Filter Results By:
Products
Applications
Manufacturers
E-field
space around an electrically charged object. AKA: Electric Field
See Also: Electric Field, Electrical Field
-
product
High Voltage Safe Measurement Systems
For measurement on high-voltage components with certified safety – in test drives, field tests, and on test benches: CSM’s high-voltage measurement systems are specifically designed for the safe and accurate acquisition of temperatures and analog sensor signals in HV environments, especially in electric and hybrid vehicles.
-
product
Field meters
Small, lightweight and low priced non frequency selective Efield meter. It can be used for relatively high field strengths e.g. to observe the field in a TEM cell or a strip line.
-
product
Auger Microprobe
Auger
It is a high specification Auger electron spectrometer with a hemispherical analyzer to provide high throughput analysis of the chemical bonding state at nano to micro areas, and a field emission electron gun also used for EPMA, because it can deliver a large, stable electric current The highly precise eucentric specimen stage makes it possible to perform the previously-impossible analysis of insulators. This in combination with the floating type ion gun offers the versatility to handle any specimen, such as metals and insulation materials, to obtain composition information to and chemical information.
-
product
EV &Recharging Testing
PONOVO has long-term follow-up technology in China and abroad. Based on its own mature intelligent power detection equipment, and according to its own advantages in the field of new energy, PONOVO could be able to provide users with professional new energy test system solutions. In the field of electric vehicle technology, the electric vehicle charging facility detection platform based on the Internet cloud platform was introduced. This platform is one of the few domestic testing platforms that can automatically test the charging piles for network inspection, project acceptance, and factory testing. The platform has the advantages of automatic testing, low usage threshold, and high integration. It is widely used in the detection of relevant charging facilities in more than 20 provinces and cities in China, effectively meets the inspection of electric vehicle charging stations, and provides powerful technical support for the site acceptance test of charging stations.
-
product
Pocket Fieldmeter
FM10
The field strength measurement device with innovative technique and revolutionary design in shirt-pocket format. Simultaneous display of the electric and the magnetic field strength Isotropic measurement of alternating fields. Potential-free and potential-related measurement of electric fields. Frequency range from 10 Hz up to 400 kHz
-
product
Electrostatic Precipitator
HIGHVOLT Prüftechnik Dresden GmbH
Electrostatic precipitators are used for clean process and exhaust gases, for example, in the cement and building materials industry, in steel mills, in conventional power plants, and in waste incineration plants. The dust particles are discharged electrostatically charged by a spray electrode, deflected by a DC electric field and deposited on the electrode.
-
product
Earth Resistance Testers
Earth Resistance Tester is widely applied in ground resistance measurement, loop resistance measurement in fields such as electric power, telecommunications, meteorology, oil field, architecture and industrial electrical equipment, etc. When measuring ground system with loop, there is no need to disconnect the ground wire without auxiliary electrode, which means safer and faster.
-
product
Double Taper Horn Antenna
MDTH series
This product is the antenna that corresponds to the radar pulse immunity test for automotive equipments. Automotive manufacturers have required the electric field strength of 600 v/m. Amplifier system and cable will be cheaper, and will contribute to the ecology.
-
product
Hand-In Type Electromagnetic Anechoic Box (Shield Box)
MY3720
Suitable for weak electric field resistance test, out-of-service test or digital forensics for smart phone, tablet terminal or mobile PC ! !DUT can be operated directly with bare hands while placing it in the box and looking at the inside from the shield window.
-
product
Work Area Voltage Detectors
*Warns of high voltage electric fields using WAVi technology - Work Area Voltage Indication*Visual and audible warning indicates the location of energized fields in a red-yellow-green sequence*Detectors communicate with each other within a mesh network*Remotely control detectors through the Lookout mobile app*Battery life of up to 500 hours in Monitor mode and up to 8 hours in Alert mode*Durable water-resistant housing
-
product
Guided UWB Radar TLI Signal Processor
EFP-IL
The new panel-mount EFP-IL Guided UWB Radar Signal Processor uses MOHR's Electric Field Perturbation (EFP) technology to provide the industry's most accurate real-time liquid level and multiphase flow measurements.
