor - The T-Type Thermocouple works with NI measurement devices and software to help you acquire temperature data within a measurement system. You can use LabVIEW or FlexLogger software and NI-DAQmx driver software to configure … measurements and predefined scaling coefficients for the T-Type Thermocouple and acquire synchronized temperature data in units of degrees. The T-Type Thermocouple is available in various lengths and configurations including field-cuttable, ready-made sensors, and thermocouple wire extensions with a -20°F to 221°F temperature range.
-
product
Microwave Switches
Communications & Power Industries
- Switches in waveguide, coax, stripline and microstrip- Designs are available from 20 MHz to 35 GHz- Power handling capability as high as 10s of Kilowatts peak- Integral driver, with BITE, can be supplied with any switch
-
product
Laser and Modulator Drivers
Macom Technology Solutions Holdings Inc.
Macom Laser and Modulator Drivers
-
product
PXIe-57857, 12-Bit, 6.4 GS/s, 2-Channel PXI FlexRIO IF Transceiver
785586-01
The PXIe-5785 enables direct RF acquisition up to 6 GHz and generation up to 3 GHz with 12 bits of resolution. You can use it in a dual-channel mode at 3.2 GS/s or in a single-channel interleaved mode at 6.4 GS/s. The PXIe-5785 is ideal for applications that require wideband acquisition and generation with multichannel synchronization, including radar, electronic warfare, and communications. The FlexRIO driver includes support for acquiring and generating waveforms out of the box, and you can use the LabVIEW-programmable Xilinx Kintex UltraScale FPGA to implement custom algorithms for real-time signal processing.
-
product
PCI-6284 , 32 AI (18-Bit, 625 kS/s), 48 DIO PCI Multifunction I/O Device
779110-01
32 AI (18-Bit, 625 kS/s), 48 DIO PCI Multifunction I/O Device - The PCI‑6284 offers analog input, correlated digital I/O, two 32‑bit counters/timers, and analog and digital triggering. The device delivers low-cost, reliable DAQ capabilities in a wide range of applications from simple applications in laboratory automation, research, design verification/test, and manufacturing test. You can add sensor and high-voltage measurement capability to your device with SCC or SCXI signal conditioning modules. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
product
PXIe-5105, 60 MHz, 8-Channel 16 MB, 12-Bit PXI Oscilloscope
783590-01
PXIe, 60 MHz, 8-Channel, 12-Bit PXI Oscilloscope—The PXIe‑5105 high-density PXI oscilloscope has eight simultaneously-sampled channels with flexible settings for coupling, impedance, voltage range, and filtering. PXI oscilloscopes also feature a number of triggering modes, deep onboard memory, and an instrument driver that includes data streaming and analysis functions. This device is ideal for applications with many channels that require up to 60 MS/s or 60 MHz of analog bandwidth. The PXIe‑5105 also features advanced PXI synchronization and data streaming capabilities.
-
product
GPIB-ENET/1000, Ethernet GPIB Instrument Control Device - China 220VAC
781630-10
The GPIB‑ENET/1000 is an IEEE 488 controller device for computers with an Ethernet port. You can use this device to share a single GPIB system among many networked users or to control several test systems from a single networked host. The GPIB‑ENET/1000 features a password-protected web interface for easy configuration. It can also control IEEE 488 devices from anywhere on an Ethernet‑based (LAN) TCP/IP network (Gigabit, 100BASE‑TX, 10BASE‑T). Each device interfaces to and shares up to 14 GPIB devices from several network hosts, and you can control up to 100 GPIB‑ENET/1000 interfaces with a single computer. The device includes a license for the NI‑488.2 driver software, providing maximum reliability for connecting to third-party instruments with GPIB.
-
product
ADLINK PXI Platform Services (APPS)
Software framework services and drivers fully support PXI-2 and PXI-6 software specifications
-
product
PXI-5114, 125 MHz, 250 MS/s, 8-Bit PXI Oscilloscope, 64 MB
779466-02
125 MHz, 250 MS/s, 8-Bit PXI Oscilloscope—The PXI‑5114 low-cost PXI oscilloscope has two channels with flexible settings for coupling, impedance, voltage range, and filtering. PXI Oscilloscopes also feature a number of triggering modes, deep onboard memory, and an instrument driver that includes data streaming and analysis functions. This device is ideal for applications with fast signals that require flexible measurement configurations and up to 125 MHz of analog bandwidth. The PXI‑5114 also features PXI synchronization and data streaming capabilities.
-
product
DIN Rail Mount
Encore Electronics offers a complete line of compact, economically priced instrumentation packaged in standard DIN rail mounted enclosures. Our products include frequency to voltage converters, strain gage amplifiers, notch filters, accelerometer conditioners, and line drivers. Overall package sizes are 3.1″ x 3.3″ x 0.9″ tall (single wide) or 1.6″ tall (double wide).
