Filter Results By:
Products
Applications
Manufacturers
FET
Rely on an electric field to control the shape and channel of a charge carrier in a semiconductor material.
-
product
3200W to 4080W -Single Output - 3200W To 4080W - Single Output
TPS Series
*400/440/480 VAC (Nom.) 3Ph Delta or Wye*Fully Regulated, Wide Range Adj. Output*Voltage and Current Programming*-40°C (start up) to +70°C operation*>92% Efficiency*PMBus™ Communication*Built-in ORing FET for parallel operation
-
product
General Purpose Low-side MOSFET Drivers
Renesas' family of low-side FET drivers are very high-speed matched dual-drivers capable of delivering peak currents of 2.0 amps into highly capacitive loads and excellent at driving large capacitive loads with minimal delay and switching times. The high-speed performance is achieved by means of a proprietary "Turbo-Driver" circuit that speeds up input stages by tapping the wider voltage swing at the output. Improved speed and drive capability are enhanced by matched rise and fall delay times. These matched delays maintain the integrity of input-to-output pulse-widths to reduce timing errors and clock skew problems. This improved performance is accompanied by a 10 fold reduction in supply currents over bipolar drivers, yet without the delay time problems commonly associated with CMOS devices. Dynamic switching losses are minimized with non-overlapped drive techniques.
-
product
PXI Solid State MUX, 4 pole, 40 channel
40-680-404
Based on FET switches, the multiplexers have no wear out mechanism and include fault protection that ensures the multiplexer automatically disconnects when PXI power is not applied. Available configurations for the 40-680 range vary from a single 160 to 1 MUX to a 20-bank, 8 to 1 MUX in a single PXI module.
-
product
JFET Input Amplifiers
Analog Devices JFET input op amps or FastFET high speed (>50 MHz) input op amps provide high input impedance and ultralow input bias currents for high speed applications. The majority of our FET input op amps feature wide supply ranges from +5 V to 12 V or higher and feature rail-to-rail outputs enabling wide dynamic range.
-
product
POL Converter
Renesas offers a rich product lineup focused on the step-down type switching power supplies with built-in FET from small current applications to large current applications, depending on the supplied current.
-
product
DC Power Supplies
SGe Series
AMETEK Programmable Power, Inc.
The SGe is an economical, FET based, high switching speed, programmable, dc power supply alternative to SCR and IGBT based dc supplies.
-
product
PXI Solid State MUX, 20 bank, 8 channel
40-680-001
Based on FET switches, the multiplexers have no wear out mechanism and include fault protection that ensures the multiplexer automatically disconnects when PXI power is not applied. Available configurations for the 40-680 range vary from a single 160 to 1 MUX to a 20-bank, 8 to 1 MUX in a single PXI module.
-
product
Solid-State Relays Packaged in a 16-Pin DIP
Series C75-2
Series C75-2 solid-state relays are packaged in a 16-pin DIP, with surface-mount or through-hole mounting available. They utilize a power FET switch that is protected against overload and short-circuit currents. 2S versions provide an open-collector trip status feedback to the relay’s control side. 2SH versions add an internal transient voltage suppressor for inductive loads.MSL 6C75 relays are controlled with 4.5-5.5VdcC = Through-hole mount SC = Surface mountAvailable options include:C75-2 1A, 60Vdc Load; short-circuit protectionSC75-2 1A, 60Vdc Load; short-circuit protection C75-2S 1A, 60Vdc Load; short-circuit protection and trip satusSC75-2S 1A, 60Vdc Load; short-circuit protection and trip status C75-2SH 1A, 60Vdc Load; short-circuit & transient voltage protection, and trip statusSC75-2SH 1A, 60Vdc Load; short-circuit & transient voltage protection, and trip status
-
product
Oscillators
Ducommun’s oscillator family includes FET based dielectric resonator oscillators (OFD), phase locked oscillators (OPL), Gunn diode based low cost Gunn oscillators (OGL), bias tuned Gunn oscillators (OGB), mechanically tuned oscillators (OGM), varactor tuned Gunn oscillators (OGV), injection locked Gunn oscillators (OGI) and Gunn oscillator bias regulators and modulators (OGR and OMR). In the mechanically tuned Gunn oscillator family, the ultra broadband series (OGF) delivers up to full waveguide tuning bandwidth.
-
product
FET Solid State Switch, 300 kHz to 8 GHz, SPDT
U9397A
The Keysight U9397A solid state switch maximizes your frequency range from 300 kHz up to 8 GHz, offering excellent performance with high isolation, low SWR and fast switching speed. Applications include instrumentation, communications, radar, and many other test systems that require high speed RF and microwave SPDT switching.