-
product
Photonic Electric Field Sensor System
Model No. 200-04
SRICO Model No. 200-04 Photonic Electric Field Sensor System has the ability to measure electric field with minimal disturbance to the field. The lightweight fiber-optic cables allow for easy placement of the E-field probe, allowing it to be unencumbered by the use of heavy coaxial cables that may disturb the field being measured. The dielectric E-field probe is electrically passive.
-
product
IC Side Channel Analysis
These probes allow you to couple fast, transient magnetic field, E-field, and current pulses into ICs.
-
product
Antenna, Loop
EM-6879 | 10 KHz – 30 MHz
The EM-6879 Loop Antenna is used for magnetic field measurements over the frequency range of 10 kHz to 30 MHz. The EM-6879 is designed for use with any 50 ohm Receiver System. The antenna has a balanced Faraday shield that reduces its response to electric fields to a vanishingly small amount so that it can produce a practically pure magnetic field response.
-
product
Antenna, Log Periodic
EM-6952-1 | 1 GHz – 2 GHz
The Electro-Metrics EM-6952-1 Log Periodic Antenna operates over the 1 to 2 GHz frequency range. The EM-6952-1 is capable of operating either as a transmitting or as a receiving antenna over the frequency range of 1 to 2 GHz. Its linearly polarized designed permits separate measurement of horizontal and vertical electric field components over its established range. Enclosed in a weather resistant radome, this antenna is suitable for indoor or outdoor usage.
-
product
Software
EFC-400
EFC-400 is a quasi industrial standard for computing and simulating electric and magnetic fields.
-
product
Test Fixture, Shielding Effectiveness
EM-2108 | 1.5 GHz – 10 GHz
The EM-2108 is a standard test fixture for evaluation of the electromagnetic shielding effectiveness (SE) of planar materials. The fixture is a section of coaxial transmission line broken to allow the insertion of planar test materials. Although ASTM D4935-10 is currently limited to an upper frequency of 1.5 GHz, the EM-2108 meets and complies fully with both the impedance and SE requirements called out in ASTM test method D4935-10 up to 10 GHz. These results are shown in Figures 1 & 2. The measured data relates to the shielding effectiveness due to a plane wave (far field EM wave) from which near field values for magnetic and electric fields may be inferred.
-
product
Metering
Based on our field experience, we have developed one of the EASIEST TO INSTALL meter interfaces on the market today. If you have an electric, gas, steam, or water meter that is able to output data via Modbus RTU or Modbus TCP, then we probably have a pre-made template that converts your meter''s data to BACnet/IP. We also have a product for pulse meters.
-
product
Frequency Shaped Isotropic Electric Probes
PI-SH-FCC, PI-SH-ICNIRP
An isotropic electric field probe with shaped frequency response meeting the ICNIRP or FCC RF safety standards for occupational and general public exposure limits (see the specified frequency ranges below). Meter readings are shown in % of the STD – standard reference level, eliminating the need to know the source frequency. Probe output is proportional to RF power density in the whole specified power range, producing the correct RF power measurements in single and multi-signal environments, typically present at multiple antenna sites.
-
product
Magnetic & Current Sensors
From the International Space Station to a simple electronic compass, we can provide a solution to meet your magnetic semiconductor needs. The F.W. Bell® product line was founded in 1944. Since then we have been a pioneer in developing instrumentation to measure electric current and magnetic fields.
-
product
Field Meter
FM 6
The field meter FM 6 is a multi-purpose electrosmog meter for alternating electric and magnetic fields. The wide-band frequency range from 16 Hz up to 100 KHz
-
product
RF Safety Monitoring
fieldSENSE 2.0
LBA's FieldSense 2.0 personal RF safety monitors are an effective and economical means to monitor the strength of electromagnetic (RF) fields from wireless cell phone towers, microwave ovens, television stations, and other common workplace RF sources between 50 and 6000 MHz, E-field and H-field (sensed as a plane wave). The Personal RF Monitor is essential RF safety equipment in complying with FCC, OSHA, Canadian and other workplace rf safety requirements.