-
product
PXI/PXIe 16-Channel Digital Output Module
42-412A-024
The 40-412A-024 (PXI) and 42-412A-024 (PXIe) are 16-Channel Digital Output modules with high output voltage and current capability. The outputs can be used for high or low drive and each channel is capable of sourcing 0.5A from the high side or 0.5A sink on the low side. Accidental operation of both high and low side driver on the same channel is prevented by the supplied driver. Outputs are fully protected against over-voltage, over-current and thermal overload, ensuring robust and reliable operation in the toughest test environments. For high side driving, the voltage source is supplied externally, allowing the module to drive high capacity loads separate from the chassis power supply. For low side driving, the external source is not used and the module’s output operates an open collector or open drain driver.
-
product
Ethernet to Modbus RTU Interface
Model 9099
* Use Modbus TCP/IP, VXI-11, or Raw Sockets (Telnet) or to control Modbus RTU slave devices.* No special driver required which eliminates driver problems.* Controllable with Windows PC programs like C, Visual Basic, LabVIEW, VEE, etc that make VISA or SICL calls.* Controllable from MAC/UNIX/LINUX and similar computers with RPC calls.* Interfaces with PLCs or any Modbus TCP/IP Controller.* Fully VXI-11 compliant.* Works with Agilent, NI and Kikisui VISA libraries.* Internal webserver with sample Modbus device control pages for Watlow F4, F4T and EZ-Zone Controllers.* Network connectivity eliminates GPIB Bus Extension problems.* Allows multiple users to access the Modbus network or devices.* 9099 is a 2x to 5x faster than the 8099 and includes a new Modbus device control page.
-
product
4 + 4 LED Driver Test Panel
SCR Elektroniks make 4+4 LED Driver Test Panel to test the driver one by one.
-
product
Magnetrons and Accessories
Teledyne e2v is a leader in cargo scanning technology, delivering products that are integrated into 90% of major systems worldwide.Over 90% of the world’s non-bulk cargo is transported by ship in standardised containers. The containerisation system was developed after World War II and its cost reduction has been a major driver of international trade and globalisation. There are well over half a billion container shipments per annum.
-
product
FOTS-ORL
S-120
•LD Driver, EDFA, ASE Broadband Source, 1X4 Optical Switch•Variable Optical Attenuator, Wavelength Meter•SOA Driver, SLED Driver, Pump LD Driver•Pattern Generator & BERT, SFP Transceiver Driver•4Channel Optical Return Loss Meter (Light Source & Power Meter)
-
product
AFDX ® / ARINC 664 Test And Simulation PCI Module
PC104p-429
*4 or 8 software programmable TX / RX channels*Programmable high / low speed operation*Simultaneous operation of all TX / RX channels*128 MB RAM*Label selective triggering for recording / filtering*Real-time recording and later analysis of multiple channels*Sorting according to SDI field*VXI Plug & Play driver including soft front panel*Supports: C, C ++, C # and .net*Driver support: Windows, Linux, VxWorks and other systems
-
product
PXI Hardware
PXI is now the primary format for ATE Self Integrators. Terotest offer a complete range of PXI equipment that is designed to work together and has full software support for all its PXI modules and drivers.
-
product
GPIB-RS232, Instrument Control Device
779732-10
The GPIB‑RS232 is an IEEE 488 controller device for computers with an RS232 port. You can use this device to integrate an instrument into your system using GPIB. This device transforms a computer with an RS232 serial port into a talker, listener, or controller on the GPIB bus. It can also interface RS232 instruments and peripherals to the GPIB bus. It can implement the physical and electrical specifications of the IEEE 488 and RS232 standards, as well as interpret and execute high-level commands from the serial port, including RS232‑to‑GPIB and GPIB‑to‑RS232 protocol conversions. This device is IEEE 488.2 compatible. The device includes a license for the NI‑488.2 driver software, providing maximum reliability for connecting to third-party instruments with GPIB.
-
product
Driver for Controlling Teledyne Princeton Instruments Cameras
PICAM Driver
Teledyne Princeton Instruments
PICam is the driver for controlling all Teledyne Princeton Instruments cameras and is the platform on which LightField software is built. Teledyne Princeton Instruments also offers the PICam API, which can be used to directly automate any Teledyne Princeton Instruments cameras using the C run-time. This, alongside the PICam SDK, provides efficient and direct control of all cameras. It is available for 64-bit Windows and Linux systems (see Hardware Requirements for details).