-
product
PXI-2535, 544-Crosspoint, 1-Wire PXI Matrix Switch Module
778572-35
544-Crosspoint, 1-Wire PXI Matrix Switch Module—The PXI‑2535 is a high-density 4x136 PXI matrix switch module that is ideal for routing low-power DC signals in validation test systems of mass produced devices such as semiconductor chips and printed circuit boards (PCBs). Featuring field-effect transistor (FET) relays, the PXI‑2535 offers unlimited mechanical lifetime and switching speeds up to 50,000 crosspoints/s. It also features onboard relay counting for relay monitoring and deterministic operation with hardware triggers to improve test throughput.
-
product
Low Profile Solid State Relays, MIL-PRF-28750 Screened
Part No. LD00KM
The Series LD00KM solid-state relays are screened utilizing MIL-PRF-28750 test methods and are packaged in low profile hermetically sealed cases. These relays are constructed with state-of-the-art solid state techniques and feature fully floating power FET output technology. This allows the load to be connected to either output terminal and provides a low ON resistance. The input (control) and output are optically isolated to protect input logic circuits from output transients.MSL 1Available options include:LD00KM 10A, 270Vdc Load; 4.2-32Vdc Control
-
product
X-Ray And Gamma Detector Systems
The XR-100CR is a new high performance x-ray detector, preamplifier, and cooler system using a thermoelectrically cooled Si-PIN photodiode as an xray detector. Also mounted on the 2-stage cooler are the input FET and a novel feedback circuit. These components are kept at approximately -55 °C, and are monitored by an internal temperature sensor. The hermetic TO-8 package of the detector has a light tight, vacuum tight thin Beryllium window to enable soft xray detection. The XR-100T-CdTe represents a breakthrough in xray detector technology by providing “off-the-shelf” performance previously available only from expensive cryogenically cooled systems. The XR-100-CdTe is also suited for measuring gamma rays.
-
product
PXI RF Matrix Switch Module
PXI RF Matrix Switch Modules are organized into rows and columns and provide maximum flexibility for switching systems by allowing you to connect any channel to any other channel. PXI RF Matrix Switch Modules use a variety of relay types, including electromechanical armature relays, reed relays, field-effect transistor (FET) relays, and solid-state relays, each with their own benefits, allowing you to choose a matrix that fits your requirements. To program the switches, you can use the IVI-compliant NI-SWITCH driver software, complete with help documentation, example programs, and a soft front panel application for interactive control of switches. For intelligent management of complex switch systems, NI Switch Executive provides additional software tools to help you design, build, and deploy your switching system.
-
product
PXI Solid State MUX, 2 bank, 80 channel
40-680-005
Based on FET switches, the multiplexers have no wear out mechanism and include fault protection that ensures the multiplexer automatically disconnects when PXI power is not applied. Available configurations for the 40-680 range vary from a single 160 to 1 MUX to a 20-bank, 8 to 1 MUX in a single PXI module.
-
product
Active Differential Probe
DF-600
The DF-600 Differential Active Probe is a high input impedance and low input capacitance probe. It also supports extremely high frequency bandwidth, and high voltage input. It is designed using three OP amps, namely two FET buffer OP amps and a low offset OP amp. Therefore, even with long-term operations, the measured voltage will not drift. The voltage offset always approach 0 volts. (USB power supply should be 5V ±2%). The following diagram shows the circuit of DF-600.
-
product
CTL503
The CTL503 Curve Tracer is a low-cost transistor (BJT and FET) computer controller curve tracer. Unlike other simple curve tracing units the CTL503 is designed to measure devices to 100V and upto 3A. Four collector resistors (relay selected) allow the user to test the smallest of BJT’s and FET’s as well as extracting meaningful curves from larger TO3/TO247 packaged devices. Limits on both peak test voltage and peak test current can be easily set to prevent exceeding device parameters.Pulse testing (80us/300us) is used to minimise device heating and to ensure the CTL503 can be powered via USB. This may be disabled for smaller parts.Connected and powered via USB and running our own free software the CTL503 is easily configured using a built in wizard (for quick results), or the user can adjust every instrument parameter to suit. Works with EPIC 21.010 and above.Users can save data from runs, as well simply grab images directly from EPIC.Connections are made to the DUT (device-under-test) with the built-in colour coded test leads with crocodile clips.
-
-
product
PXI Solid State MUX, 5 bank, 32 channel
40-680-003
Based on FET switches, the multiplexers have no wear out mechanism and include fault protection that ensures the multiplexer automatically disconnects when PXI power is not applied. Available configurations for the 40-680 range vary from a single 160 to 1 MUX to a 20-bank, 8 to 1 MUX in a single PXI module.
