Filter Results By:
Products
Applications
Manufacturers
Electronics Test
Devices whose quality of operation is based on the effects of electrons.
-
product
Functional Test
UTS
The UTS functional test system is perfect for electronics manufacturing operations that have a mix of products where operators load and unload devices under test (DUT) and routinely change out fixtures for each type of DUT.
-
product
6TL24 Combinational Base Test Platform
H71002400
The 6TL24 is the Base platform ideal for Combinational test (ICT+FCT) in low to mid volume, high-mix electronics productions. A dual-stage pushing mechanism will allow performing both, the FCT and the ICT test, without the need of changing the test platform and with a low cost fixturing technology. To do so, the exchangeable cassette fixture must be designed with two-level probes. IN the 6TL24, the second level is reached thanks to a pneumatic actuator.
-
product
High Speed Test Bench
AT444
AC motor with mechanical multiplying gearbox test benches allow precise programming of all drive parameters required for accurate rotating devices test.The use of special high-speed bearings, mechanical components and parts wear resistant leads to a large life. The supply includes the electronic drive and control as well as the entire oil cooling unit.
-
product
High Temperature Diametral Extensometers (1000 C)
Model 3580
Jinan Testing Equipment IE Corporation
This model is for diametral strain measurement with furnace and induction heating systems. Quartz rods and water-cooling allow the unit to be used for high temperature testing of metals, ceramics and composites. With induction heating, this model often can be used without water-cooling. When used in furnaces, the extensometer is often mounted directly to the furnace side cut-out. Optional load frame mounting brackets are available for supporting the extensometer in cases where furnace mounting is not possible. These optional mounts are used with induction heating or furnace systems. The Model 3580 extensometers are strain gaged devices, making them compatible with any electronics designed for strain gaged transducers. Most often they are connected to a test machine controller. The signal conditioning electronics for the extensometer is typically included with the test machine controller or may often be added. In this case the extensometer is shipped with the proper connector and wiring to plug directly into the electronics. For systems lacking the required electronics, Epsilon can provide a variety of solutions, allowing the extensometer output to be connected to data acquisition boards, chart recorders or other equipment.
-
product
Automated Test and Programming Station
The Scorpion BRiZ
The primary goal of an electronic test strategy is to achieve the highest possible test coverage. Often, a combination of test tools and techniques needs to be integrated in order to meet this challenge. A decisive factor in selecting the optimal test strategy is cost. So, choosing a test platform that results in the highest test coverage for your investment is essential.But, what if in addition to test, you require in-system or on-board programming? What would be the best way to handle this while staying within budget and meeting production timelines?
-
product
HTOL RF Testing Systems
Becker Nachrichtentechnik GmbH
Fully Automatic Test Systems for Lifetime Simulations of Electronic Components. Each output offers a separate, analogue level control. This ensures highest precision in level during a long term usage. A graphical user interface enables an intuitive and easy control.
-
product
Radar Target Simulator
E8707A
Rapid developments in the autonomous vehicle and demand for greater safety features is fueling the need for more sensitive and accurate automotive radar technology being deployed in advanced driver assistance systems (ADAS). With its rich expertise in radar test technology, Keysight now offers the E8707A radar target simulator to help automotive electronics manufacturers confidently simulate radar targets in various realistic scenarios.
-
product
Load Pull
All Focus tuners use extremely efficient calibration and tuning algorithms and control electronics based on LAN control (iTuner). This is a merger our proven tuner technology with state of the art control electronics to create the latest tuner generation. The on-board micro-processor and tuning firmware form a self-contained and fully calibrated test instrument. The micro-processor inside the tuner accepts ASCII format communication, via an industry standard TCP/IP interface, controls up to nine stepper motors (tuner axes) and executes interpolation and tuning functions for single probe (CCMT) tuners (one probe per frequency range). For tuners with more than one independent probe (MPT) covering the same frequency range to allow for harmonic tuning, external computing power is required, because of the exponentially growing number of combinations of tuner states (slug positions).
-
product
Regenerative AC Load
61800
Chroma Power Electronics Test Solutions not only apply in the industries of Information Technology, Communication, Aerospace and National Defense, but also in energy efficient products such as Hybrid Automobiles, LED luminance devices, solar and fuel cells that are developed aggressively under the pressure of natural resource constraints. Chroma has a wide variety of instrumentation including AC Power Sources, DC Power Supplies, DC Electronic Loads, AC Electronic Loads, Digital Power Meters, and Automatic Test Systems that are ideal for power input/output terminal tests and dynamic simulation.