-
product
Modeling Capacitors, Inductors, Insulators, Coils, Motors, and Sensors
AC/DC Module
The AC/DC Module is used for simulating electric, magnetic, and electromagnetic fields in static and low-frequency applications. Typical applications include capacitors, inductors, insulators, coils, motors, actuators, and sensors, with dedicated tools for extracting parameters such as resistance, capacitance, inductance, impedance, force, and torque.
-
product
Amp, Power Factor & VAR Recorder
Varcorder
The Varcorder measures and records Amps and Power Factor. A voltage constant is then applied in software to calculate VARs. The Varcorder uses the same current sensor technology as the original Ampstik. This patented amp sensor does not use magnetic materials and has no moving parts. The opening of the sensor is electronically closed, and external currents are electronically rejected. The accuracy, external current reject, and range of currents measured by the patented amp sensor substantially exceed the performance of the best clamp-on sensors. The true power factor is calculated by measuring the electric field in comparison with the current reported from the amp sensor. The key feature of the unit is the ability to leave it deployed on the line to record readings every 15 minutes for 90+ days. It easily attaches to the line with a standard shotgun style hotstick. Once on the line, it immediately begins to collect and record the current and power factor on the line.
-
product
Near Field Probes 30 MHz up to 6 GHz
XF1 set
The XF1 set of near field probes consists of 4 passive near field probes and one passive E field probe for making measurements in the development phase of the magnetic and electric fields in ranges from 30 MHz to 6 GHz. Due to their integrated impendance matching, the probes are less sensitive in the lower frequency range than the RF type probes. The probe heads of the XF1 set allow for the step by step identification of interference sources of the magnetic field on an electronic assembly. At first, for example the XF-R 400-1 detects the fields which the assembly emits in total. Next, using higher resolution probes the interference sources can be more precisely detected. The E field probe is used for the detection of electric interfering fields near the assemblies. With trained use of the near field probes, field orientation and field distribution can be detected. The near field probes are small and handy. They have a sheath current attenuation and are electrically shielded. They can be connected to a spectrum analyzer or an oscilloscope with a 50 Ω input. They have an internal terminating resistance.
-
product
Conductivity Meters
Conductivity meter measures the amount of electric current or conductivity in solution.A conductivity meter measures the health status of the natural water body.It is very useful in the field of water.
-
product
Portable Multifunction Calibrator
M143
Clarke-Hess Communications Research
The M143 Multifunction calibrator is a cost saving solution for calibration of electric meters with up to 1000 V and 20 A. It offersa basic accuracy of 0.01% in DC voltage for calibration of 3 and 4 digit multimeters. The resistance function is covered byeight fix resistors in range from 10 to 100 M. The calibrator offers TC temperature sensor simulation. It can be deliveredoptionally as well with RTD temperature sensor simulator. Thanks to its small dimensions and low weight the unit can be usedeasily for field calibration work.
-
product
Portable Three Phas Multifunction Electric Meter Calibrator
GF312V2
Beijing GFUVE Electronics Co.,Ltd.
GF312V2 portable three phase multifunction energy meter calibrator is with comfort design, small size, and light weight. It is suit for electric power departments, measuring and quality examining departments and electric lab to field use.
-
product
Hand-In Type Electromagnetic Anechoic Box (Shield Box)
MY3710HS
Higher shielding performance than MY371080dB. Suitable for weak electric field resistance test, out-of-service test or digital forensics for mobile phone, smart phone or tablet terminal! DUT can be operated directly with bare hands while placing it in the box and looking at the inside from the shield window.
-
product
3D Microscope
BVM-5006
BVM-5006 Electric 3D Microscope features the quality optical system, high resolution, large field of view, high zoom ratio, novel design and one-up technology, easy and automatic operations. Includes: Motorized zooming, motorized observation angle for changing and optional motorized focusing. The speed can be adjusted while changing observation angle. With the angle attachment, the microscope can realize 3D image effects for observing the components and deep holes. The LED lights can generate high brightness. Theoretically the service life of LED lights can reach 20,000 hours. The LED lights with area control function can illuminate from different angles for convenient multi-angle inspections. The M-N3D Microscope can be widely used in micro-electronics, automated monitoring and testing industries. By selecting the appropriate objectives and video couplers, different magnification, field of view and depth of field can be acquired. Digital and Analog video systems can meet the different users' demands.