-
product
Low Profile Solid State Relays, Utilizing MIL-PRF-28750 Test Methods
Series KD and LD
Your product description goes here.Series KD and LD solid-state relays utilize MIL-PRF-28750 test methods and are packaged in low-profile hermetically sealed cases. They feature fully floating power FET output technology. Options include short-circuit and current overload protection plus a status output line. Switch status returns the true status of the output switch and is optically isolated from the load.MSL 1KD & LD relays are controlled with 15mAdc/3.8Vdc (TTL), and 1mAdc/0.3Vdc (CMOS).Available options include:KD00CK 5Adc, 60Vdc Load KD02CK 5Adc, 60Vdc Load; with switch statusKD20CK 5Adc, 60Vdc Load; with short circuit protectionKD22CK 5Adc, 60Vdc Load; short circuit protection & switch statusLD00CM 10Adc (5Adc without heat sink), 60Vdc LoadLD02CM 10Adc (5Adc without heat sink), 60Vdc Load; with switch statusLD20CM 10Adc (5Adc without heat sink), 60Vdc Load; with short circuit protectionLD22CM 10Adc (5Adc without heat sink), 60Vdc Load; short circuit protection & switch status
-
product
DrMOS (Driver + FET)
Renesas' high-performance DrMOS power modules combine a high-performance FET driver and MOSFETs in an advanced package to create high-density DC/DC converters.
-
product
Miniature Solid-State Relays
Series C47F
The Series C47F miniature solid-state relays utilize a photovoltaic generator driving high-performance power FET chips to provide low-output on resistance and high-output switching capability. The virtual elimination of offset voltage makes these relays ideal for low level switching applications as well. Bidirectional switching versions (Series C46F) are available. MSL 6Available options include:C47F-10 1.75A, 50Vdc Load; 3.8-32Vdc ControlC47F-20 1A, 90Vdc Load; 3.8-32Vdc Control C47F-30 0.6A, 180Vdc Load; 3.8-32Vdc ControlC47F-40 0.4A, 360Vdc Load; 3.8-32Vdc Control
-
product
Low Profile Solid State Relays, MIL-PRF-28750 Screened
Part No. LD24KK
The Series LD24KK solid-state relays are screened utilizing MIL-PRF-28750 test methods and are packaged in low profile hermetically sealed cases. These relays are constructed with state-of-the-art solid state techniques and feature fully floating power FET output technology. This allows the load to be connected to either output terminal and provides a low ON resistance. The input and output are optically isolated to protect input logic circuits from output transients. A trip status indicator turns on when an overcurrent condition has occurred and the short-circuit protection has been activated.MSL 1Available options include:LD24KK 5A, 270Vdc Load; 4.2-16Vdc Control, Short Circuit Protection and Trip Status
-
product
Military-Style DC Solid-State Relay for High-Current Pulse Load Applications
Part No. M33-2N
The M33-2N is a military-style DC solid-state relay designed for high-current pulse load applications. It features the latest power FET output technology to minimize ON resistance. This feature provides minimum output voltage drop and allows the M33-2N to switch high pulse currents up to 100 amps at higher temperatures than those allowable with bipolar devices. The M33-2N utilizes transformer isolation to protect against transients, and are through-hole mountedMSL 1 Available options include:M33-2 7Adc, 60Vdc Load; 4.5-5.5Vdc (bias voltage), 80µA (CMOS) Control;
-
product
Solid-State Relay with Power FET Switch to Protect Against Overload and Short-Circuit Currents
Part No. SR75-2
The SR75-2 solid-state relay utilizes a power FET switch that is protected against overload and short-circuit currents. The short-circuit protection feature not only provides protection should a short or overload occur while the relay is on, but will provide protection should the relay be switched into a short. It comes in through-hole or surface-mount 16-pin DIP packages.MSL 6Available options include:SR75-2 0.5Adc, 400Vdc Load; 3.8-32Vdc Control; through-hole mountSR75-2S 0.5Adc, 400Vdc Load; 3.8-32Vdc Control; surface mount
-
product
Switch Drivers
Macom Technology Solutions Holdings Inc.
MACOM’s switch drivers bridge the gap between digital control signals and the analog voltages and currents required to drive our extensive family of RF, microwave and millimeter wave PIN diode and FET switches.
-
product
CobaltFx 20 GHz 4' FET RF Cable Kit
This is a set of 4 cables, standard length 4 ft, for one extender: ULC50SMSM.4 cable (4)
-
product
Amplifier Module
LNAM-FBX
Ultra-low-noise voltage amplifier module (LNAM) with ac coupled FET input allowing measurements between 1 Hz and 20 MHz. High gain precision and low distortion are achieved by using internal negative feedback and >1000 V/µs output stages.
-
product
Volume Production Oscillators
Volume production oscillators utilize either high performance GaAs Gunn diodes with high Q cavity designs or state-of-the-art FET devices with dielectric resonators to yield excellent phase noise and stability. These oscillators are free running with extremely high frequency and power stability. The oscillators are generally designed and manufactured for fixed frequency applications. However, fine frequency adjustments can be achieved by mechanically tuning the provided self-locking screw. While the below standard models are offered for immediate production release, custom models are also available.
-
product
Solid State FET Transfer Switch, 300 KHz To 18 GHz
U9400C
Offers outstanding performance in isolation, switching speed, and video leakage over a broad operating frequency range