-
product
Digital/Pattern/PE Card
PE16S
The PE16S represents a new level of performance and capabilities for PXI-based digital instrumentation. Based on the proven architecture of the PE16, the PE16S offers high performance pin electronics and an enhanced timing generator in a compact, 3U PXI form factor. Each card can function as a stand-alone digital subsystem or if required, multiple cards can be interconnected, supporting up to 256 bi-directional pins (16 boards). The PE16S offers 16 programmable level input or output channels with 2 PMU . The PE16S also supports deep pattern memory by offering 32 M of on-board vector memory with per channel dynamic direction control running test rates up to 66 MHz.
-
product
PCB Test Fixtures
ATE, ICT, semiautomatic & manual electronic test fixtures, PCB test fixtures, cable test fixture, wiring harness test fixtures, dedicated test fixtures, functional test fixtures, electronic test fixture programming. PADS Schematic capture, circuit board layout, PCB design prototype, solder paste stencils, X-Y coordinate data, B.O.M. maintenance, and manufacturing documentation, Gerber data.
-
product
Electrical Engineering Services
Reston Software provides state-of-the-art, U.S.-based electronic design services. We provide these services part of our systems-related offer, as well as on a stand-alone basis.We specialize in maintaining and upgrading 70's and 80's electronic equipment. We provide on-call support services for test, measurement, and laboratory equipment.
-
product
VG-Receiver
uwe electronic offers a wide variety of VG-Receiver for 4, 12 or 24 VG-Interface-Blocks. From bench-top test applications to complete rack and stack solutions, we provide a reliable and economical test based mass interconnect.
-
product
AC DC High Voltage Divider
NMC make products are the ideal equipment for HV measuring products are the ideal equipment for HV measuring instruments, apply in power system, electronic equipment factory to test frequency AC high voltage and DC high voltage. This product is composed by HV measuring part and LV display instrument. HV part and LV display instrument are separate when working, it is safe and reliable.
-
product
Drop-In Functional Test Fixtures
Circuit Check’s drop-in base fixture and replaceable personalized plates are the ideal solution where production volumes are lower and the need to change from one fixture and test program to another occurs quickly. Interchangeable test fixture drop-ins enable the same test system to be quickly reconfigured with different tooling and probe patterns for different products. This maximizes equipment re-use, while minimizing the cost for each new test. With Circuit Check’s base fixture and drop-ins, the wiring and test electronics are not disturbed, thus ensuring configuration consistency each time the system is re-tooled.
-
product
Digital/Pattern/PE Card
PA32S
The PA32S represents a new level of performance and capabilities for PXI-based digital instrumentation. Based on the proven architecture of the PE32, the PA32S offers high performance pin electronics and an enhanced timing generator in a compact, 3U PXI form factor. Each card can function as a stand-alone digital subsystem or if required, multiple cards can be interconnected, supporting up to 512 bi-directional pins (16 boards). The PA32S also supports deep pattern memory by offering= 32 M of on-board vector memory with dynamic per pin direction control and with test rates up to 33 MHz. With new 32M capture/log memory, PA32S can capture 32 channels fail log.
-
product
Universal Offline AXI Systems
AXI XT-6 Series
The XT-series provides the advanced inspection capability of Nordson TEST & INSPECTION's inline system in a smaller footprint manual load/island of automation system. The platforms are designed for flexibility and ease of use for a wide variety of products requiring 2D and 2.5D automated X-ray inspection. The XT-6/XT-6A platform is a highly flexible automated X-ray inspection system with minimum footprint and a parallel-kinematic Hexaglide manipulation unit for extreme-angle off-axis image acquisition with high resolution. It is suitable for high-quality X-ray analysis of electronic assemblies and material analysis of parts that require flexible part manipulation with multiple inspection angles. For batch modes and volume inspection the XT-6 can be equipped with a single-sided conveyor setup and magazine load/unload station (XT-6A).
-
product
Test System Elowerk
eloZ1
The eloZ1 Manufacturing Defects Analyzer is an in-circuit tester of the latest generation. It reliably finds connection errors and assembly errors in electronic assemblies. The test electronics can be integrated both in table systems and in inline systems.
-
product
Standard High Speed A/D Converters
Analog Devices high speed A/D converters (ADCs) offer the best performance and highest sampling speed in the market. The product offerings include low IF A/D converters (20 MSPS to 125 MSPS), high IF a/d converters (125 MSPS to 1.3 GSPS), and wideband ADCs (>1 GSPS). The high speed a/d converter portfolio offers cost and performance optimized solutions for various applications such as communications infrastructure, electronic test and measurement, and aerospace and defense.