-
product
LED Power Driver ATS
8491
1. DC Electronic Load : Chroma 6310A/6330A Series2. Transducer Unit/Module*1 : Chroma A849101/A849102, A849103, A8491043. Time/Noise Analyzer : Chroma 80611 & 80611N card4. Sytem Controller*2 : Industrial PC5. DC Source: Chroma 62000P Series6. Digital Power Meter : Chroma 66200 Series7. OVP/Short Circuit Tester : Chroma 806128. ON/OFF Controller : Chroma 80613*1 : A849101 transfers UUT output signal to voltage signal, and measure by 84911 LED power driver measurement card (200kHz). The optional 80611N Noise card is required for 20MHz ripplecurrent measurement.*2 : The controller includes both 84911 LED Power Driver measurement card and 84903 control card.- 84911: Measure rms current, dimming current/frequency/duty, timing, power & ripple current (200kHz)- 84903 : Provide BL control signal(DC level, PWM, SM bus), and enable ON/OFF signal.C Source : Chroma 6500/61500/61600 Series
-
product
PCI-8366, PCI Host, 100 MB/s, Fiber-Optic Cable MXI-Express Device for PXI Remote Control
781400-01
The PCI‑8366 is an MXI‑Express remote controller for devices or systems over cabled PCI from a computer with a PCI slot. The PCI‑8366 remote controller provides a PCI link over a fiber-optic cable to the PXI‑8368 remote control module when used for PXI system control. Fiber-optic remote control solutions are ideal for long‑distance‑device control and electrical isolation. This link is transparent to software applications and drivers, so computers and servers can control connected devices with no additional programming. With NI remote controllers, PXI modules can be used as if they are PCI devices directly installed in the computer.
-
product
PCI Express Control of PXI Express
PCIe-PXIe-8638
The PCIe-PXIe-8638 PCI Express-to-PXI Express expansion kit provides control of PXI Express modules installed in a PXI Express chassis using high bandwidth PCI Express technology. The extension kit can provide up to 4GB/s using PCIe Gen 2 x8 signaling. With comprehensive hardware and software transparency, the expansion kit enables fast and convenient detection of any PXI cards installed in the system, requiring no additional drivers or software.
-
product
SpaceWire LabVIEW Driver VISA
137
STAR-Dundee's SpaceWire LabVIEW VISA driver has been implemented as a native LabVIEW driver, providing support for the STAR-Dundee PCI family of devices. Software written to control these devices may be deployed on any hardware platform that supports cPCI/PCI and NI-VISA, including both Windows based hosts and LabVIEW Real-Time targets, without requiring modifications to source code. The software is provided as LabVIEW source with password protected block diagrams, allowing users to compile for any target.
-
product
Ion Chromatography
Metrohm IC Driver 2.1 for Empower®
Software drivers for integrating Metrohm IC instruments in "Empower® 3" made by Waters. One license per computer authorizes the operation of IC systems under "Empower® 3".
-
product
Phase Sequence Indicator
PHS 863
Two Functions in one unit including open phase and phase sequence. Large Size alligator clips can easily clip on switch-board terminal. Highly Reliable : Identifies 3 phase sequence and open phase check. Functional design : This model is ideal for installing conveyor lines, pump systems and interconnected drivers. Safety approval : CE marks EN 6101-1 CAT. III. EN 61010-2-031
-
product
C Series Temperature Input Module
The C Series Temperature Input Module features up to 16 channels of temperature input from either thermocouples or RTDS. This module can include anti-aliasing filters, open-thermocouple detection, and cold-junction compensation. Additionally, the module also feature isolation for safety, noise immunity, and high common-mode voltage range.The C Series Temperature Input Module includes the NI-DAQmx driver and configuration utility that simplify configuration and measurements. NI-DAQmx supports NI programming environments as well as Python, ANSI C, C#.NET, and MathWorks MATLAB® software.
-
product
Digital Test Instrumentation
EDigital-Series™
Teradyne’s eDigital IVI driver controls all parallel digital functional test parameters, including per-pin timing, data formats, pattern data, and timing alignment on 64 channels (32 static + 32 dynamic or 32 differential)—each with an 8M pattern depth and results memory.
-
product
AFDX ® / ARINC 664 Test And Simulation PCI Module
PCI-C664
*Supports IEEE 802.3 10/100/1000 Mbit / s full duplex Ethernet connections*Uses SFPs to support both electrical and optical interfaces*Half-size PCI / PCI-X modules*Simulates multiple AFDX® / ARINC 664 end systems*Standard Ethernet processes simultaneous with ARINC 664*Up to 128 output VLs and 512 input VLs*Upper layer protocol handling (ARINC 653, UDP, IP) managed onboard*DMA for high data rate applications*Windows XP / 7, Linux, and LabVIEW Real Time Drivers & APIs (others on request)*Easy to use tool for configuring AFDX® / ARINC 664 end systems (XML based)