-
product
High and Low Temperature & Low Pressure Chamber
LAP-100
It is according to GB10590 / GB15091 low temperature / low pressure test chamber requirements; GB11159 low pressure test chamber requirements; GB / T2423. 25-1992 low temperature / low pressure integrated chamber requirement; GB / T2423. 26-1992 High temperature / low pressure integrated chamber requirement; GJB150. 2-86 low temperature / low pressure test etc standards. It’s used to test the In aviation, aerospace, information, electronics and other fields, to determine the instrumentation, Electrical products, materials, components, equipment etc.
-
product
Environmental Test Chamber
Test Chambers are used widely in temperature variation tests, cold resistance tests, and for low-temperature storage in the areas of aerospace and aviation, electronic instruments, electrical products, materials, parts, and components.
-
product
Programmable Electronic Load
Shenzhen UYIGAO Electronic Technology Co., Ltd
UYIGAO DC electronic loads provide you with the flexibility to test a wide range of power sources. Perform both static and dynamic tests to ensure that your devices can handle the steady state and occasional transient loads. The 16-bit voltage, current, and power-measurement systems provide accuracy analysis.
-
product
Military & Aerospace Solutions
Military and aerospace electronics spans a vast array of complex applications, including communications, vehicle control, radar, electronic warfare and countless others. Although the applications are widely varied, there are similarities in the requirements as well. Typically these electronic systems, whether COTS (Commercial Off- the-Shelf) or custom developed for the application, share similar requirements for ruggedness, reliability, and precision. Our customers don’t have room for error, mission critical hardware test systems must perform as designed. Circuit Check provides military and aerospace testing solutions for ITA’s, Self-Test Fixtures and Automated Test Systems that meet the stringent needs of this marketplace.
-
product
Programmable AC Power Supply
IT7300 Series
In order to meet the bigger range of AC power supply and more complex change characteristics, engineers need more powerful and stable AC power supply to simulate the actual working environment. IT7300 series is the best solution in this area. IT7300 series can be widely applied in the electronics and electrical industry, lighting, aviation, military, specification verification of RD, the use of laboratory testing and factory production online test etc.
-
product
Leak Tester
LSD-01A
Jinan Leading Instruments Co., Ltd.
LSD-01A Leak Tester is applicablein leak testing of pouches, bottles, pipes, cans and boxes of foodstuff,pharmaceutical, medical, daily chemistry, automotive, electronic components, stationary and other industries. It’ s also applicable in the leak testing ofthe specimens after falling tests and pressure resistance tests.
-
product
Test Laboratory
We provide research and test laboratory services for electronic devices, systems and solutions in our laboratory located in Jyvskyl, Finland. Laboratory services include:Assistance and consultation in product certificationElectromagnetic compatibility measurements and testing (EMC/ESD)Radio frequency testing (RF)RF and hardware interoperability testingAntenna performance measurementsEnvironmental, mechanical and reliability testingFailure analysis and quality assurance
-
product
Test And Repair
If you are responsible for maintaining a system where faulty electronic modules are not readily replaceable. Innovasys can assist by providing cost effective repair services or by developing support tools to allow in-house repair.Our IPC J-STD-001 certified technicians provide test and repair of electronic modules and are backed by a team of electronics engineers. This gives us the capability to diagnose and repair complex circuitry.Innovasys provides test and repair services to the Defence Materiel Organisation. Our technicians are experienced in effecting repairs to meet strict quality requirements on complex multi-layered circuit card assemblies.
-
product
Signal Generators
Dongguan Longwei Electronic Technology Co., Ltd.
An electronic device that generates repeating or non-repeating waveforms used to test and evaluate electronic test equipment.
-
product
Color Card Winder
TY390
TESTEX Testing Equipment Systems Ltd.
Color Card Winder is specially designed to wind cards for Textile Industry. The machine is used for making color cards, which will be fed into the photo spectrometer of the computer color matching systems. The machine is also fitted with electronic counters for pre turn settings.It is especially suitable for the following purposes:Sample cards, whiteness test, ultraviolet ray resist test, sample standardization, color comparison, color chart etc.
-
product
Modular Power
AMETEK Programmable Power, Inc.
ReFlex Power™ is a high density, programmable power module system providing DC, AC and electronic load assets all under control of a single controller. ReFlex Power™ (RFP™) provides a reconfigurable, flexible platform ideal for ATE and production test environments where RFP™ can provide programmable stimulus and bias power as well as programmable loads for the device(s) under test.
